Specifications
Table Of Contents
- MX3W-E3 / MX3W-V3
- Hardware Installation
- About “Optional” and “Upgrade Optional”…
- Clear CMOS Data
- CPU Installation
- JP23 Adjust FSB/PCI Clock Ratio
- CPU Jumper-less Design
- CPU and Housing Fan Connector (with H/W Monitoring)
- DIMM Socket
- Front Panel Connector
- ATX Power Connector
- JP28 Keyboard/Mouse Wake-up
- Power and RAM Power Indicate LED
- AC Power Auto Recovery
- IDE and Floppy Connector
- IrDA Connector
- WOM (Zero Voltage Wake on Modem) Connector
- WOL (Wake on LAN)
- CNR (Communication and Network Riser) Expansion Slot
- Support IntelR PRO/100 Network Connection (Optional)
- JP13 LAN Enable / Disable Select Jumper (Optional)
- PC99 Color Coded Back Panel
- COM2 Connector
- Support 2nd USB Port
- DVO (Digital Video Out) Connector
- Chassis Intrusion Sensor
- CD Audio Connector
- Modem Audio Connector
- AUX-IN Connector
- Front Audio Connector
- GPO (General Purpose Output) Connector
- Over-current Protection
- Hardware Monitoring
- Resettable Fuse
- Low ESR Capacitor
- Layout (Frequency Isolation Wall)
- Driver and Utility
- AWARD BIOS
- Overclocking
- Glossary
- AC97
- ACPI (Advanced Configuration & Power Interface)
- AGP (Accelerated Graphic Port)
- AMR (Audio/Modem Riser)
- AOpen Bonus Pack CD
- APM (Advanced Power Management)
- ATA (AT Attachment)
- ATA/66
- ATA/100
- BIOS (Basic Input/Output System)
- Bus Master IDE (DMA mode)
- CNR (Communication and Networking Riser)
- CODEC (Coding and Decoding)
- DDR (Double Data Rated) SDRAM
- DIMM (Dual In Line Memory Module)
- DMA (Direct Memory Access)
- ECC (Error Checking and Correction)
- EDO (Extended Data Output) Memory
- EEPROM (Electronic Erasable Programmable ROM)
- EPROM (Erasable Programmable ROM)
- EV6 Bus
- FCC DoC (Declaration of Conformity)
- FC-PGA (Flip Chip-Pin Grid Array)
- Flash ROM
- FSB (Front Side Bus) Clock
- I2C Bus
- IEEE 1394
- Parity Bit
- PBSRAM (Pipelined Burst SRAM)
- PC-100 DIMM
- PC-133 DIMM
- PC-1600 or PC-2100 DDR DRAM
- PCI (Peripheral Component Interface) Bus
- PDF Format
- PnP (Plug and Play)
- POST (Power-On Self Test)
- RDRAM (Rambus DRAM)
- RIMM (Rambus Inline Memory Module)
- SDRAM (Synchronous DRAM)
- Shadow E2PROM
- SIMM (Single In Line Memory Module)
- SMBus (System Management Bus)
- SPD (Serial Presence Detect)
- Ultra DMA
- USB (Universal Serial Bus)
- VCM (Virtual Channel Memory)
- ZIP file
- Troubleshooting
- Technical Support
- Product Registration
- How to Contact Us

M
M
X
X
3
3
W
W
-
-
E
E
3
3
/
/
M
M
X
X
3
3
W
W
-
-
V
V
3
3
O
O
n
n
l
l
i
i
n
n
e
e
M
M
a
a
n
n
u
u
a
a
l
l
Battery-less and Long Life Design
This Motherboard implements Flash ROM and a special circuit that allows you to save your current CPU and CMOS Setup
configurations without the need of a battery. The RTC (real time clock) can also keep running as long as the power cord is
plugged. If you lose your CMOS data by accident, you can just reload the CMOS configurations from Flash ROM and the system
will recover as usual.
ATX Stand-by Power Battery
Backup by EEPROM
Auto Switch
RTC
(Real Time Clock)
00:00:00
Flash
ROM
CMOS
A
uto switching to ATX standby
power as long as AC power line is
plugged. This smart design
increases battery life if you still plug
battery on motherboard.
58