User Manual
SPECIFICATION
Product PS 2 VGA KVM Extender
Model KVM-1-E KVM-1-R
Transmitter Receiver
Control End Display (monitor) HDB-15 (Female) HDB-15 (Female)
Keyboard PS 2
Mouse
PC End
Display (monitor) Integrated HDB-15
(Male)
N/A
Keyboard
Mouse
Speaker
Adjustments Gain x 1, Focus x 1
Maximum Resolution 2048 x 1536 @ 60Hz
Maximum Distance 1000 ft (300 m)
Power PS2 AC 7.5 1000 mA
Dimension 113 x 62 x 29 mm 113 x 62 x 29 mm
PS 2
CAUTION
1. Please read this manual prior to installation
2. Use recommended cables to achieve optimal results
3. When dealing with 3 phase power, please make sure the
PC, monitor are connected to the same phase.
4. PC and monitor should be on the same ground
INSTALLATION AND OPERATION
STEP 1: Installing the Transmitter
1. For first time installation, please turn the power off on
the PC
2. Connect the combo cable to the appropriate ports on the
PC
3. Connect the VGA/DVI connector to the PC in port of the
Transmitter
4. Connector the local monitor and speaker to VGA/DVI out
and Audio out
5. The transmitter is powered by the USB/PS2 connector
on the combo cable. If your PC does not provide appro-
priate power from the USB port, then you will need to
purchase the optional 5V power supply
6. When the transmitter is receiving appropriate power, the
yellow LED on the System Link RJ-45 connector will be
on (without flashing).
7. Turn on the PC, the green light on the System Link RJ-45
connector will be on (without flashing), when proper
VGA single is received.
8. The local monitor and speaker should also be working
properly.
STEP 2: Installing the Receiver
1. Place the receiver in the proper location
2. For optimal result, Apantac recommends Belden
1700A, Belden 1752A, Belden 1872A, Belden
7989R, Belden 2988R or similar cables.
3. Connect the keyboard and mouse on the front of the
receiver
4. Plug in the power supply
5. When the Transmitter is receiving appropriate power, the
yellow LED on the System Link RJ-45 connector will be
on (without flashing).
6. Connect the VGA/DVI to the appropriate inputs of the
receiver
STEP 3: Connect the CATx UTP cable
1. Connecting the CATx cable
2. The CATx UTP should comply with 568B.
3. Connect the UTP cable to both the transmitter and re-
ceiver’s System Link RJ-45 port.
4. The Green LED should be lit, when proper link is estab-
lished.
STEP 4: Final STEP
1. You should now be able to operate the keyboard and
mouse remotely.
2. To optimize the image quality, Focus/Gain/Equalizer can
be adjusted.
Product USB VGA KVM Extender
Model KVM-1-Eu KVM-1-Ru
Transmitter Receiver
Control End Display (monitor) HDB-15 (Female) HDB-15 (Female)
Keyboard USB Type A (Female)
Mouse
Speaker 3.5 mm Jack 3.5 mm Jack
PC End Display (monitor) Integrated HDB-15
(Male)
N/A
Keyboard
Mouse
Speaker
Adjustments Gain x 1, Focus x 1
Maximum Resolution 2048 x 1536 @ 60Hz
Maximum Distance 1000 ft (300 m)
Power 5V, 1000 mA from USB 5V, 1000 mA
Dimension 113 x 62 x 29 mm 113 x 62 x 29 mm
USB Type A (Female)
Product USB DVI KVM Extender
Model KVM-1-ED KVM-1-RD
Transmitter Receiver
Control End Display (monitor) DVI-D DVI-D
Keyboard USB Type A (Female)
Mouse
Speaker 3.5 mm Jack 3.5 mm Jack
PC End Display (monitor) Integrated DVI-D +
USB + Audio
N/A
Keyboard
Mouse
Speaker
Adjustments Equalizer
Maximum Resolution 1920x1200 @ 60Hz
Maximum Distance 115 ft (35 m)
Power 5V, 1000 mA from USB 5V, 1000 mA
Dimension 113 x 62 x 29 mm 113 x 62 x 29 mm
USB Type A (Female)
Apantac LLC
7556 SW Bridgeport Road
Portland, OR 97224
T: 503 616 3711
F: 503 389 7921
E: info@apantac.com
W: www.apantac.com