Instruction manual

14
OPERATING GUIDELINES
D.SOLDERINGIRON
1. Connect the Soldering Iron connection assembly to the 6pin
receptacle located at the front of the control panel (“9” from the
CONTROLPANELGUIDE).
2. Followtheinitialprocedures(“A.INITIALPROCEDURES”).
3. Connect the vacuum tube to the Smoke Absorber Terminal or
Vacuum Cap (“7” from the control panel). If smoke absorber
functionistobeused.
4. Activate the “SOLDER IRON” Activation switch (“14” from control
panel).Thiswill automaticallystartto increasethetemperatureof
thesolderingironto350°C(default).
5. AdjustthesolderingirontemperatureusingtheSOLDER/DESOLDER
TEMPERATUREADJUSTMENTbuttons(“4”fromthecontrolpanel).
6. If smoke absorber function is to be used. Activate the “SMOKE
ABSORBER”Activationswitch(“15”fromthecontrolpanel).
7. Start using the soldering iron as soon as desired temperature is
reached.
8. Whenthetaskisfinished,deactivatetheSMOKEABSORBERswitch.
9. DeactivatetheSOLDERIRONactivationswitch.
10. Allow sufficient time for the soldering iron to cool down before
keepinginasafestorage.
D.DESOLDERINGGUN
1. Connect the Desoldering gun connection assembly to the 6pin
receptacle located at the front of the control panel (“8” from the
CONTROLPANELGUIDE).
2. Followtheinitialprocedures(“A.INITIALPROCEDURES”).
3. Connect the vacuum tube to the Smoke Absorber Terminal or
VacuumCap(“7”fromthecontrolpanel).
19
NOTES:
● Thesleepmodetimerisconfigurablebetween1and60minutes.
● Asleepmodetimervalueof“0”disablesthesleepfunction.
● SleepmodesettingsforHotAirgunissavedintothememoryand
shallremainineffectuntilitisresetornewdataisentered.
G.AutoSleepMode(SolderingIronandDesolderingGun)
The device has a builtin autosleep feature to conserve power
enhance the heaterlife.  The sleep timer can be configured to power
downthesolderingironordesolderinggunafteradefinedtime.When
insleepmodefourdashes“    “willbeshownindicatingthatitis
nowinsleepmode.Toreactivatethesolderingironordesolderinggun
simply push the its function button or its temperature adjustment
button.
ChangingSLEEPTimer(SolderingIron)
By default, the system’s sleep duration is 0 indicating the sleep
timerisdisabled.Toactivatethesleepfunctionfollowtheprocedures.
1. TurnofftheSolderingIronFunctionswitch(“14”fromthecontrol
panel).EnsurethattheDesolderingGunFunctionswitchisinthe
offposition(“12”fromthecontrolpanel).
2. Press and hold the DOWN button of the Desoldering Gun
TemperatureAdjustmentbutton(“5”fromthecontrolpanel).
3. The Soldering IronTemperatureDisplay (“14” fromthecontrol
panel).Willswitchto“000t”indicatingitisnowinthesoldering
ironsleeptimeradjustmentmode.ReleasetheDOWN buttonof
theDesolderingGunTemperatureAdjustmentbutton
4. UsetheSolderingIronTemperatureAdjustmentbuttons(“4”from
the control panel)  to increase or decrease the sleep duration.
Timer is adjustable from1 to 60 minutes,a valueof0 indicates
thatthesleeptimerfunctionisturnedoff.
5. Confirmthechangebypressingandholdingthe“DOWN”button
ofthe DesolderingGunTemperatureAdjustmentbutton(“5”from
thecontrolpanel).
AUTO SLEEP FUNCTIONS