Specifications
Table Of Contents
- MX3W-E3 / MX3W-V3
- Hardware Installation
- About “Optional” and “Upgrade Optional”…
- Clear CMOS Data
- CPU Installation
- JP23 Adjust FSB/PCI Clock Ratio
- CPU Jumper-less Design
- CPU and Housing Fan Connector (with H/W Monitoring)
- DIMM Socket
- Front Panel Connector
- ATX Power Connector
- JP28 Keyboard/Mouse Wake-up
- Power and RAM Power Indicate LED
- AC Power Auto Recovery
- IDE and Floppy Connector
- IrDA Connector
- WOM (Zero Voltage Wake on Modem) Connector
- WOL (Wake on LAN)
- CNR (Communication and Network Riser) Expansion Slot
- Support IntelR PRO/100 Network Connection (Optional)
- JP13 LAN Enable / Disable Select Jumper (Optional)
- PC99 Color Coded Back Panel
- COM2 Connector
- Support 2nd USB Port
- DVO (Digital Video Out) Connector
- Chassis Intrusion Sensor
- CD Audio Connector
- Modem Audio Connector
- AUX-IN Connector
- Front Audio Connector
- GPO (General Purpose Output) Connector
- Over-current Protection
- Hardware Monitoring
- Resettable Fuse
- Low ESR Capacitor
- Layout (Frequency Isolation Wall)
- Driver and Utility
- AWARD BIOS
- Overclocking
- Glossary
- AC97
- ACPI (Advanced Configuration & Power Interface)
- AGP (Accelerated Graphic Port)
- AMR (Audio/Modem Riser)
- AOpen Bonus Pack CD
- APM (Advanced Power Management)
- ATA (AT Attachment)
- ATA/66
- ATA/100
- BIOS (Basic Input/Output System)
- Bus Master IDE (DMA mode)
- CNR (Communication and Networking Riser)
- CODEC (Coding and Decoding)
- DDR (Double Data Rated) SDRAM
- DIMM (Dual In Line Memory Module)
- DMA (Direct Memory Access)
- ECC (Error Checking and Correction)
- EDO (Extended Data Output) Memory
- EEPROM (Electronic Erasable Programmable ROM)
- EPROM (Erasable Programmable ROM)
- EV6 Bus
- FCC DoC (Declaration of Conformity)
- FC-PGA (Flip Chip-Pin Grid Array)
- Flash ROM
- FSB (Front Side Bus) Clock
- I2C Bus
- IEEE 1394
- Parity Bit
- PBSRAM (Pipelined Burst SRAM)
- PC-100 DIMM
- PC-133 DIMM
- PC-1600 or PC-2100 DDR DRAM
- PCI (Peripheral Component Interface) Bus
- PDF Format
- PnP (Plug and Play)
- POST (Power-On Self Test)
- RDRAM (Rambus DRAM)
- RIMM (Rambus Inline Memory Module)
- SDRAM (Synchronous DRAM)
- Shadow E2PROM
- SIMM (Single In Line Memory Module)
- SMBus (System Management Bus)
- SPD (Serial Presence Detect)
- Ultra DMA
- USB (Universal Serial Bus)
- VCM (Virtual Channel Memory)
- ZIP file
- Troubleshooting
- Technical Support
- Product Registration
- How to Contact Us

M
M
X
X
3
3
W
W
-
-
E
E
3
3
/
/
M
M
X
X
3
3
W
W
-
-
V
V
3
3
O
O
n
n
l
l
i
i
n
n
e
e
M
M
a
a
n
n
u
u
a
a
l
l
P
P
C
C
9
9
9
9
C
C
o
o
l
l
o
o
r
r
C
C
o
o
d
d
e
e
d
d
B
B
a
a
c
c
k
k
P
P
a
a
n
n
e
e
l
l
The onboard I/O devices are PS/2 Keyboard, PS/2 Mouse, serial ports COM1 and COM2, Printer, four USB, AC97 sound and
game port. The view angle of drawing shown here is from the back panel of the housing.
PS/2 Keyboard: For standard keyboard, which is using a PS/2 plug.
PS/2 Mouse: For PC-Mouse, which is using a PS/2 plug.
USB Port: Available for connecting USB devices.
MIC-In
Line-In
Speaker Out
VGA
Connector
COM 1 Port
USB
Connectors
PS/2 Keyboard
Connector
PS/2 Mouse
Connector
SPP/EPP/ECP
Parallel Port
RJ-45 LAN
Connector(Optional)
MIDI/Game Port
Parallel Port: To connect with SPP/ECP/EPP printer.
COM1 Port: To connect with pointing devices, modem or others serial devices.
VGA Connector: To connect with PC monitor.
Speaker Out: To External Speaker, Earphone or Amplifier.
Line-In: Comes from the signal sources, such as CD/Tape player.
MIC-In: From Microphone.
MIDI/Game Port: For 15-pin PC joystick, game pad or MIDI devices.
48
RJ-45 LAN Connector: To 10/100M bps Ethernet, Ethernet RJ45 connector