OTHERBOARD м х б в шж % n 8 d k 1юшйаН0шй@£т © ш М ш Manual CD Included ШИрт Component Solutions
Quick Installation Guide Overview Note: This Quick Installation Guide is only for quick reference. For more information, please refer to the online User's manual in the A Open Bonus Pack CD disc. Specification: CPU Chipset Architecture Cache Memory BIOS Onboard I/O Board Size Intel Pentium II / Pentium III / Celeron CPU. Intel 82440 ZX/BX AGPset. ISA x 1, PCI x 3 and AGP x 1 On the CPU card. SDRAM, DIMM x 3, maximum 512MB. Award Plua-and-Plav. 2M bit Flash ROM BIOS.
AOpen MX6B EZ Jumper and Connector Locations: MODEM-CN CD-IN CniFANl m Ef WOM JPM Back Panel: PS/2 Mouse t PS/2 Keyboard Г COM1 Jumpers: JP14: JP23 JP28 Clear CMOS AGP Ratio Keyboard/Mouse Wake Up Onboard Connectors: PWR2: FDC: IDE1: IDE2: CPUFAN1: FAN1: IrDA: PANEL: CD-IN: MODEM-CN: WOM: WOL: ATX power connector Floppy drive connector IDE1 primary channel IDE2 secondary channel CPU Fan connector Housing Fan connector IrDA (Infrared) connector Front panel (Multifunction) connector CD-audio conne
Quick Installation Guide Hardware installation Please follow the steps below to configure your motherboard. 1. Plugging CPU and Connecting C P U F a n — I ' l — 1 ' U LI Plug in the fan cable to the 3-pin CPUFAN1 or FAN1 connector. Both of these two fan connectors support hardware monitoring function, however, you can only use the CPU FAN connector to control the fan power ON/OFF. 2. Setting AGP Frequency According to the CPU you use, 66MHz AGP frequency is automatically determined by chipset.
AOpen MX6B EZ 4. Plug memory module and FDC and IDE cables. Be careful of the pin1 orientation. Wrong orientation may cause system damage. Please refer to the diagram on page 2. The DIMM types supported are SDRAM (Synchronous DRAM) only. This motherboard has three 168 pin DIMM sockets (Dual-in-line Memory Module) that allow you to install system memory up to 512MB. In case you install SDRAMs on DIMM2 and DIMM3 at the same time, it is crucial to identify single/double side.
Quick Installation Guide Celeron Celeron Celeron Celeron Celeron Celeron Celeron Celeron Celeron Celeron 266 300 300A 333 366 400 433 466 500 CPU Core Frequency Ratio External Bus Clock 266MHz= 300МНг= 300MHz= 333MHz= 366MHz= 400MHz= 433MHzr= 466MHz^ 500MHz= 4x 4.5x 4.5x 5x 5.5x 6x 6.5x 7x 7.5x 66MHz 66MHz 66MHz 66MHz 66MHz 66MHz 66MHz 66MHz 66MHz • Tip: If your system hangs or fails to boot because of over-clocking, simply use key to restore to the default setting (233MHz).
AOpen MX6B EZ The following sections are not a must to install this motherboard, they are list here for your reference. Eliminate "?" Marks in Win95 Win95 can not recognize this chipset, because it was released before Intel 440ZX/BX. You can run AOchip.exe from AOpen Bonus Pack to eliminate the "?" marks. installing Bus Master IDE Driver There is no need to install Bus Master IDE driver to support Ultra DMA/33 hard disk. If you need this driver, you can find it in the AOpen Bonus Pack CD disc or our web.
Quick Installation Guide 4. 5. Return JP14 to its normal setting by shorting pins 1-2. Connect ATX power cable back to connector PWR2. Hardware Monitoring You can install Hardware Monitoring Utility to monitor CPU temperature, fans and system voltage, etc. For more information, please see the online manual in AOpen Bonus Pack CD disc.
AOpen MX6B EZ Troubleshooting If you encounter any trouble to boot your system, follow the procedures accordingly to resolve the problem.
Quick Installation Guide Technical Support Dear Customers: Thanks of choosing AOpen products. Provide best and fast service to our customer is our first priority, but we receive numerous emails and phone calls worldwide everyday, it is very hard for us to serve everyone on time. We recommend you follow below procedures to seek help before contact us. With your help, we can then continue to provide the best quality service to more customers.
