User Guide
Table Of Contents
- MX46LS
- Hardware Installation
- About “Optional” and “Upgrade Optional”…
- JP14 Clear CMOS Data
- CPU Installation
- CPU Jumper-less Design
- CPU and System Fan Connector (with H/W Monitoring)
- JP28 USB Keyboard / Mouse Wakeup
- DIMM Sockets
- Front Panel Connector
- ATX Power Connector
- AC Power Auto Recovery
- IDE and Floppy Connector
- IrDA Connector
- AGP (Accelerated Graphic Port) Expansion Slot
- WOM (Zero Voltage Wake on Modem) Connector
- WOM by External BOX Modem
- WOM by Internal Modem Card
- WOL (Wake on LAN)
- Support 10/100 Mbps LAN onboard
- CNR (Communication and Network Riser) Expansion Slot
- PC99 Color Coded Back Panel
- Support 3 USB Ports
- CD Audio Connector
- Modem Audio Connector
- Front Audio Connector
- Dr. LED Connector (Upgrade Optional)
- Battery-less and Long Life Design
- Over-current Protection
- Hardware Monitoring
- Resettable Fuse
- 1500μF Low ESR Capacitor
- Layout (Frequency Isolation Wall)
- Pure Aluminum Heatsink
- Driver and Utility
- AWARD BIOS
- Overclocking
- Glossary
- AC97
- ACPI (Advanced Configuration & Power Interface)
- AGP (Accelerated Graphic Port)
- AMR (Audio/Modem Riser)
- Bonus Pack CD
- APM (Advanced Power Management)
- ATA (AT Attachment)
- ATA/66
- ATA/100
- BIOS (Basic Input/Output System)
- Bus Master IDE (DMA mode)
- CNR (Communication and Networking Riser)
- CODEC (Coding and Decoding)
- DDR (Double Data Rated) SDRAM
- DIMM (Dual In Line Memory Module)
- DMA (Direct Memory Access)
- ECC (Error Checking and Correction)
- EDO (Extended Data Output) Memory
- EEPROM (Electronic Erasable Programmable ROM)
- EPROM (Erasable Programmable ROM)
- EV6 Bus
- FCC DoC (Declaration of Conformity)
- FC-PGA (Flip Chip-Pin Grid Array)
- Flash ROM
- FSB (Front Side Bus) Clock
- I2C Bus
- IEEE 1394
- Parity Bit
- PBSRAM (Pipelined Burst SRAM)
- PC-100 DIMM
- PC-133 DIMM
- PC-1600 or PC-2100 DDR DRAM
- PCI (Peripheral Component Interface) Bus
- PDF Format
- PnP (Plug and Play)
- POST (Power-On Self Test)
- RDRAM (Rambus DRAM)
- RIMM (Rambus Inline Memory Module)
- SDRAM (Synchronous DRAM)
- Shadow E2PROM
- SIMM (Single In Line Memory Module)
- SMBus (System Management Bus)
- SPD (Serial Presence Detect)
- Ultra DMA
- USB (Universal Serial Bus)
- VCM (Virtual Channel Memory)
- ZIP file
- Troubleshooting
- Technical Support
- Product Registration
- How to Contact Us
M
M
X
X
4
4
6
6
L
L
S
S
O
O
n
n
l
l
i
i
n
n
e
e
M
M
a
a
n
n
u
u
a
a
l
l
Dr. LED is a CD disc storage box with 8 LEDs on its front panel, the size of Dr. LED is exactly the same as 5.25 in floppy drive, so that it
can be mount into normal 5.25 in drive bay of any housing.
Boot O.K.
KB HDD
Floppy
CPU Video
01234567
PCI Memory
The total 8 LEDs light up alternatively if the system fails in one of eight stages. Once the LED7 (latest LED) is lit, this indicates that the
system has completed its boot-up procedure.
The 8 LEDs indicate the following messages when lit:
LED 0 - Indicates that the CPU may have been installed incorrectly or is damaged.
LED 1 - Indicates that the memory may have been installed incorrectly or is damaged.
LED 2 - Indicates that the AGP may have been installed incorrectly or is damaged.
LED 3 - Indicates that the PCI card may have been installed incorrectly or is damaged.
LED 4 - Indicates that the floppy disk drive may have been installed incorrectly or is damaged.
LED 5 - Indicates that the HDD may have been installed incorrectly or is damaged.
LED 6 - Indicates that the keyboard may have been installed incorrectly or is damaged.
LED 7 - Indicates that the system is OK.
Note: During POST (Power On Self Test) procedure, the Debug
LED will light on sequentially from LED0 to LED7 until the system
boot O.K
49