Specifications

118
Section 17-3
When active, data in the following format is
returned when the squelch opens:
LCnnn Vx RFnnn...n
or
LCnnn SRx RFnnn...n
or
LCnnn Mnxx RFnnn...n
When inactive, the radio returns LC data
indicating the end of the transmission as follows:
LC%nnn Vx
or
LC%nnn Vx
or
LC%nnn Vx
Notes:
1. Receive frequency and S-meter level are
output when squelch opens (range of nnn
reported by LC is 000-255 approx but varies from
set to set)
2. Response is made automatically every time
squelch opens or closes and is affected by
squelch parameters such as level and voice scan
3. Special mode (LC2) enables a continuous
stream of frequency data to be output when
squelch is open. This allows shift to next
frequency after a pre-defined delay specified by
PQ in search/scan. This also allows for high
resolution spectrum analysis.
4. Signal level values may be specified 000-255.
The AGC voltage is processed in 256 steps
internally.
Note: Refer to individual commands for details of
each field.
LM Respond with S-meter reading
To read: LM<CR>
Responds with a 256-level s-meter sample in
hexadecimal, LMnnm,
where nn = 00-FF and m is either “ “
(squelch open) or “%” (squelch closed)
LS Tone eliminate frequency Requires TE8200 option
To set: LSnnn (000-255) (000=off)
The following mapping is used between nnn and
tone frequency:
Tone Freq nnn Tone Freq nnn
0.4 (kHz) 0-60 2.6 (kHz) 230-235
0.6 70-110 3.0 237-240
1.0 160-170 3.4 240-245
1.4 190-200 3.8 245-248
1.8 210-220 4.2 248-250
2.2 220-230
To read: LS<CR>
Responds with LS nnn or LS+nnn (for mute on)
MA List a block of ten memory channels
To read: MA<CR> or MAn<CR>
(n= bank A-J or a-j)
Example:
MA
MXA00 MP0 RF0101100000 ST100000 AU0 MD0 AT0 TM
MXA01 MP0 RF0460900000 ST010000 AU0 MD1 AT0 TMTest 2
MXA02 MP0 RF0085900000 ST100000 AU0 MD0 AT0 TMTest 3
MXA03 MP0 RF0085900000 ST020000 AU0 MD1 AT0 TMTest 4
MXA04 MP0 RF0085900000 ST020000 AU0 MD6 AT0 TMTest 5
MXA05 MP0 RF0085900000 ST020000 AU0 MD7 AT0 TMTest 6
MXA06 MP0 RF0085900000 ST010000 AU0 MD2 AT0 TMTest 7
MXA07 MP0 RF0085900000 ST001000 AU0 MD8 AT0 TMTest 8
MXA08 MP0 RF0085900000 ST000050 AU0 MD4 AT0 TMTest 9
MXA09 MP0 RF0085900000 ST000050 AU0 MD3 AT0 TMTest 10
Note: Refer to individual commands for details of
each field.
MC Monitor Control To set: MCn<CR>
0 normal squelch operation
1 squelch forced closed
2 squelch forced open
MD Receive mode To set: MDn<CR>
0 WFM
1 NFM
2 AM
3 USB
4 LSB
5 CW
6 SFM
7 WAM
8 NAM
To read: MD<CR>
Responds with mode value as above
MF Set Marker Frequency To read: MF<CR>
Responds with MFnnnnnnnnnn
To set: MFnnnnnnnnnn<CR>
or MFnn.nnn
Set the bandscope marker frequency
to the specified frequency
(expressed in Hz or MHz depending
on format)
Note: Maximum resolution is 10kHz
for spans 10MHz - 500kHz;
maximum resolution is 2kHz for
spans 200kHz-100kHz
MP Set memory channel as pass To set: MPn<CR>
n = 0 (pass off), n = 1 (pass on)
To read: MP<CR> (when in
memory read mode)
Note: Setting pass on a memory
channel excludes it from scans
Note: “?” is returned when not in
M.RD mode
MQ Delete bank or memory channel MQ<CR>
Deletes the current memory channel
(when in memory recall mode)
MQnn<CR>
Deletes memory channel nn
MQx%%<CR>
Deletes all memory channels from
bank x.
Note: Responds with “?” when a
memory channel is protected.
Refer to PC, WM and WP
commands
MR Recall memory channel MRxnn<CR> recalls memory channel
nn from bank x (A-J or a-j)
To read the current memory
channel: MR<CR>
Note: Responds with “?” if the
channel is blank
MS Scan mode MS<CR>
Starts scan using the current memory
bank
MSx<CR>
Starts scan using memory bank x
(A-J or a-j)
Note: to scan and report active
frequencies, see LC command
Note: Responds with “?” if the
channel is blank
MW Memory Bank resizing MWxnn<CR>
Sets number of channels in bank x to
nn (where nn=10-90)
MWx<CR>
Responds with the current
allocation for bank x:
MW x:nn y:mm
Example:
MWA
MW A:50 a:50
MW%%<CR> or MW<CR>
Responds with a list of 10
allocations
Example:
MW%%
MW A:50 TBAAOR Test
MW a:50 TBa
MW B:50 TBBAOR Test
MW b:50 TBbaer band
MW C:50 TBCham call
MW c:50 TBcair band
MW D:50 TBDrepeater