Specification

8.66"
7.87"
3.93"
2.52"
15.748"
Instruction Manual
1、
2、
3、
There are seven steps to installing a faucet:
INSTALLATION OF BASIN FAUCET
1.First, prepare the installation tool. Check whether the parte are complete before installation.Common faucet parts
include: hose,rubber ring, etc.In addition, waterproof tape should be prepared.
2.Check if the main valve of water supply is closed.
3.Use a waterproof tape to wrap a few turns in the clockwise direction on the thread of the faucet.(This is very
important.The direction of the waterproof tape must be tangled clockwise.lf twint revrsely,it will leak, which means
that the direction of the waterproof tape winding is opposite to the direction of he faucet thread) .
4.Install the faucet following the graphic instruction below.
5.Open the main valve of the water supply, normal water can be used.
6. The thread size is 9/16,it's meets the installation needs of most American house.
7.Button is functional when water pressure is applied.
PACKING ACCESSORIES
7: Connect the inlet hose to the angle valve
according to the hot and cold mark and tighten.
Before connecting, please confirm that there is
a sealing rubber gasket in the inlet hose connector
INSTALLATION STEPS
INSTALLATION STEPS
1. Insert 1 faucet into the panel.
2. 2 Into the hole, 3 6 Rubber gasket, 4 7 Gasket,
5 8 lock nut back onto the faucet in the sequence
show on the drawing above.
2
3
1
4
5
6
7
8
3. 9 Put the fixing rubber ring into the shower
pipe 11 , Link 10 Hand shower.
9
10
11
12
4. 12 Load the gravity ball.
Cold Hot
13
14
15
5. 13 Link to double-headed tube. 6. 14 15 Connect hot and cold water pipes by logo.
8. 26"
5. 9"
8. 46"
4. 92"
2. 36"
Instruction Manual
1、
2、
3、
There are seven steps to installing a faucet:
INSTALLATION OF BASIN FAUCET
1.First, prepare the installation tool. Check whether the parte are complete before installation.Common faucet parts
include: hose,rubber ring, etc.In addition, waterproof tape should be prepared.
2.Check if the main valve of water supply is closed.
3.Use a waterproof tape to wrap a few turns in the clockwise direction on the thread of the faucet.(This is very
important.The direction of the waterproof tape must be tangled clockwise.lf twint revrsely,it will leak, which means
that the direction of the waterproof tape winding is opposite to the direction of he faucet thread) .
4.Install the faucet following the graphic instruction below.
5.Open the main valve of the water supply, normal water can be used.
6. The thread size is 9/16,it's meets the installation needs of most American house.
7.Button is functional when water pressure is applied.
PACKING ACCESSORIES
8: Connect the inlet hose to the angle valve
according to the hot and cold mark and tighten.
Before connecting, please confirm that there is
a sealing rubber gasket in the inlet hose connector
INSTALLATION STEPS
INSTALLATION STEPS
1. Make sure there are 4 mounting
holes in the panel
2. The main body on the panel 1 36 , 6 the following
installation nut into 3 4 5 , and the main body link,
lock the main body with a hexagonal spoon 2 .
10
12
11
13
9
27
28
29
3. 9 10 The main body on the panel, 14 the
following installation nut into 11 12 13 ,
and the main link, 8 with a cross-screw on the
handle and then cover the decorative cover 7 .
24
34
35
4. 24 25
pipe 34 , Link 23 Hand shower,Lock the nut again.
Put the fixing rubber ring into the shower
Cold
Hot
32
31
30
5. 35 Load the gravity ball. 6. 32 33 Link to double-headed tube.
8. 26"
2. 36"
5. 11"
5. 51"
8. 85"
33
8
7
18
20
19
21
17
16
15
26
25
23
1
2
4
3
5
14
6
22
7. 30 31 Connect hot and cold water pipes by logo.
Instruction Manual
1、
2、
3、
There are seven steps to installing a faucet:
INSTALLATION OF BASIN FAUCET
1.First, prepare the installation tool. Check whether the parte are complete before installation.Common faucet parts
include: hose,rubber ring, etc.In addition, waterproof tape should be prepared.
2.Check if the main valve of water supply is closed.
3.Use a waterproof tape to wrap a few turns in the clockwise direction on the thread of the faucet.(This is very
important.The direction of the waterproof tape must be tangled clockwise.lf twint revrsely,it will leak, which means
that the direction of the waterproof tape winding is opposite to the direction of he faucet thread) .
4.Install the faucet following the graphic instruction below.
5.Open the main valve of the water supply, normal water can be used.
6. The thread size is 9/16,it's meets the installation needs of most American house.
7.Button is functional when water pressure is applied.
PACKING ACCESSORIES
8: Connect the inlet hose to the angle valve
according to the hot and cold mark and tighten.
Before connecting, please confirm that there is
a sealing rubber gasket in the inlet hose connector
INSTALLATION STEPS
INSTALLATION STEPS
1. Make sure there are 5 mounting holes in
the panel. 1 The main body is put into the hole,
6 the following installation nut into 2 3 4 ,
and the main body link.
4. 27 28
pipe 33 , Link 26 Hand shower,Lock the nut again.
Put the fixing rubber ring into the shower
5. 35 Load the gravity ball. 6. 37 38 39 Link to double-headed tube.
7. 35 36 Connect hot and cold water pipes by logo.
9
8
10
7
30
31
32
27
33
34
39
35
6
5
29
28
26
1
3
2
11
36
16
15
17
14
13
12
18
4
37
23
22
24
21
20
19
38
25
2. 5 7 The main body on the panel, 5 each
11 links installed，lock the main body with a
hexagonal spoon 5 ,Tighten the nut again.
3.19 21The main body on the panel, 19 each
25 links installed，lock the main body with a
hexagonal spoon 19 ,Tighten the nut again.
Cold
Hot
Hole size
36
3.11"
2.48 "
0.29 "
1.39 "
R0
.
45"
1.85 "
0.9"
7.52 "
15.8 "
R
0
.
92"
1
.
3
3"
3.29 "
1.75 "
1.24 "
1.96 "
Hole area
Hole area
Hole area
Waterfall Water
Mixed valve switch
Transfer Valve
Shower seat
Transfer Valve
Cold Hot