User's Manual
Table Of Contents
- Scope of This Manual
- Conventions Used in This Manual
- Intended Audience for this Manual
- General Cautions and Warnings
- What is new?
- Overview Of Base Station
- 1.1 Conceptual Overview of the PacketMax System
- 1.1.1 Cell Size, Capacity, and Scalability
- 1.1.2 Frequency Bands
- 1.1.3 PacketMax Network Connectivity
- 1.2 Bridge Mode and VLAN Mode of Base Station
- 1.2.1 Bridge Mode
- 1.2.2 VLAN Mode
- 1.2.3 Point-to-Point Mode
- 1.3 Features of PacketMax System
- 1.3.1 The PacketMax System’s IP Network
- 1.3.2 Services
- 1.3.3 MIBs
- 1.3.4 Service Offerings and QoS
- 1.3.5 ARQ Feature
- 1.3.6 3 DES Encryption
- 1.3.7 Certificates and Management
- 1.3.8 Upgrades
- Base Station Components
- 2.1 PacketMAX Base Station
- 2.2 5-Slot ATCA Chassis
- 2.3 Wireless System Controllers
- 2.3.1 Major Differences Between WSC-S-24 and WSC-48
- 2.3.2 One Port WSC-S-24
- 2.3.3 QUAD Wireless Controller (QWC) Card - WSC-48
- 2.3.4 Compatibility matrix with radio
- 2.4 Main System Controller Card
- 2.5 MSC Redundancy
- 2.5.1 Redundancy support
- 2.6 AC Supply
- 2.7 Power LEDs and ESD connector
- 2.8 Hot Swap
- 2.8.1 WSC-48 Hot Swap
- 2.8.2 WSC-S-24 Hot Swap
- 2.8.3 MSC Hot Swap
- 2.9 Maintaining Proper Chassis Air FLow
- 2.10 Fan Unit
- 2.11 Serial Cable Pinout
- 2.11.1 Serial Connection Instructions
- 2.12 PacketMax 5000 Rear Panel
- 2.12.1 Grounding
- 2.12.2 DC Power Connection
- 2.13 AC Power Connection
- 2.13.1 Fuse
- 2.14 Base Station Radio
- Installing the Base Station IDU
- Installing the Base Station ODU Radio and Antenna
- 4.1 Radio Compatibility
- 4.2 Installing the Antenna
- 4.3 Installing the Base Station Radio ODU
- 4.3.1 3.3 and 3.5 GHz BSR Package Contents
- 4.3.2 5.8 GHz BSR Package Contents
- 4.3.3 Preparing and Mounting the 3.3 and 3.5 GHz BSR
- 4.3.4 Preparing and Mounting the 5.8 GHz BSR
- 4.3.5 Using the BSR with the Antenna and IDU
- Commissioning the Base Station
- 5.1 Summary of Configuration of Base Station
- 5.2 Establishing an Ethernet Connection with Cat-5 Cable
- 5.3 Establishing a Serial Connection to the Base Station
- 5.4 Configuring DHCP
- 5.5 Obtaining the MAC Address of the Base Station
- 5.6 Selecting Management or Data Traffic
- 5.7 Provisioning the Base Station with WaveCenter EMS
- 5.8 Rebooting the Base Station
- 5.9 Verifying Operations
- 5.10 Ensuring Encryption
- 5.11 Upgrading Base Station Manually
- 5.11.1 WSC upgrade
- 5.11.2 MSC Upgrade
- Event Reporting
- Command Line Interface (CLI)
- Cables, Spares and Accessories
- System Specifications
- D.1 Physical interfaces of PM 5000 - 12 sector
- D.2 Physical interfaces of PM 5000 - 4 sector
- D.3 QoS and Networking Parameters
- D.4 Dimensions and Weight
- D.5 Environmental
- D.6 Radio Specifications
- 4.6.1 PM-BSR-33 and PM-BSR-35 Radio Specifications
- 4.6.2 PM-BSR-58 Radio Specifications
- 4.6.3 Antenna Specifications
- D.7 Antenna Types, Maximum Gains and Maximum Output Power Point to Multipoint Operation
- D.8 Transmit Output Power Regulations
- Certifications
- Troubleshooting
1–10
PacketMax 5000 Installation and Operation Manual, 10007678 Rev J
Chapter 1. Overview Of Base Station
backhaul, it will not work. Ping will work if it is tagged with appropriate management
VLAN ID and it is sent through management port.
NOTE: Base Station Unit and Subscriber Stations need to be configured in the
VLAN Mode to avoid any configuration issues. It is not recommended to run the
base station in the Bridge Mode and Subscriber station in the VLAN Mode. However,
this combination might work but we do not guarantee and Aperto does not support
in this mode.
1.2.3 Point-to-Point Mode
The PacketMAX 5000/3000 Base Stations in combination with PacketMAX 100/300
Subscriber Stations provide high-speed, cost-effective links for point-to-point applica
-
tions. With unprecedented interference resilience and minimal spectrum usage, they
are ideal for such applications as high-speed backhaul of Wi-Fi hotspot networks,
higher-capacity alternatives to T1/E1 connections, and building-to-building connec
-
tions in the enterprise environments.
Features that support Point-to-Point applications include:
Support for 3.3, 3.5, and 5.8 GHz frequency bands
High interference immunity
Exceptional wireless range (up to approximately 35 to 50 miles/ 55 to 80 km,
depending on the frequency band)
Outdoor radio units with connectorized output for high-gain antennas to extend
the range of the wireless link.
Synchronization between units
Management via SNMP-based Element Management System.
Figure 1-6 PacketMAX 5000 in Point-to-Point Mode
Pont-to-Point Mode allows you to increase the number of supported hosts up to 7500.
You can enable or disable the Point-to-Point Mode from the SS Configuration screen
in the WaveCenter EMS Pro.
The following table lists the number of hosts supported in Point-to-Point mode, based
on the product and the frequency band: