BroadBand CTFRP Ferroresonant Power Supply User Manual 990-5516A 10/2004
Chapter 1 General Information The CTFRP Series Power Supply provides a power source for broadband cable operations. Important Safety Instructions – Save These Instructions This Safety Guide contains important instructions that should be followed during installation and maintenance of the APC equipment and batteries. It is intended for APC customers who setup, install, relocate, or maintain APC equipment. Changes and modifications to this unit not expressly approved by APC could void the warranty.
Specifications Environmental Specifications Operating Temperature -40º F to +140º F (-40º C to +60º C) Humidity 5% to 95% noncondensing within enclosure Physical Specifications Characteristic Specification Height CTFRP6XXX CTFRP9015 11.5″ (29 cm) 13” (33 cm) Width CTFRP6XXX CTFRP9015 6″ (15 cm) 7” (18 cm) Depth CTFRP6XXX CTFRP9015 6″ (15 cm) 9.
Chapter 2 Installation and Maintenance Only trained service personnel should install and maintain the Power Supply. Prior to installing the Power Supply, an APC approved enclosure must be installed and AC line voltage must be routed to the enclosure. Local, state, federal and/or National Electric Code (NEC) regulations regarding location, permits and electrical wiring must be adhered to. Do not operate the Power Supply where the temperature and humidity are outside the specified limits.
. Locate the position on the pole where the Power Supply is to be located. 7. Drill two 3/4” holes vertically spaced 6” (15.2 cm) apart. 8. Attach the top of the mounting bracket to the pole using a 5/8” pole bolt and washer. Repeat this procedure for the bottom of the bracket. 9. Ensure that the power supply enclosure is closed and locked. 10. Holding the Power Supply above the bracket slide the unit down the bracket.
Chapter 3 Operation CTFRP-6XXX Series #370 T - 1 TWI 14 AWG 14 AWG BLK BLK #210 15A BREAKER/SW SW 1:2 WHT SW 1:1 TW2 MOV #260 C – 1 #380 C 1:1 TW3 15UF C 12 14 AWG RED TW5 VIL 12 AWG TW4 GRN/YEL 15 AWG RED 14 AWG TW6 16 AWG BRN GRN/YEL GRN W7 YEL GND - 1 OUTPUT OPTION CONNECTOR JUMPERED IF NOT USED 1 GN VIL W1 YEL 12 AWG W4 W3 18 AWG GRN BLK WHT 14 AWG 16 AWG W2 GRN/YEL 1 2 3 16 AWG GRN/YEL W6 GND - 2 2 IN 3 OT J2 WS 1B BLK/WHT #110 LT1 LT-1 P2 LT-1 J1 60 VAC RMS L N G LINE IN OUTP
CTFRP-90XXX Series Initial Start-up 1. Turn the utility breaker to the ON position. 2. Turn the power supply switch to the ON position. Note: The output indicator located at the bottom of the unit is illuminated. 3. Using a True RMS voltmeter check for voltage at the stinger lug. The unit is now operational. To shut down the Power Supply 1. Move the power supply switch to the OFF position. 2. Move the utility circuit breaker to the OFF position.
Chapter 4 Service, Contact and Warranty Information Service APC makes every effort to ensure parts and equipment arrive in working condition. Occasionally, it may be necessary to return parts or equipment that are not in working condition. If the unit requires service do not return it to the dealer. Follow these steps: 1. Contact APC Customer Support through the APC Web site, www.apc.com/support. Note the product model number, the serial number, and the date purchased.
Limited Warranty American Power Conversion (APC) warrants its products to be free from defects in materials and workmanship for a period of two years from the date of purchase. Its obligation under this warranty is limited to repairing or replacing, at its own sole option, any such defective products. To obtain service under warranty you must obtain a Returned Material Authorization (RMA) number from customer support.
