Datasheet

ManualsBrandsApem ManualsNon-Illuminated Pushbutton SwitchesPushbutton Switch, 200 mA, 12 VDC

APEM www.apem.com B2-145

FP series

Fully illuminated pushbutton switches - bushing Ø 24 mm - momentary or latching

Distinctive features and specifications

❑

Threaded bushing

❑

Full actuator or symbol illumination

❑

Large but lightweight

❑

Sealed to IP69K

❑

Pad printed or laser etched symbols

Pad printing

Non-illuminated

Laser

Illuminated

ELECTRICAL SPECIFICATIONS

• Max. current/voltage rating with resistive load :

- silver contacts (code 2) : 4A 12VDC

- gold plated contacts (code 4) : 200mA 12VDC

• Initial contact resistance : 50 mΩ max.

• Insulation resistance : 1 GΩ min. at 500VDC

• Dielectric strength : 1.000 Vrms 50 Hz min.

• Electrical life at full load :

- Momentary models : 1 million cycles (gold plated contacts)

400.000 cycles (silver contacts)

- Latching models : 200.000 cycles

MATERIALS

• Case : PA46

• Actuator : PA12

• Bushing/ bezel : PA66

• Contacts : silver (code 2)

or silver, gold plated (code 4)

• Cable : length 300 mm, section

depending on switch model

• Terminal seal : epoxy or

overmolding

GENERAL SPECIFICATIONS

• Front panel sealing : IP69K according to DIN 40050-9

• Panel thickness : 1(.039) to 18 mm (.708) max.

• Total travel : 2,5 mm ± 0,5 mm

• Typical operating force : 8N ± 2N

• Low level or mechanical life :

- Momentary models : 1 million cycles

- Latching models : 200.000 cycles

• Torque : 3 Nm max. applied to nut

• Operating temperature : -40°C to +75°C

WIRING DIAGRAM

CFP24W-A

POLE 2

LED

POLE 1

LED

FICHIER: CFP24W

le 25/09/14

ECHELLE: 0.625

indice A

➞

Flat

The company reserves the right to change specifications without notice.

UG1410-A-R2

Summary of content (8 pages)

PAGE 1
FP series Fully illuminated pushbutton switches - bushing Ø 24 mm - momentary or latching Distinctive features and specifications UG1410-A-R2 ❑ Threaded bushing ❑ Full actuator or symbol illumination ❑ Large but lightweight ❑ Sealed to IP69K ❑ Pad printed or laser etched symbols Pad printing Laser B2 Non-illuminated Illuminated ELECTRICAL SPECIFICATIONS MATERIALS • Max.
PAGE 2
FP series Fully illuminated pushbutton switches - bushing Ø 24 mm - momentary or latching Overview FP Actuator SERIES Model A Threaded bushing, dia. 24 mm P R F Terminals Electrical function Round, flat Round, curved Round, curved, flush New! 1 3 OFF - ON Normally open (NO) 1 2 3 LED control and No of poles A B C D E B2 Contact mat.
PAGE 3
FP series Fully illuminated pushbutton switches - bushing Ø 24 mm - momentary or latching • Three terminal types • Curved or flat actuator 11.30 (.445) 4.80 (.189) 6.60 (.260) Ø (.9 24 53 .20 DI A) Ø18.50 (.728DIA) (1 Ø27 .08 .5 3D 0 IA ) 2.80 (.110) Ø18.50 (.728DIA) (1 Ø27 Ø24.00x1.00 .08 .5 SI 3D 0 IS) (.944DIAx1.00 IA ) B2 6.60 (.260) 4.80 (.189) 22.50 (.886) ➞ Flat LATCHING OFF - OFF ON ON 0.50 (.020) 0.50 (.020) Ø18.50 (.728DIA) CFPDT1-A (1 Ø27 .08 .5 3D 0 IA ) Ø24.00x1.00 SI (.
PAGE 4
FP series Fully illuminated pushbutton switches - bushing Ø 24 mm - momentary or latching Options LED CONTROL AND NUMBER OF POLES Complete the model numbers on previous pages with one of the following codes.
PAGE 5
FP series Fully illuminated pushbutton switches - bushing Ø 24 mm - momentary or latching Options LED RESISTOR 0 1 2 5 6 No resistor supplied 12VDC resistor 24VDC resistor 15VDC resistor 30VDC resistor B2 MARKING X 1 2 No marking Pad printing Laser SYMBOLS Blank ➞ Flat No symbol Available symbols See end of K-range, section D. Ø (.6 16 30 .00 DI A) ➞ Marking colour White marking for illuminated actuators (laser etching) and non-illuminated black actuators (pad printing).
PAGE 6
FP series Fully illuminated pushbutton switches - bushing Ø 24 mm - momentary or latching Symbols Most symbols meet the ISO 7000 standard “graphical symbols for use on equipments” (code given in bracket in the description). Contact us for symbols not featured in the following tables. Legend scale : Depending on space available on the product (see “Symbols” section).
PAGE 7
FP series Fully illuminated pushbutton switches - bushing Ø 24 mm - momentary or latching Symbols Most symbols meet the ISO 7000 standard “graphical symbols for use on equipments” (code given in bracket in the description). Contact us for symbols not featured in the following tables. Legend scale : Depending on space available on the product (see “Symbols” section).
PAGE 8
FP series Fully illuminated pushbutton switches - bushing Ø 24 mm - momentary or latching Symbols Most symbols meet the ISO 7000 standard “graphical symbols for use on equipments” (code given in bracket in the description). Contact us for symbols not featured in the following tables. Legend scale : Depending on space available on the product (see “Symbols” section).