Installation Guide

ManualsBrandsAPC ManualsElectronicsSmart-UPS SRT 1500VA RM 120V

Table Of Contents

Installation Guide Smart-UPS

™

On-Line

SRT1000/SRT1500 XLA Tower/Rack-Mount

Important Safety Messages

Read the instructions carefully to become familiar with the equipment before attempting to install, operate, service or

maintain the UPS. The following special messages may appear throughout this manual or on the equipment to warn of

potential hazards or to call attention to information that clarifies or simplifies a procedure.

The addition of this symbol to a Danger or Warning product safety label indicates that an electrical hazard

exists which will result in personal injury if the instructions are not followed.

The addition of this symbol to a Warning or Caution product safety label indicates that a hazard exists that

can result in injury and product damage if the instructions are not followed.

Information

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious

injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious

injury.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate

injury.

NOTIC E

NOTICE is used to address practices not related to physical injury.

Summary of content (16 pages)

PAGE 1
Installation Guide Smart-UPS™On-Line SRT1000/SRT1500 XLA Tower/Rack-Mount Important Safety Messages Read the instructions carefully to become familiar with the equipment before attempting to install, operate, service or maintain the UPS. The following special messages may appear throughout this manual or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure.
PAGE 2
Safety and General Information • Adhere to all national and local electrical codes. • All wiring must be performed by a qualified electrician. • Changes and modifications to this unit not expressly approved by APC could void the warranty. • This UPS is intended for indoor use only. • Do not operate this UPS in direct sunlight, in contact with fluids, or where there is excessive dust or humidity. • Be sure the air vents on the UPS are not blocked. Allow adequate space for proper ventilation.
PAGE 3
Battery safety • When replacing batteries, replace with the same number and type of batteries as originally installed in the equipment. • Batteries typically last for two to five years. Environmental factors impact battery life. Elevated ambient temperatures, poor quality utility power, and frequent short duration discharges will shorten battery life. Batteries should be replaced before end of life. • Replace batteries immediately when the unit indicates battery replacement is necessary.
PAGE 4
Package Contents Inspect the contents upon receipt. Notify the carrier and dealer if the unit is damaged. Included with all models Front bezel NC models only RJ45 to DB9 cable User Documentation CD.
PAGE 5
Specifications For additional specifications refer to the APC by Schneider Electric web site, www.apc.com. Environmental Temperature Elevation Operating 0º to 40º C (32º to 104º F) Storage -15º to 45º C (5º to 113º F) Operating 0 - 3,000 m (0 - 10,000 ft) Storage 0 - 15,000 m (50,000 ft) Humidity 0% to 95% relative humidity, non-condensing Protection Class IP 20 rating Note: Charge the battery modules every six months during storage. Environmental factors impact battery life.
PAGE 6
Battery NOTICE RISK OF EQUIPMENT DAMAGE • Replace the battery at least every 5 years. • Replace the battery immediately when the UPS indicates battery replacement is necessary. Failure to follow these instructions can result in equipment damage SRT1000/SRT1500 models Battery type Sealed, maintenance-free, Valve Regulated Lead-Acid battery Replacement battery module APCRBC155 This UPS has swappable battery modules. Refer to the appropriate replacement battery user manual for installation instructions.
PAGE 7
Electrical CAUTION RISK OF FIRE, RISK OF ELECTRIC SHOCK Connect the UPS models only to a circuit provided with recommended maximum branch circuit overcurrent protection in accordance with the National Electrical Code, ANSI/NFPA 70 and the Canadian Electrical Code, Part I, C22.1. Failure to follow these instructions can result in fire, and minor or moderate injury.
PAGE 8
Remove Battery Module CAUTION RISK OF FALLING EQUIPMENT • • • • • The equipment is heavy. Each APCRBC155 battery module weighs 11 kg (24.25 lb). Always practice safe lifting techniques adequate for the weight of the equipment. Remove the battery modules before installing the UPS. Use the battery module handle to slide the battery modules in or out of the UPS. Do not use the battery module handle to lift or carry the battery module.
PAGE 9
Rack-Mount Installation Refer to the Rail Kit Installation Guide for instructions on rail installation. CAUTION RISK OF DAMAGE TO EQUIPMENT OR PERSONNEL • The equipment is heavy. Always practice safe lifting techniques adequate for the weight of the equipment. • Always use the recommended number of screws to secure brackets to the UPS. • Always use the recommended number of screws to secure the UPS to the rack. • Always install the UPS at the bottom of the rack.
PAGE 10
 suo1205a x3  x4 10 suo1207a  suo1206a  Smart-UPS On-Line SRT1000/SRT1500 Tower/Rack-Mount 2U 59a su08
PAGE 11
Tower Installation CAUTION RISK OF FALLING EQUIPMENT • The equipment is heavy. Each APCRBC155 battery module weighs 11 kg (24.25 lb). • Always practice safe lifting techniques adequate for the weight of the equipment. • Remove the battery modules before installing the UPS. • Use the battery module handle to slide the battery modules in or out of the UPS. • Do not use the battery module handle to lift or carry the battery module.
PAGE 12
suo0875c  Rear Panel Features Note: Refer to the table “Key to identify rear panel features” on page 13, that provides a key to the callout numbers for the rear panel graphics depicted in this manual.
PAGE 13
Key to identify rear panel features  SmartSlot The SmartSlot can be used to connect optional management accessories.  AC input power cable or hardwire input box All models have factory installed input power cables. Hardwired input box is an optional accessory.  External battery power and Use the external battery cable on the XLBP to connect the UPS and XLBP. communication connector XLBPs provide extended runtime during power outages.
PAGE 14
UPS Display Interface  POWER ON/OFF button Button illumination indications: -No illumination, the UPS and the output power are off -White illumination, the UPS and the output power are on -Red illumination, the UPS is on and the output power is off  Load icon Disable/mute audible alarm icon LOAD Output 120.
PAGE 15
Operation Mode Icons On-Line mode: The UPS is supplying conditioned mains power to connected equipment. Bypass mode: The UPS is in Bypass mode and the connected equipment will receive mains power as long as the input voltage and frequency are within the configured limits. Green mode: When in Green mode mains power is sent directly to the load. In the event of a mains power outage, there will be an interruption in power to the load of up to 10 ms while the UPS switches to On-Line or Battery mode.
PAGE 16
Menu overview The display interface has Standard and Advanced menu screens. The preference for Standard or Advanced menu selections is made during initial installation and can be changed at any time through the Configuration menu. The Standard menus include the most commonly used options. The Advanced menus provide additional options. Note: Actual menu screens may differ by model and firmware version. Refer to the UPS Operation Manual for menu configuration details.