Datasheet

ManualsBrandsAPEM ManualsSwitches & ButtonsJoystick 4.5 V Screws IP68, IP69K 1 pc(s)

TS series

Proportional Hall effect thumbsticks

Distinctive features and specifications

APEM www.apem.com

Note: The company reserves the right to change specifications without notice.

 1 or 2 axis

 Pushbutton handle option

 Non-contact Hall effect technology

 Submersible to 1m (3.28ft) per IP68

 Threaded metal housing option

 Redundant outputs available

 USB outputs available

PUSHBUTTON SWITCH (Option 6 Handle)

• Electrical life: 100,000 cycles

• Rating: 50mA,12VDC.

• Terminal: Brass with silver plating

• Contact resistance: 100mΩ max

• Insulation resistance: 100MΩ min. 500VDC

• Dielectric strength: 250VAC /1 minute

• Contact arrangement : 1 pole 1 throw

• Operation force: 1.5lbf

• Stop strength: Max 3kgf vertical static load for 15 seconds

• Operating temperature: -25°C to +70°C (-13°F to +158°F)

• Storage temperature: -30°C to +85°C (-22°F to +185°F)

• Vibration resistance: MIL-STD-202F METHOD 201A

• Shock resistance: MIL-STD-202F METHOD 213B

MATERIALS

• Body: Glass filled nylon

• Threaded Body: Black oxide plated brass

• Boot: Silicone

• Handles: 1, 2, 3 - Glass filled nylon

4, 5, 6, 7, 8 - Silicone

MECHANICAL (FOR X, Y AXIS)

• Operating Force: 3.1N±0.5N (0.70lbf±0.11lbf)

• Maximum Vertical Load: 200N (45lbf)

• Maximum Horizontal Load: 150N (33.7lbf)

• Mechanical Angle of Movement: 50°

• Expected Life: 1 million cycles

• Mass/weight: 18.25g ± 5.0g (0.64oz±0.18oz)

• Lever Action (Centering): Spring centering

ENVIRONMENTAL

• Operating Temperature: -40°C to +85°C (-40°F to +185°F)

• Storage Temperature: -40°C to +85°C (-40°F to +185°F)

• Sealing: IP68, IP69K

• EMC Immunity Level: EN61000-4-3

• EMC Emissions Level: EN61000-6-3:2001

• ESD: EN61000-4-2

ELECTRICAL SENSOR

• Resolution: 1.22mV

• Supply Voltage Range: 5.00V±0.01V

• Reverse Polarity Max: -10V

• Overvoltage Max: 20V

• Output Impedance: 2Ω

• Return to Center Voltage Tolerance: ±200mV initial

NOTES:

Mounting accessories.

Standard hardware includes:

• For the Drop-in option – 4 push in connectors, drop-in bezel and an O-ring.

• For the Rear mount option: 4x1/2 FH SS Phil Screws and a rear mount bezel.

1 Force applied to the top of the castle cap.

2 All options are IP68 and IP69K rated, however Drop-in mounting does not

prevent panel ingress.

– All values are nominal.

Summary of content (6 pages)

PAGE 1
TS series Proportional Hall effect thumbsticks Distinctive features and specifications MECHANICAL (FOR X, Y AXIS) • • • • • • • Operating Force: 3.1N±0.5N (0.70lbf±0.11lbf)1 Maximum Vertical Load: 200N (45lbf)1 Maximum Horizontal Load: 150N (33.7lbf)1 Mechanical Angle of Movement: 50° Expected Life: 1 million cycles Mass/weight: 18.25g ± 5.0g (0.64oz±0.
PAGE 2
TS series Proportional Hall effect thumbsticks Overview TS Handle SERIES 0 1 2 3 4 5 6 7 8 A None Castle Winged Hat Conical Finger Tip Round Jog Pushbutton Mushroom* Low Profile* Handles 1, 2, 3 Termination¹ 1 2 3 4 5 Output Options 00 01 02 03 04 22AWG 25cm PTFE 28AWG 25cm PTFE 72” Overmold Cable with USB Male Type Connector 2.54mm (0.100”) Pitch TE Connector 2.54mm (0.
PAGE 3
TS series Proportional Hall effect thumbsticks Models and dimensions HANDLE OPTIONS 1. CASTLE 2. WINGED HAT Ø17.17 .676 (0.676) 3. CONICAL Ø17.30 .681 (0.681) Ø18.36 .723 (0.723) 19.84 .781 (0.781) 18.67 .735 (0.735) 4. FINGER TIP 20.35 .801 (0.801) 5. ROUND JOG Ø17.42 .686 (0.686) 6. PUSHBUTTON Ø17.22 .678 (0.678) Ø17.65 Ø.695 (0.695) 29.69 1.169 (1.169) 24.08 .948 (0.948) 7. MUSHROOM 19.99 .787 (0.787) 8. LOW PROFILE Ø20.32 .800 (0.800) Ø15.24 .600 (0.600) 20.27 .798 (0.798) 14.
PAGE 4
TS series Proportional Hall effect thumbsticks Models and dimensions – continued PLASTIC HOUSING - DROP-IN OPTION CUTOUT DIMENSIONS Ø25.65 (1.01) Ø2.87 (0.113) 4 x PUSH IN CONNECTORS 24.64 (0.97) DROP-IN BEZEL O-RING 24.64 (0.97) PLASTIC HOUSING - REAR MOUNT OPTION CUTOUT DIMENSIONS 4 x 1/2 FH SS PHIL SCREW Ø25.65 (1.01) Ø2.87 (0.113) CHAMFERED FOR #4 FLAT HEAD SCREW (4 PLACES) 24.64 (0.97) 1.00 (0.04) x 45º CHAMFER REAR MOUNT BEZEL 24.64 (0.
PAGE 5
TS series Proportional Hall effect thumbsticks Models and dimensions – continued VOLTAGE OUTPUT OPTIONS OPTION 0 4.5 4.0 4.0 3.0 2.5 2.0 1.5 1.0 3.5 3.0 2.5 2.0 1.5 1.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.5 0.5 0 0 0 MIN TRAVEL (º) MAX OPTION 4 MIN TRAVEL (º) MAX OPTION 5 5.0 OUTPUT VOLTAGE (V) 4.5 4.0 OUTPUT VOLTAGE (V) 4.5 3.5 3.0 2.5 2.0 1.5 1.0 0.5 MIN TRAVEL (º) 0 MAX OPTION 6 5.0 4.0 4.0 4.0 4.0 3.0 2.5 2.0 1.5 1.0 3.0 2.5 2.0 1.5 1.0 3.5 3.0 2.5 2.0 1.5 1.0 0.
PAGE 6
TS series Proportional Hall effect thumbsticks Overview CONNECTOR TERMINATION OPTION Single output configurations feature a five position TE 3-647166-5 connector. Dual output configurations feature a seven position TE 3-647166-7 connector. A mating harness is not included, but may be specified for single output configurations at the time of order for an additional charge. The five function harness is part number 505-499. The seven function harness is part number 505-500.