Datasheet

ManualsBrandsApem ManualsIlluminated Pushbutton SwitchesIlluminated Pushbutton Switch 1NO 200 mA 12 VDC IP69K

APEM www.apem.com 1

FD series

Double icon illuminated pushbuttons - bushing Ø 24 or 26 mm - momentary or latching

Distinctive features and specifications

❑

Double icon actuator

❑

Snap-in and threaded bushing models

❑

Suited for integrated designs

❑

Large but lightweight

❑

Sealed to IP69K (threaded bushing version)

ELECTRICAL SPECIFICATIONS

• Max. current/voltage rating with resistive load :

- silver contacts (code 2) : 4A 12VDC

- gold plated contacts (code 4) : 200mA 12VDC

• Initial contact resistance : 50 mΩ max.

• Insulation resistance : 1 GΩ min. at 500VDC

• Dielectric strength : 1.000 Vrms 50 Hz min.

• Electrical life at full load :

- Momentary models : 1 million cycles (gold plated contacts)

400.000 cycles (silver contacts)

- Latching models : 200.000 cycles

MATERIALS

• Case : PA46

• Actuator : PA12

• Bushing/ bezel : PA66

• Contacts : silver (code 2)

or silver, gold plated (code 4)

GENERAL SPECIFICATIONS

• Front panel sealing :

- Threaded bushing version : IP69K according to DIN 40050-9

- Snap-in version : IP54 according to IEC 60529 with panel gasket and

2 mm panel thickness

• Panel thickness :

- Snap-in version : 1,5 (.059) to 2 mm (.078) with panel gasket

2 (.078) to 2,5 mm (.885) without panel gasket

- Threaded bushing version :1(.039) to 18 mm (.708) max.

• Total travel : 2,5 mm ± 0,5 mm

• Typical operating force : 8N ± 2N

• Low level or mechanical life :

- Momentary models : 1 million cycles

- Latching models : 200.000 cycles

• Torque : 3 Nm max. applied to nut

• Operating temperature : -40°C to +75°C

The company reserves the right to change specifications without notice.

WIRING DIAGRAM

CFP24W-A

POLE 2

LED

OLE 1

LED

FICHIER: CFP24W

le 25/09/14

ECHELLE: 0.625

indice A

➞

Flat

FD1506-A

Summary of content (4 pages)

PAGE 1
FD series Double icon illuminated pushbuttons - bushing Ø 24 or 26 mm - momentary or latching Distinctive features and specifications FD1506-A ❑ Double icon actuator ❑ Snap-in and threaded bushing models ❑ Suited for integrated designs ❑ Large but lightweight ❑ Sealed to IP69K (threaded bushing version) ELECTRICAL SPECIFICATIONS MATERIALS • Max.
PAGE 2
FD series Double icon illuminated pushbuttons - bushing Ø 24 or 26 mm - momentary or latching Overview FD Actuator SERIES Models A B P Terminals Electrical function Round, flat 1 3 1 Solder lugs OFF - ON Normally open (NO) Threaded bushing, dia. 24 mm Snap-in, dia.
PAGE 3
FD series Double icon illuminated pushbuttons - bushing Ø 24 or 26 mm - momentary or latching • Solder lugs • Flat actuator To order a product, replace • with one of the codes selected under “LED control and number of poles” below, then add the desired options.
PAGE 4
FD series Double icon illuminated pushbuttons - bushing Ø 24 or 26 mm - momentary or latching Options CONTACT MATERIALS 2 4 Silver Silver, gold plated ACTUATOR COLOR 8 Smoke black BEZEL COLOR 2 Black LED COLOR F Red/green LED RESISTOR 0 1 2 No resistor supplied 12V resistor 24V resistor SYMBOLS 3 5 4 ➞ Flat ON (green) / OFF ( red) with ring ➞ I (green) / O ( red) with ring www.apem.