Installation guide

ManualsBrandsAOpen ManualsComputer equipmentXC Mini MP45-DR

AOpen reserves the right to revise all the

specifications and information contained in this

document, which are subject to change without notice.

Part No.: 49.MB401.A110

Doc. No.: MP45DR-EG-E0807B

Accessories List

Screw of SATA

Card (2pcs)

Riser Card

90W DC 20V

Power Adapter

S/PDIF

Converter

(by Territory)

Power Cord

Driver CD

EIG

Power DVD

V.7.0

Option

NTI Media

Maker

Option

DVI to DVI+VGA

Y Cable

DVI to VGA

Converter

(MP45-DR only)

(MP45-D/MP45-DU)

Mainboard Overview

Intel PCIe Gigabit

LAN Chip

Realtek HD Audio Codec

Socket P Support

Intel Core 2 Duo /

Celeron Processor

CPU’s Power

Consumption ɩ35W

Intel GM45 Chipset

CPUFAN Connector

Front Panel Connector

Dual Channel Mode,

SODIMM x 2

DDRII 667/800

Max. 4GB

USB2.0 Connector x 1

IR Receiver Connector x 1

Riser Card

Connector

miniCard slot x 1

(for TV Tuner Module)

Rear Panel

Battery

miniCard slot x 1

(for Wireless Module)

Intel ICH9M Chipset

(MP45-DR only)

Screw of

Bluetooth (1pcs)

Optional Expansion Items

(by Territory)

DVI to HDMI

Converter

Screw of HDD

(4pcs)

Remote Control

3.3V USB 2.0 Connector x 1

(for 3.3V Bluetooth Module)

USB2.0 Port x 2

DVI to DVI +

D-Sub Cable

DVI to HDMI Cable

TV Tuner Kit (ATSC) TV Tuner Kit (DVB-T) Wireless Kit

Bluetooth Kit Wireless Antenna

802.11 b/g

Wireless 802.11n

Antenna

DIO Connector x 1

Easy Installation Guide

LPC Connector x 1

BIOS

30mm

Note:

There is one cable connected to

board. Please keep it connected.

If you remove it by accident,

please connect it again.

6. Use the Slotted(-) screwdriver to turn CPU socket screw toward

the Lock mark. (Clockwise direction)

7. Fit the CPU Cooler into their respective holes of the mainboard

and use the Phillips(+) screwdriver to tighten screw 1-2-3-4-5-6.

make sure the CPU Cooler is fastened to the mainboard evenly.

Lock

Note: When screw the socket. You will hear a slight sound

"Dock". That means you already installed CPU successfully.

1. Take the chassis Module. Use the rib of fan duct to detach the

fan duct.

2. Detach 6 screws of the CPU Cooler by the Phillips(+) screwdriver.

The sequence of operationis 1-2-3-4-5-6.

3. Move over the CPU Cooler carefully. Avoid damaging the

component of the mainboard.

4. Use the Slotted(-) screwdriver to turn CPU socket screw toward

the unlock mark. (Anticlockwise direction)

Note: If you do not match the CPU Socket Pin1 and CPU Golden arrow well,

you may damage the CPU.

5. Remove existing CPU, then install new CPU.

Locate Pin 1 in the socket and look for a golden arrow on the

CPU upper interface. Match Pin 1 and golden arrow. Then

insert the CPU into the socket.

Upgrade / Install CPU

Unlock

Socket Pin1Golden Arrow

UnlockLock

Socket Screw Socket Pin1

CPU Frequency Table

Note: With CPU speed changing rapidly, there might be faster CPU on the

market by the time you received this installation guide.

This table is kindly for your references only.

Core 2 Duo T9400

45nm

2.53 GHz

1066 MHz

6MB

* GM45 support front side BUS 667/800/1066MHz.

This socket supports FCPGA6 package CPU (Socket P), which is the

latest Core 2 Duo (Penryn) package developed by Intel.

Please don’t put the other CPU.

1. Disassemble the Top Cover carefully to avoid

scratching the Top Cover.

2. Use the Phillips(+) screwdriver to detach the sheet

metal screws (4pcs).

3. Disassemble the product to two modules (Upper module and

Chassis module).

Disassemble XC mini

Rear

Top Cover

Front

Top Cover

(Upper module) (Chassis module)

From R1.00

Core 2 Duo T9600

45nm

2.80 GHz

1066 MHz

6MB

SODIMM slots are designed in high and low positions which are

very easy to recognize. Insert the module straight down to the

SODIMM slot with fingers and press down firmly until the SODIMM

module is securely in place.

2. Put the memory module with correct direction. Notice there's

one key position to make sure direction is correct.

3. Plug in memory module into SODIMM slot with angle 20 ~ 30Ą.

Make sure memory module plug into slot completely.

4. User finger to push memory module vertically until the tabs lock

memory module tightly. Now, the memory modules have been

plugged properly with horizontal flat.

Upgrade / Install Memory Modules

Tab

1. There're tabs which located in the side of SODIMM holder.

Detach the existing memory from the memory slot.

Key

8. Install the Fan Duct Vertically.

Core 2 Duo P8600

45nm

2.4 GHz

1066 MHz

3MB

From R1.00

Core 2 Duo P9500

45nm

2.53 GHz

1066 MHz

6MB

From R1.00

Core 2 Duo P8400

45nm

2.26 GHz

1066 MHz

3MB

Processor Number Architecture Clock Speed Front Side Bus L2 Cache

Support BIOS

Version

Intel Core 2 Duo (Penryn) CPU

DVI-I Port

USB 2.0 Ports

RJ45 LAN Jack

20V DC Jack

TV Tuner

Antenna hole

Security Lock

Line in

(S/PDIF Out)

Line Out

Microphone

Wireless 802.11

Antenna hole

eSATA Port

HDD indicator

USB 2.0 Ports

DVD Eject Button

Power Button

Power indicator

Optical Device Drive

IR indicator (MP45-DR only)

Rib

Fan Duct

CPU Cooler

Rib

Fan Duct

CPU Cooler

Summary of content (2 pages)

PAGE 1
Accessories List Upgrade / Install CPU Mainboard Overview Rear Panel Riser Card Connector DIO Connector x 1 Battery Easy Installation Guide EIG Power DVD V.7.0 Driver CD NTI Media Maker Option Riser Card Option Socket P Support Intel Core 2 Duo / Celeron Processor CPU’s Power Consumption ɩ35W miniCard slot x 1 (for TV Tuner Module) LPC Connector x 1 Dual Channel Mode, SODIMM x 2 DDRII 667/800 Max.
PAGE 2
Upgrade / Installing hard disk drive 1. Take the upper module. Use the Phillips(+) screwdriver to detach the Riser Card screws and disassemble the Riser Card. ODD Connector XC mini provides two miniCard slots for users to upgrade this PC functions. Now, the miniCard can have digital TV Tuner and Wireless LAN miniCard Module …etc. for expansion. 1. Put the upper module on the accessory box or JIG accord the photo. 2. The Bluetooth card.