User Manual

ManualsBrandsAPC ManualsOtherAPC Power Saving Back-UPS Pro

Safety and General Information

Inspect the package contents upon receipt. Notify the carrier and

dealer if there is any damage.

SAVE THESE INSTRUCTIONS - This section contains important

instructions that should be followed during installation and maintenance

of the UPS and batteries.

Inventory

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• This UPS is intended for indoor use only.

• Do not operate this UPS in direct sunlight, in contact with fluids, or where there is excessive

dust or humidity.

• Connect the UPS power cable directly to a wall outlet.

• Be sure the air vents on the UPS are not blocked. Allow adequate space for proper ventilation.

• Servicing of batteries should be performed or supervised by personnel knowledgeable about

batteries and required precautions.

• A battery can present a risk of electric shock and burns by high short-circuit current.

• Failed batteries can reach temperatures that exceed the burn thresholds for touchable

surfaces.

Failure to follow these instructions will result in death or serious injury.

bu001b

User Manual Back-UPS

™

Pro

BR650/900/1300/1600MI

Summary of content (12 pages)

PAGE 1
User Manual Back-UPS™ Pro BR650/900/1300/1600MI Safety and General Information Inspect the package contents upon receipt. Notify the carrier and dealer if there is any damage. SAVE THESE INSTRUCTIONS - This section contains important instructions that should be followed during installation and maintenance of the UPS and batteries. DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH • • • • • • • This UPS is intended for indoor use only.
PAGE 2
Connect the Battery The UPS is shipped with the battery disconnected. bu024c bu025c BR650MI /BR900MI  Remove the battery. Connect the wire.  Push the battery into the unit.  Replace the battery door. bu026c  Remove the battery door. BR1300MI / BR1600MI bu055b bu057b RED LABEL ON TOP  Remove the battery door.  Remove the battery.  Push the battery into the unit. bu060b  Flip or turn the battery 180 degrees upward/downward to let green side of the label face up.
PAGE 3
Install PowerChute™ Personal Edition Software Use PowerChute Personal Edition software to configure the UPS settings. During a power outage, PowerChute will save any open files on your computer and shut it down. When power is restored, it will restart the computer. Note: PowerChute is only compatible with a Windows operating system. If you are using Mac OSX, use the native shutdown feature to protect your system. See the documentation provided with your computer.
PAGE 4
 USB and Serial Data port To use PowerChute Personal Edition, connect the supplied USB cable or an optional serial cable (not supplied).  Telephone Cable Connect a telephone cable to the IN port, and connect a modem to the Surge Protected ports OUT port.  AC Power Input Use a power cable to connect the unit to AC power.  Battery Backup During a power outage or other AC problems, the Battery Backup outlets outlets with Surge receive power for a limited time from the Back-UPS.
PAGE 5
Front panel buttons and display interface Use the three buttons on the front panel of the Back-UPS and the display interface to configure the Back-UPS. Front panel bu109g  Mute button  Power On/Off button  Display button  Display interface On Line: The Back-UPS is supplying conditioned AC power to connected equipment Load Capacity: The load is indicated by the number of sections illuminated, one to five. Each bar represents 20% of the load.
PAGE 6
Mute: If the line through the speaker icon is illuminated, the audible alarm has been turned off. Replace Battery: The battery is nearing the end of its useful life. Replace the battery as early as possible. On Battery: The Back-UPS is supplying battery backup power to the connected equipment, it will beep four times every 30 seconds. Alarms and System Errors Audible indicators Back-UPS is running on battery. You should consider saving any work in progress.
PAGE 7
System errors The Back-UPS will display these error messages. Except for errors F01 and F02, contact SEIT Technical Support. F01 F02 bu088a F03 F04 F05 F06 F07 F08 F09 Turn the Back-UPS off. Disconnect non-essential On-Battery Overload equipment from the Battery Backup outlets and the turn Back-UPS on. Turn the Back-UPS off. Disconnect all equipment from the Battery Backup outlets and On-Battery Output the turn Back-UPS on. Re-connect equipment one item Short at a time.
PAGE 8
Function Button Quick Reference Timing (seconds) UPS Status Power On 0.2 Off Power Off 2 On 0.2 On Verify the status or condition of the Back-UPS. The LCD will illuminate for 60 seconds. Press the button the toggle into various information. 2 On The LCD will illuminate and the Back-UPS will beep to confirm the Full-Time mode. The LCD will darken and the Back-UPS will beep to confirm the PowerSaving mode.
PAGE 9
Troubleshooting Problem Possible Cause Corrective Action The Back-UPS is not connected to AC power. The circuit breaker has been tripped. Ensure that the Back-UPS is securely connected to an AC outlet. Disconnect non-essential equipment from the Back-UPS. Reset the circuit breaker. Re-connect equipment one item at a time. If the circuit breaker is tripped again, disconnect the device that caused the trip. Connect the battery. Back-UPS will not switch on. The internal battery is not connected.
PAGE 10
Specifications Model BR650MI BR900MI BR1300MI BR1600MI VA 650 VA 900 VA 1300 VA 1600 VA Maximum Load 390 W 540 W 780 W 960 W Nominal Input Voltage 220 - 240 Vac Online Input Voltage Range 176 - 294 Vac Automatic Voltage Regulation Boost by +11.5% when input voltage drops below limit Frequency Range 50/60 Hz ± 3 Hz Battery Type Trim by -11.
PAGE 11
Battery Replacement CAUTION RISK OF HYDROGEN SULPHIDE GAS AND EXCESSIVE SMOKE • • • • • Replace the battery at least every 5 years. Replace the battery immediately when the UPS indicates battery replacement is necessary. Replace battery at the end of its service life. Replace batteries with the same number and type of batteries as originally installed in the equipment.
PAGE 12
APC by Schneider Electric IT Customer Support Worldwide For country specific customer support, go to the APC by Schneider Electric Web site, www.apc.com. © 2019 APC by Schneider Electric. APC, the APC logo, Back-UPS, and PowerChute are owned by Schneider Electric Industries S.A.S. or their affiliated companies. All other trademarks are property of their respective owners.