Anypos600 Point of Service Anypos600 User Manual AOPOS SYSTEMS, S.A.
Anypos600 Point of Service Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced or transmitted in any form without express written authorization from AOPOS. Disclaimer The information in this document is subject to change without notice.
Anypos600 Point of Service Federal Communications Commission (FCC) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Anypos600 Point of Service Safety information Before installing and using the Anypos, take note of the following precautions: Read all instructions carefully. Do not place the unit on an unstable surface, cart, or stand. Do not block the slots and opening on the unit, which are provided for ventilation. Do not push objects in the ventilation slots as they may touch high voltage components and result in shock and damage to the components.
Anypos600 Point of Service TABLE OF CONTENTS Chapter 1 INTRODUCTION…..................................................................1 About the Product………………………………………………...………1 Specification………………………………………….…………………..1 Unpacking the Anypos……………..………………………………...3 Checking the packaging list………………………………………………3 Identifying Components………………………………………………….4 Removing the bottom cover…………………………………………..….6 Attaching the customer display…………………………………………..
Anypos600 Point of Service CHAPTER 1 INTRODUCTION Welcome Thank you for purchasing our powerful Anypos! With this manual is to help you operate and maintain the Anypos.
Anypos600 Point of Service USB Serial port Back Panel I/O Ports 4 4 (with 5V/12V) Parallel port 1 KB/MS port 1/1 LAN port 10/100 Base-T VGA port 1 Audio jacks 1 Cash drawer port 1(share) Modem port(RJ11) 1(share) Dimension (mm) 370(l) X 280(w) X 340(h) max Weight (standard) 8.5 Kg NOTE： 1. The specification may be different depending on configurations and types. 2. Please refer to the relational documents about the options.
Anypos600 Point of Service Unpacking the Anypos The Anypos and cable accessories are packed in a cardboard carton with foam padding for protection during shipping. Carefully unpack the Anypos as the picture below. NOTE： Please keep the packing materials if you need to ship the Anypos in the future. Checking the packaging list Anypos can be fixed in Base Mounting or Wall Mounting. After you unpack the Anypos, check that the following items are included.
Anypos600 Point of Service Identifying Components This section describes the parts and connectors on the Anypos. Front-right view DESCRIPTION 1 2 3 4 5 6 7 8 9 15-inch TFT LCD and touch screen Magnet Stripe Reader ( MSR ) Power LED HDD LED IC Card LED Power button Front Line-Out jack Speaker RF card reader antenna NOTE：When you use front Line-Out jack, no voise will be out from the speakers.
Anypos600 Point of Service DESCRIPTION 1 2 3 4 5 6 7 COMBO CDROM Customer Display IC Card Reader Rear Cover Customer Display Base Bottom Cover Base Bottom Panel Ports (Anypos616) DESCRIPTION 1 PS2 mouse port 2 Parallel port (LPT) 3 DC +12V Output ＋12V 4 Modem or cash drawer port (RJ11) DK 5 10/100 NIC port1&2 6 Customer Display port (COM4) 7 PS2 keyboard port 8 COM2 9 COM1 10 VGA port 11 COM3 12 USB 1&2&3&4 13 Line-out Microphone 5 CD
Anypos600 Point of Service NOTE： 1、 Remove the bottom cover before you connect the peripherals to the bottom Connectors. The bottom panel ports may be different from others depending on the specification and types. 2、 The default setting of VFD customer display port(RJ45) is COM2 or COM4. If you want to use DB9 port instead of RJ45, the special wire is needed. Removing the bottom cover 1. Rotate the display until it’s max angle. 2.
Anypos600 Point of Service 1. Connect the customer display cable to Customer Display port on the bottom panel. 2. Secure the display with four supplied screws. Attaching the second Monitor 1. Connect the signal cord of the second monitor to the VGA port, through the hole of stand base, the power cord is the same, connect to DC +12V Output.. 2. Secure the display with four supplied screws.
Anypos600 Point of Service Adjusting display angles The main display can be tilted back from 10 degrees to 66 degrees. (See the picture below.) Connecting peripheral devices Peripheral devices such as a printer or scanner can be connected to the Anypos. Refer to the user manual of the device you are connecting for instructions on installing drivers where needed. (Anypos616) NOTE： The bottom port board may be different depending on configurations and types.
Anypos600 Point of Service Powering the Anypos on and off 1. Remove the bottom cover. Connect the power cable to the power connector on the Anypos , Connect the AC adapter to an electrical outlet.(only for External Adapter) 3. Press the power button on the underside of the display panel. The power LED turns on. To turn off the Anypos, shut down the operating system: the main power turns off automatically. 4.
Anypos600 Point of Service CHAPTER 2 BIOS SETUP UTILITY The BIOS (Basic Input and Output System) Setup Utility displays the system's configuration status and provides options to set system parameters. The parameters are stored in battery-backed-up CMOS RAM that saves this information even when the power is turned off. When the system is turned back on, the system is configured with the values found in CMOS.The following topics are described in this chapter.
Anypos600 Point of Service conflicts, making changes to the Power Management configuration, and changing the User or Supervisor password, etc. Main Screen When you start the Setup Utility, the main menu appears. See the picture below. Standard CMOS features Use this menu to set basic system configuration. Advanced BIOS Features Use this menu to set the advanced features available on your system.
Anypos600 Point of Service Disable this sequence. Disabled Default setting：USB-ZIP/ CD-ROM/HDD-0 Advanced Chipset Features This menu is used for optimizing the chipset functions. Boot Display This setting refers to the type of display being used with the system Default setting: CRT+LEP Panel Number This item is used to select the number to support LVDS panel. Default setting: 3 Integrated Peripherals Use this menu to set onboard peripherals features.
Anypos600 Point of Service ReQuests) and DMAs (Direct Memory Access). PC Health Status This section shows the status of your CPU, fan, warning for overall system status. Frequency/Voltage Control Use this menu to set DRAM voltage, DRAM clock, and DRAM timing, etc. Load Fail-Safe Defaults This option on the menu allows users to restore all the BIOS setting to the default Fail Safe values. These values are set by manufacturer to provide a minimal and stable system.
Anypos600 Point of Service CHAPTER 3 DRIVER INSTALLATION About Installation The driver utilities and software are installed by following methods: 1. Install from the CD drive. 2. Install from the USB CDROM, USB-HDD/ ZIP/FDD or Flash disk. 3. Install from internet. NOTE： If the system boots from the USB device, configure the BIOS Setup Utility first. (See the BIOS SETUP UTILITY on Chapter 2) Software Description HDD or CD contains driver utilities and software after manufactured.
Anypos600 Point of Service have to reinstall the operating system. Driver Installation of Chipset The Chipset Driver is on \DRIVERS\CHIPSET subdirectory, run SETUP.EXE and install driver on prompt, after completing installation, reboot the computer. Driver Installation of VGA The VGA Driver is on DRIVERS\VGA letter, run SETUP.EXE and install driver on prompt, after completing the installation reboot the computer. Driver Installation of Audio The Audio Driver is on your DRIVERS\AUDIO letter, run SETUP.
Anypos600 Point of Service A). If Windows start the New Hardware Wizard Choose Next. Select "Search for the best driver for your device (Recommended)" and Choose Next. When a list of search locations is displayed, place a checkmark on "Specify a location" and use Browse to select the DRIVERS\TOUCHSCREEN\SAW subdirectory on CDROM or HDD. Choose Next. Once the GeneralTouch Touchscreen USB Interface driver has been detected choose Next again. Wait while driver files are copied to your computer.
Anypos600 Point of Service CHAPTER 4 SYSTEM TESTING This chapter gives you detailed explanation of system testing functions. About Testing 1. 2. The CHECK.EXE is a test program in TOOLS subdirectory in your CD or your HDD, which is for test of the Printer, the CustDisplay, the Keyboard, the Drawer, MSR, Scanner, IC Card Reader and Ports.
Anypos600 Point of Service Ensure the printer prints the same as the typing on the screen. Return from the sub-menu press Esc. CustDisplay: Tests the customer display. Ensure the customer display shows the same numbers and characters as input on prompt. Return by pressing Esc. KeyBoard: Tests the keyboard, ensure the character and ASCII code displaying on the screen is the same as the key you press on prompt. Return from the sub-menu press Esc. Drawer: Tests the drawer.
Anypos600 Point of Service General User can select the controller list in the windows to do configuration for it. Tools 4 Points Calibration：It needs calibration before the touchscreen work accurately. Clear and Calibrate：To erase the 25 points calibration/linearization parameters and force user to do 4 points calibration again.
Anypos600 Point of Service Linearization：is used to compensation the touchscreen linearity. Draw Test：is used for accuracy and performance check. Setting Beep： 1) Beep On Touch: Linearization Style：Touchkit utility provides user with 9 points and 25 points calibration for linearization. Double Click Time：is used to set system double click time. Change this value will affects the double click behavior for all of the mice devices in the system.
Anypos600 Point of Service 21
Anypos600 Point of Service CHAPTER 5 Troubleshooting Often after time spent troubleshooting, the problem is traced to something as simple as a loose connection. Check the following before proceeding to the problem-specific solutions. The Power-On Self Test The Power-On Self Test (POST) runs every time you turn on or reset the computer. The POST checks memory, the mainboard, the display, the keyboard, the disk drives, and other installed options.
Anypos600 Point of Service HARD DISK(S) FAIL (10) KEYBOARD IS LOCKED OUT UNLOCK THE KEY Unable to recalibrate fixed disk. The keyboard is locked and the key-board controller is pulled low. Have the Anypos serviced. KEYBOARD ERROR OR NO KEYBOARD PRESENT A keyboard is not detected. Make sure the keyboard is attached correctly and no key is pressed during boot. MANUFACTURING POST LOOP System keeps rebooting because the keyboard controller is pulled low for testing purposes. Have the Anypos serviced.
Anypos600 Point of Service Check the cable connection. Check the mouse or keyboard with another computer to see if it works. If the same problem occurs, replace the mouse or keyboard. Otherwise, have the Anypos serviced. Check that the power cord is plugged into a working The screen is blank and you electrical outlet (and the adapter is connected to the don't hear any beeps. Anypos if there is any). Check that the power is on. (Press the power switch again for confirmation.
Anypos600 Point of Service CHAPTER 6 WARRANTY For your legal rights, AOPOS promise you offer the warranty and service according to following standard: 1. Duration of limited warranty 1 year warranty. 2. Online Service You can obtain help from AOPOS when you are unable to solve the problem. Please contact our ser and Maintenance Department for any requires. Hotline:400-708-9898. Our service engineers will provide the most efficient help, or visit our website: www.aopos.com to obtain help online. 3.
