User's Manual
Table Of Contents
- Scope of This Manual
- Conventions Used in This Manual
- Intended Audience for this Manual
- General Cautions and Warnings
- What is new?
- Overview Of Base Station
- 1.1 Conceptual Overview of the PacketMax System
- 1.1.1 Cell Size, Capacity, and Scalability
- 1.1.2 Frequency Bands
- 1.1.3 PacketMax Network Connectivity
- 1.2 Bridge Mode and VLAN Mode of Base Station
- 1.2.1 Bridge Mode
- 1.2.2 VLAN Mode
- 1.2.3 Point-to-Point Mode
- 1.3 Features of PacketMax System
- 1.3.1 The PacketMax System’s IP Network
- 1.3.2 Services
- 1.3.3 MIBs
- 1.3.4 Service Offerings and QoS
- 1.3.5 ARQ Feature
- 1.3.6 3 DES Encryption
- 1.3.7 Certificates and Management
- 1.3.8 Upgrades
- Base Station Components
- 2.1 PacketMAX Base Station
- 2.2 5-Slot ATCA Chassis
- 2.3 Wireless System Controllers
- 2.3.1 Major Differences Between WSC-S-24 and WSC-48
- 2.3.2 One Port WSC-S-24
- 2.3.3 QUAD Wireless Controller (QWC) Card - WSC-48
- 2.3.4 Compatibility matrix with radio
- 2.4 Main System Controller Card
- 2.5 MSC Redundancy
- 2.5.1 Redundancy support
- 2.6 AC Supply
- 2.7 Power LEDs and ESD connector
- 2.8 Hot Swap
- 2.8.1 WSC-48 Hot Swap
- 2.8.2 WSC-S-24 Hot Swap
- 2.8.3 MSC Hot Swap
- 2.9 Maintaining Proper Chassis Air FLow
- 2.10 Fan Unit
- 2.11 Serial Cable Pinout
- 2.11.1 Serial Connection Instructions
- 2.12 PacketMax 5000 Rear Panel
- 2.12.1 Grounding
- 2.12.2 DC Power Connection
- 2.13 AC Power Connection
- 2.13.1 Fuse
- 2.14 Base Station Radio
- Installing the Base Station IDU
- Installing the Base Station ODU Radio and Antenna
- 4.1 Radio Compatibility
- 4.2 Installing the Antenna
- 4.3 Installing the Base Station Radio ODU
- 4.3.1 3.3 and 3.5 GHz BSR Package Contents
- 4.3.2 5.8 GHz BSR Package Contents
- 4.3.3 Preparing and Mounting the 3.3 and 3.5 GHz BSR
- 4.3.4 Preparing and Mounting the 5.8 GHz BSR
- 4.3.5 Using the BSR with the Antenna and IDU
- Commissioning the Base Station
- 5.1 Summary of Configuration of Base Station
- 5.2 Establishing an Ethernet Connection with Cat-5 Cable
- 5.3 Establishing a Serial Connection to the Base Station
- 5.4 Configuring DHCP
- 5.5 Obtaining the MAC Address of the Base Station
- 5.6 Selecting Management or Data Traffic
- 5.7 Provisioning the Base Station with WaveCenter EMS
- 5.8 Rebooting the Base Station
- 5.9 Verifying Operations
- 5.10 Ensuring Encryption
- 5.11 Upgrading Base Station Manually
- 5.11.1 WSC upgrade
- 5.11.2 MSC Upgrade
- Event Reporting
- Command Line Interface (CLI)
- Cables, Spares and Accessories
- System Specifications
- D.1 Physical interfaces of PM 5000 - 12 sector
- D.2 Physical interfaces of PM 5000 - 4 sector
- D.3 QoS and Networking Parameters
- D.4 Dimensions and Weight
- D.5 Environmental
- D.6 Radio Specifications
- 4.6.1 PM-BSR-33 and PM-BSR-35 Radio Specifications
- 4.6.2 PM-BSR-58 Radio Specifications
- 4.6.3 Antenna Specifications
- D.7 Antenna Types, Maximum Gains and Maximum Output Power Point to Multipoint Operation
- D.8 Transmit Output Power Regulations
- Certifications
- Troubleshooting
A–5
PacketMax 5000 Installation and Operation Manual, 10007678 Rev J
Chapter A. Event Reporting
Table A-3 WSC related Alarms/Events in PM5000
Alarm Type Alarm Message in EMS Cause Resolution
WSC Card Status WSC Port No <Port No> has
NOT become operational
WSC <Port No> Down
WSC %d Connected [Event]
This alarm indicates that
WSC Card is operational
or Down.
When the WSC becomes
operational, an event will
indicate this in the future
release.
WSC Power Change WSC <Port No> : Info WSC Card Power Change
Cookie Mismatch Config Frame Params
COOKIE MISMATCH
<Cookie Id> from WSC <Port
No>
This happens when there
is an image mismatch
between components.
Image mismatch
between the compo-
nents. Reinstall
Image
WSC Cfg File Down-
load Error
WSC Cfg File Download Fail-
ure
WSC Cfg File Download
Success
Not able to download WSC
configuration file from the
TFTP server.
Check Network topol-
ogy. Make sure that
TFTP server is acces-
sible from Base Sta-
tion
WSC Cfg File Parse
Status
WSC Cfg File Parse Failure
WSC Cfg File Successfully
Parsed
Config file is not generated
correctly.
Re-check your config-
uration.
WSC Configured Card
not Present
WSC Port No <Port No> is
Configured but NOT Present
WSC card is not available
in the chassis even though
it has been configured from
EMS.
Insert a WSC card.
Unconfigured WSC
Card Present
Unconfigured WSC Port No
<PortNo> is Powered Up
This shows that an uncon-
figured WSC Card is
inserted
Configure WSC from
EMS.
WSC Card Not Pow-
ered
Configured WSC Port No
<Port No> is NOT Powered
Up
WSC Card is not working
properly
Hot Swap the WSC
card by removing and
re-inserting it back.
WSC Radio Link Status Radio Link State is ON
[Event]
Radio Link State is OFF
This indicates the status of
the Base Station Radio.
If Radio Link State is
OFF, check the RF
cable connection.