Installation manual

Battery Replacement
AIS® 3000 & XR Battery Enclosure 10-40kVA, 400V, Operation Manual – 990-2259 25
Battery Module removal
Follow the below procedures if you need to change or add a Battery Module, e.g. if you receive a
display message reporting a bad battery, or if you need to add batteries for increased runtime:

When removing Battery Modules, start from the highest level and work down.

Holding the battery handle, gently push the battery upwards and pull it halfway out of the
Enclosure. A lock mechanism prevents it from being pulled all the way out.

To release the battery from the lock mechanism, one person gently pushes the battery upwards
again and pulls it out, while the other person supports the battery.
How to install a Battery Module
If additional batteries are needed for extra run-time, or if you install battery replacement modules,
follow the below procedure:
10
/10
0B
as
e
-
T
Pro
be
A
P961
9
N
e
twork Manag
e
men
t Card
E
M
!
R
e
s
e
t
O
ut
p
ut
P
w
r
Z
on
e
10/10
0
Model:
Seria
l
:
BATTERY UNIT
Model:
Seria
l:
BATTERY UNIT
Model:
Serial:
BATTERY UNIT
M
o
d
e
l:
Serial:
BATTERY UNIT
M
o
d
el:
Ser
i
al:
BAT
TERY UNIT
Model:
S
eri
al:
BATTERY UNIT
Model:
S
er
ia
l:
BATTERY UNIT
Mo
del:
S
eri
al
:
BATTERY UNIT
Mod
el:
Ser
i
al:
BATTERY UNIT
Mod
el:
S
eri
al
:
BATTERY UNIT
M
o
d
el
:
S
er
ia
l:
BATTERY UNIT
M
o
de
l:
Se
r
ial:
BATTERY UNIT
Mo
d
el:
S
e
rial
:
BATTERY UNIT
M
o
d
el:
Se
r
ial:
BATTERY UNIT
M
o
d
el:
S
er
ia
l:
BATTERY UNIT
M
o
del:
Seria
l:
BATTERY UNIT
M
o
d
el:
Serial
:
BATTERY UNIT
M
o
d
el:
S
er
ial:
BATTERY UNIT
Mode
l:
S
e
r
ial
:
BATTERY UNIT
M
o
del:
S
eri
al
:
BATTERY UNIT
Mod
e
l:
S
e
rial
:
BATTERY UNIT
Mo
del:
S
er
i
a
l:
BATTERY UNIT
M
o
de
l
:
S
eri
al
:
BATTERY UNIT
Mod
e
l:
S
eri
a
l
:
BATTERY UNIT
Model
:
S
e
rial:
BATTERY UNIT
M
o
del:
Seria
l:
BATTERY UNIT
M
o
del:
S
e
rial:
BATTERY UNIT
Model
:
S
eri
a
l:
BATTERY UNIT
M
od
e
l
:
S
eri
a
l:
BATTERY UNIT
Model:
S
e
rial:
BATTERY UNIT
M
o
de
l
:
S
e
rial:
BATTERY UNIT
Model:
S
e
ri
al
:
BATTE
RY UNIT
Model:
Serial:
BATTERY UNIT
Model:
Serial:
BATTERY UNIT
M
od
e
l
:
Serial:
BATTERY UNIT
M
odel
:
Serial:
BATTERY UNIT
M
ode
l
:
Serial
:
BATTERY UNIT
Model
:
Seria
l
:
BATTERY UNIT
M
o
d
e
l
:
Seria
l
:
BATTERY UNIT
M
o
d
e
l
:
S
er
i
a
l:
BATTERY UNIT



UPSXR
CAUTION!
Wait until you are ready to power up the system before installing Battery Modules in the
UPS. Failure to do so can result in a deep discharge of the batteries and cause permanent
damage. The time from the battery installation time till the UPS is powered up should
not exceed 72 hours or 3 days.