Owners manual

ManualsBrandsAPC ManualsEmergency Power SupplyRetail Battery Back UPS XS 1300VA Discontinued by Manufacturer

Installation and Operation Back-UPS

™

BX1300/1500 G/G-CA, BN1350G

Inventory

Safety and General Information

Inspect the package contents upon receipt. Notify the carrier and dealer if

there is any damage.

Read the Safety Guide supplied with this unit before installing the UPS.

• This UPS is intended for indoor use only.

• Do not operate this UPS in direct sunlight, in contact with fluids, or where there is excessive dust or humidity.

• Be sure the air vents on the UPS are not blocked. Allow adequate space for proper ventilation.

• The battery typically lasts for two to five years. Environmental factors impact battery life. Elevated ambient

temperatures, poor quality AC power, and frequent short duration discharges will shorten battery life.

• Connect the UPS power cable directly to a wall outlet. Do not use surge protectors or extension cords.

Connect the Battery

The battery charges fully during the first 16 hours while the Back-UPS is operating on AC power. Do not

expect full battery runtime capability during the initial charge period.

Battery wear is not covered by the Limited Warranty.

There are no serviceable parts in the Back-UPS. Do not attempt to open or repair the Back-UPS as this

will void the warranty.





bu001a

bu055a

bu057a

bu059a

bu058a

bu060a

Summary of content (10 pages)

PAGE 1
Installation and Operation Back-UPS™ BX1300/1500 G/G-CA, BN1350G bu001a Inventory Safety and General Information Inspect the package contents upon receipt. Notify the carrier and dealer if there is any damage. Read the Safety Guide supplied with this unit before installing the UPS. • • • • This UPS is intended for indoor use only. Do not operate this UPS in direct sunlight, in contact with fluids, or where there is excessive dust or humidity. Be sure the air vents on the UPS are not blocked.
PAGE 2
Replace Battery Deliver the used battery to a recycling facility. Replace the used battery with an APC by Schneider Electric approved battery. Replacement batteries can be ordered through the APC by Schneider Electric Web site, www.apc.com. Battery replacement parts are APCRBC123 for Back-UPS BX1300G BX1300G-CA and BN1350G, and APCRBC124 for BX1500G and BX1500G-CA.
PAGE 3
Connect the Equipment  Telephone/ Connect a telephone cable to the In port, and a modem to the Out Network port port.  Data port To use PowerChute Personal Edition, connect the supplied USB software cable or serial cable.  Ground Connect the ground lead from an additional surge suppression device such as a stand-alone data line surge protector. screw  Building  Controlled These outlets provide surge protection for connected devices.
PAGE 4
Operation Power-Saving feature This Back-UPS is equipped with power saving outlets that conserve electricity. Configure the Back-UPS to recognize a Master device, such as a computer or an A/V receiver, and controlled peripheral devices, such as a printer, speakers, or a scanner. When the Master device goes into Standby or Hibernation mode, or is turned off, the controlled device(s) will be turned off as well. The Back-UPS ships with this Power-Saving feature DISABLED.
PAGE 5
Front panel buttons and display Use the buttons on the front panel of the Back-UPS and the display interface to configure the Back-UPS. Front panel MUTE button POWER button DISPLAY button Display bu109g     On Line: The Back-UPS is supplying conditioned AC power to connected equipment. Power-Saving Function: The MASTER and CONTROLLED outlets are enabled. The power-saving feature is active when the master device goes into Standby or Hibernation mode.
PAGE 6
Replace Battery: The battery is nearing the end of its service life. Replace the battery. On Battery: The Back-UPS is supplying battery backup power to the connected equipment. Modes of operation Press DISPLAY to scroll through the display screens.
PAGE 7
Feature Quick Reference Function Button Timing UPS (seconds) Status Description Power POWER ON 0.2 Off Press the POWER ON/OFF button to turn on the Back-UPS and operate on AC power. If AC input power is not available the Back-UPS will operate on battery power. POWER OFF 2 On Press the POWER ON/OFF button to turn off the Back-UPS. The Back-UPS will continue to provide surge protection to the Surge Protection outlets. 0.2 On Verify the status or condition of the Back-UPS.
PAGE 8
Troubleshooting Problem Back-UPS will not turn on. The Back-UPS is operating on battery power, while connected to AC power. Possible Cause Corrective Action The Back-UPS is not connected to AC power. Be sure that the Back-UPS is securely connected to an AC outlet. The circuit breaker has been tripped. Disconnect non-essential equipment from the Back-UPS. Reset the circuit breaker. Reconnect equipment one item at a time.
PAGE 9
Specifications Model 1500 VA 1350 VA 1300 VA Maximum Load 865 W 810 W 780 W Nominal Input Voltage 120 Vac Online Input Voltage Range 88 Vac to139 Vac Automatic Voltage Regulation + 11.5% Boost Only Frequency Range 50/60 Hz ± 1 Hz On battery Waveshape Step approximated sinewave Typical Recharge Time 16 hours Transfer Time 8 ms, maximum Operating Temperature 0º to 40º C (32º to 104º F) Storage Temperature -5º to 45º C (23º to 113º F) Unit Dimensions 11.9 × 4.4 × 15.0 in (30.1 × 11.
PAGE 10
Warranty The standard warranty is three (3) years from the date of purchase. Schneider Electric IT (SEIT) standard procedure is to replace the original unit with a factory reconditioned unit. Customers who must have the original unit back due to the assignment of asset tags and set depreciation schedules must declare such a need at first contact with an SEIT Technical Support representative.