Datasheet

3 E NROLL F INGERPRINT
Once you have selected the APC Biometric Device icon, the
Choose Finger screen (Figure 15) will be displayed.
Figure 15. Choose Finger Screen
A. Click on the fingertip of the fingerprint you wish to
enroll; a red arrow will appear above the selected finger
(Figure 16). Click Next or Cancel.
Figure 16. Selected Finger Screen
B. The software will then display the Blank Capture
Fingerprint screen (Figure 16). Place the chosen
finger over the Sensor and Drive Ring (Figure 17).
Figure 17. Blank Capture Fingerprint Screen
Note: Place the finger on the BioCB40 sensor and drive
ring (Figure 18) for scanning. Use light, but firm and
steady pressure. Ensure the finger makes contact with
the BioCB40 sensor and the surrounding drive ring.
APC OmniPass works best when it has an image of the
center of a fingerprint (core image).
Capture the full area of the fingerprint by placing the
finger flat on the BioCB40 sensor. Do not place only the
fingertip on the sensor, as it contains insufficient image
data for a high-quality fingerprint
Figure 18. CB40 Sensor and Drive Ring
C. As you place your fingertip on the Sensor and Drive
Ring (Figure 19), the system will record your fingerprint
and display it in the gray box (Figure 20) and the box
numbered “1” will turn green. You must raise the finger
straight up and put it back on the sensor up to 3 times
before the fingerprint is successfully recorded. Each
time the fingerprint is recorded, another numbered box
will turn green.
Figure 19. Finger Placement
Figure 20. Capture Fingerprint Screen
D. Once the device has successfully recorded your
fingerprint, the system will display the Verify
Fingerprint screen (Figure 21). Place your finger on
the Sensor and Drive Ring.
Figure 21. Verify Fingerprint Screen
E. After the system has verified your fingerprint, it will then
ask if you would like to enroll additional fingerprints
(Figure 22). To enroll additional fingerprints, click Yes.
To stop, click No.
Figure 22. Additional Fingerprints Prompt
4 S ELECT A UDIBLE AND T ASKBAR
S ETTINGS
After enrolling and verifying your fingerprint, the system will
allow you to set certain audible prompts, as well as what is
displayed in the taskbar located at the bottom-right side of
your display (Figure 23).
Figure 23. Audio and Taskbar Settings Screen
A. Click on the circle next to the desired selection, then
click on Next, Cancel, or Start Over.
B. Once the settings have been chosen, select Next and
the Congratulations screen (Figure 24) will be
displayed. Click Done to complete the enrollment
process; the Logon New User screen (Figure 25) is
displayed. Click Yes to logon the new user, or click No
to stop the installation process.
M. The software will then display the Verify Username
and Password screen (Figure 12). Enter your
Windows Username, Domain, and Password.
Figure 12. Verify User Name and Password Screen
N. During enrollment, the Select Authentication Device
screen is displayed (Figure 13).
Figure 13. Select Authentication Device Screen
O. Click on the APC Biometric Device Icon (fingerprint
graphic, Figure 13 and 14), the fingerprint box will
change color (Figure 14).
Figure 14. Select Authentication Device Screen
I. Once setup is complete, the Installing/Updating
Driver for Devices... screen is displayed (Figure 8).
Figure 8. Installing/Updating Driver for Devices... Screen
J. After the software installation is complete, the
InstallShield Wizard Complete screen is displayed
(Figure 9). In order to the software installation to take
affect, you must restart your computer. Click the circle
next to “Yes. I want to restart my computer now”,
then click Finish to perform a restart. To restart your
computer at a later time, click the circle next to “No, I
will restart my computer later”.
Figure 9. InstallShield Wizard Complete Screen
K. After restarting your computer, the Windows log-in
screen will appear. The Omnipass software will also
display a Logon User Authentication screen (Figure
10). Enter your User Name and Password in the
Windows logon screen. You do not have to do anything
with the Logon User Authentication screen at this time.
Figure 10. Logon User Authentication Screen
L. After logging in, you will be brought to the Omnipass
Welcome screen (Figure 11). Please click Enroll.
Figure 11. OmniPass Welcome Screen