Installation guide

1. Put the upper module on the accessory box or JIG accord the photo.
2. The Bluetooth card.
Bluetooth Assembly
3. Use the Phillips(+) screwdriver to fix the sheet metal screws (4pcs).
4. Install the Top Cover carefully to avoid scratching it.
Note:
The Concave part of the Top Cover is toward the front side.
1
4
2
3
Concave part
Note: Arrange the wire or fix it by tapes to avoid interfering
with the Riser Card slot from damaging the wire.
1. Take the upper module and chassis
module.
2. Fit the golden finger of the upper
module to the Riser Card slot of
the chassis module.
Assemble the Top Cover
Riser Card Slot
Golden finger
6. Take away the protection tube of the Antenna wire.
7. The Bluetooth module and 1pcs BT screw.
Screw size: M2*L4.6 (Torque: 1.0 ² 0.1 Kgf. cm)
8. Fix the Bluetooth module on the holder of the upper module.
9. Tighten the Bluetooth module with screw.
11. The 3.3V USB connector of the main board.
Install Driver
Expansion Slot Installation
XC mini provides two miniCard slots for users to upgrade this PC
functions. Now, the miniCard can have digital TV Tuner and
Wireless LAN miniCard Module …etc. for expansion.
miniCard slot
(suggest to assemble
the TV Tuner Module)
miniCard slot
(suggest to assemble
the Wireless Module)
Antenna Hole (suggest to
assemble the Wireless antenna)
Antenna Hole (suggest to
assemble the TV Tuner antenna)
1. Remove the metal cover of the antenna hole by the screw driver.
2. Install the antenna wire into the Antenna hole of rear panel.
Metal cover
3. Use the screw driver to detach the miniCard screw of mainboard.
4. Arrange the wireless LAN wire or TV Tuner wire under the
miniCard module.
5. Insert the miniCard module and fix it with the miniCard screw.
6. Buckle the Antenna wire on the miniCard module and arrange the
wire.
7. Install the antenna.
2. Use the Phillips(+) screwdriver to detach the HDD screw.
Remove the existing HDD from the upper module.
Upgrade / Installing hard disk drive
1
4
3
2
6. Connect the Riser Card with the connector of the ODD
drive and HDD.
7. Use the Phillips(+) screwdriver to tighten two screws to fix
Riser Card with ODD drive and HDD.
NoteǺAvoid scratching the golden finger of the Riser Card.
1. Take the upper module. Use the Phillips(+) screwdriver to detach
the Riser Card screws and disassemble the Riser Card.
3. Install the new HDD into the upper module.
4. The hard disk device has to be fixed to the white plastic fixture
with four HDD screws.
5. The operation order is screw 1-2-3-4
3
2
1
4
1
3
2
4
Security lock
Dual Display Arrangement
LCD Monitor
Support DVI
CRT Monitor
Support VGA
DVI to DVI + DVI to DVI +
VGA CableVGA Cable
(MP45-DR only)
Rear Panel Connections
Projector
CRT Monitor
DVI to
VGA & DVI
Adapter
(MP45-DR
only)
LCD Monitor
TV Tuner Antenna hole
Line in (S/PDIF out)
Line out
Microphone (MIC)
Wall Outlet
Internet
DSL (Cable) Modem
USB 2.0 Port
Expander (USB HUB)
PDA
Card reader/Flash memory
Web camera
Joystick
Mouse/Keyboard
FAX/Scanner/Printer
Bluetooth Dongo
Wireless Lan Card
USB TV Tuner BOX
USB HDD
eSATA Port
Antenna wire
Golden Finger
SATA HDD
Connector
ODD
Connector
Riser Card
3. The Antenna wire of the Bluetooth card.
4. The Antenna wire was fixed into the wire clip.
5. Take away the Antenna from the wire clip.
Bluetooth Module
Antenna wire
Wire chip
Wire chip
Antenna wire Protection tube
Bluetooth
screw
Note:
The 4 pin 5VUSB connector don’t install the 3.3V
Bluetooth module
4 pin 5V USB connector
4 pin 3.3V USB connector
(to 3.3V Bluetooth)
HDMI TV
Wireless 802.11 Antenna hole
BIOS Setup
Bluetooth Cable
12. Plug the Bluetooth cable with the connector of the main board.
14. Plug the Bluetooth cable with the connector of the Bluetooth card.
15. Buckle the Bluetooth card with the Antenna wire and arrange
the wire accord the photo.
DVI to HDMI Connector
(by Territory)
After finishing the setting of
connect correct cable, power on
and enter the BIOS Setup
screen, then press <DEL>
during POST (Power On Self
Test). Choose "Load Optimized
Defaults" for recommended
optimal performance.
Before the Windows Vista/XP
are installed, please select your
ODD name : Advanced BIOS
Features > First Boot Device to
ODD name. ex. P1-
MATSHITADVD.
BIOS Setup when 1st Power On
Select ODD name if installing the Windows Vista/XP via ODD
You can use the autorun menu of Bonus CD disc. Choose the utility
and driver from the icons at left side, and then click on the "GO"
button to complete installation automatically.
Install
Driver
Install
Utility
Browse CD
Contents
Readme
Exit CD
4. Press <S> after "S=Specify Additional Device" appears.
5. Use the arrow keys to select "Intel(R) ICH9M-E/M SATA AHCI
Controller".
6. After the SATA driver installation is completed, you can proceed
with the Windows XP installation.
The following details regarding the eSATA drivers installation with
Windows XP.
1. Prepare USB FDD Device , 3.5" FDD Diskette and Driver CD.
2. Copy eSATA driver into 3.5"FDD Diskette from Driver CD.
3. Boot from the Windows XP setup disk. Press <F6> after the
message "Press F6 if you need to install a third party SCSI of
RAID driver" appears.
USB FDD
Device
3.5" FDD
Diskette
Please prepare:
Note2:
If you don't have FDD device, you
must set SATA mode to IDE mode,
but the external HDD can not
support HOT PLUG.
1. Turn on your computer. Press
<Del> to enter BIOS setup.
2. Set OnChip IDE mode >
SATA mode to IDE.
3. Save and exit BIOS Setup.
Install eSATA when the Windows XP are installed
Note1:
If installing under Windows
Vista OS, it doesn't have to
do anything for setting.
For 3.3V Bluetooth