Specifications
Table Of Contents
- MX3W-E3 / MX3W-V3
- Hardware Installation
- About “Optional” and “Upgrade Optional”…
- Clear CMOS Data
- CPU Installation
- JP23 Adjust FSB/PCI Clock Ratio
- CPU Jumper-less Design
- CPU and Housing Fan Connector (with H/W Monitoring)
- DIMM Socket
- Front Panel Connector
- ATX Power Connector
- JP28 Keyboard/Mouse Wake-up
- Power and RAM Power Indicate LED
- AC Power Auto Recovery
- IDE and Floppy Connector
- IrDA Connector
- WOM (Zero Voltage Wake on Modem) Connector
- WOL (Wake on LAN)
- CNR (Communication and Network Riser) Expansion Slot
- Support IntelR PRO/100 Network Connection (Optional)
- JP13 LAN Enable / Disable Select Jumper (Optional)
- PC99 Color Coded Back Panel
- COM2 Connector
- Support 2nd USB Port
- DVO (Digital Video Out) Connector
- Chassis Intrusion Sensor
- CD Audio Connector
- Modem Audio Connector
- AUX-IN Connector
- Front Audio Connector
- GPO (General Purpose Output) Connector
- Over-current Protection
- Hardware Monitoring
- Resettable Fuse
- Low ESR Capacitor
- Layout (Frequency Isolation Wall)
- Driver and Utility
- AWARD BIOS
- Overclocking
- Glossary
- AC97
- ACPI (Advanced Configuration & Power Interface)
- AGP (Accelerated Graphic Port)
- AMR (Audio/Modem Riser)
- AOpen Bonus Pack CD
- APM (Advanced Power Management)
- ATA (AT Attachment)
- ATA/66
- ATA/100
- BIOS (Basic Input/Output System)
- Bus Master IDE (DMA mode)
- CNR (Communication and Networking Riser)
- CODEC (Coding and Decoding)
- DDR (Double Data Rated) SDRAM
- DIMM (Dual In Line Memory Module)
- DMA (Direct Memory Access)
- ECC (Error Checking and Correction)
- EDO (Extended Data Output) Memory
- EEPROM (Electronic Erasable Programmable ROM)
- EPROM (Erasable Programmable ROM)
- EV6 Bus
- FCC DoC (Declaration of Conformity)
- FC-PGA (Flip Chip-Pin Grid Array)
- Flash ROM
- FSB (Front Side Bus) Clock
- I2C Bus
- IEEE 1394
- Parity Bit
- PBSRAM (Pipelined Burst SRAM)
- PC-100 DIMM
- PC-133 DIMM
- PC-1600 or PC-2100 DDR DRAM
- PCI (Peripheral Component Interface) Bus
- PDF Format
- PnP (Plug and Play)
- POST (Power-On Self Test)
- RDRAM (Rambus DRAM)
- RIMM (Rambus Inline Memory Module)
- SDRAM (Synchronous DRAM)
- Shadow E2PROM
- SIMM (Single In Line Memory Module)
- SMBus (System Management Bus)
- SPD (Serial Presence Detect)
- Ultra DMA
- USB (Universal Serial Bus)
- VCM (Virtual Channel Memory)
- ZIP file
- Troubleshooting
- Technical Support
- Product Registration
- How to Contact Us

M
M
X
X
3
3
W
W
-
-
E
E
3
3
/
/
M
M
X
X
3
3
W
W
-
-
V
V
3
3
O
O
n
n
l
l
i
i
n
n
e
e
M
M
a
a
n
n
u
u
a
a
l
l
S
S
u
u
p
p
p
p
o
o
r
r
t
t
e
e
d
d
C
C
P
P
U
U
F
F
r
r
e
e
q
q
u
u
e
e
n
n
c
c
y
y
Note: This motherboard supports CPU
auto-detection function. Therefore, you
don’t need to set CPU frequency by
manual.
Core Frequency = CPU Bus Clock * CPU Ratio
PCI Clock = CPU Bus Clock / Clock Ratio
AGP Clock = PCI Clock x 2
CPU CPU Core Frequency FSB Clock Ratio
Celeron 533 533MHz 66MHz 8x
Celeron 566 566MHz 66MHz 8.5x
Celeron 600 600MHz 66MHz 9x
Celeron 667 667MHz 66MHz 10x
Celeron 700 700MHz 66MHz 10.5
Celeron 766 766MHz 66MHz 11.5x
Celeron 800 800MHz 100MHz 8x
Celeron 900 900MHz 100MHz 9x
Celeron 1G 1GHz 100MHz 10x
Celeron 1.1G 1.1GHz 100MHz 11x
Celeron 1.2G 1.2GHz 100MHz 12x
Pentium III 800E 800MHz 100MHz 8x
Pentium III 850E 850MHz 100MHz 8.5x
27