Dell™ XPS™ M1730 Owner's Manual About Your Computer Securing Your Computer Setting Up Your Computer Cleaning Your Computer Using the Display Troubleshooting Using the Keyboard Adding and Replacing Parts Using a Battery Traveling With Your Computer Using the Camera Getting Help Using GamePanel Specifications Using Multimedia Appendix Using Cards Glossary Setting Up and Using Networks Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of
Back to Contents Page About Your Computer Dell™ XPS™ M1730 Owner's Manual Front View Left Side View Right Side View Back View Bottom View Front View 1 camera 2 display 3 power button 4 GamePanel 5 device status lights 6 right speaker 7 infrared sensor 8 media control buttons 9 touch pad 10 left speaker 11 Dell™ MediaDirect™ button 12 keyboard status lights 13 digital array microphones (2) 14 display latch 15 camera indicator camera — Built-in camera for video capture, confer
GamePanel — A small secondary LCD for displaying text and graphical information. device status lights Turns on when you turn on the computer and blinks when the computer is in a power management mode. Turns on when the computer reads or writes data. NOTICE: To avoid loss of data, never turn off the computer while the flashing. light is Turns on steadily or blinks to indicate battery charge status. Turns on when wireless devices are enabled. ® Turns on when Bluetooth wireless technology is enabled.
Turn the volume down. Play the next track. Turn the volume up. Stop. Play or pause. speakers — To adjust the volume of the integrated speakers, press the volume control buttons or mute button. Dell™ MediaDirect™ button — Press the Dell MediaDirect button to launch Dell MediaDirect (see Using Dell MediaDirect™). 1 Dell MediaDirect button keyboard status lights The blue lights located above the keyboard indicate the following: Turns on when the numeric keypad is enabled.
display latch — Keeps the display closed. camera Indicator — The indicator shows solid blue light when the camera is active and off when the camera is not. Left Side View 1 DVI-I connector (Dual link) 2 S-video connector 3 USB connector 4 IEEE 1394 connector 5 8-in-1 memory card reader 6 optical drive 7 microphone connector 8 headphone connectors (2) DVI-I Connector — Used for connecting a DVI or VGA display (through dongle). S-video connector — Connects your computer to a TV.
Attach a microphone to this connector. headphone connectors — Dual headphone connectors for attaching headphones. Attach a microphone to the connector. Attach headphones to the connectors. Right Side View 1 Express card slot 2 wireless switch 3 Wi-Fi Catcher™ Network Locator 4 USB connectors (2) 5 security cable slot ExpressCard slot — Supports one ExpressCard. The computer ships with a plastic blank installed in the slot. For more information, see ExpressCards.
The Wi-Fi Catcher Network Locator has an LED that operates as follows: ¡ ¡ ¡ ¡ Flashing blue: Searching for networks Solid blue: Strong network found Solid yellow: Weak network found Off: No signal found NOTE: The Dell Wi-Fi Catcher Network Locator light appears only when the computer is turned off and wireless networking is activated in the system setup program. USB connectors Connect USB devices, such as a mouse, keyboard, or printer.
USB connectors Connect USB devices, such as a mouse, keyboard, or printer. network connector (RJ-45) NOTICE: To avoid damaging the computer, do not plug a telephone line into the network connector. Connects the computer to a network. The two lights next to the connector indicate status and activity for wired network connections. For information on using the network adapter, see the device user's guide supplied with your computer.
air vents — The computer uses an internal fan to create airflow through the vents, which prevents the computer from overheating. CAUTION: Do not block, push objects into, or allow dust to accumulate in the air vents. Do not store your computer in a low-airflow environment, such as a closed briefcase, while it is running. Restricting the airflow can damage the computer or cause a fire.
Back to Contents Page Appendix Dell™ XPS™ M1730 Owner's Manual Overview Viewing the System Setup Screens System Setup Screens Commonly Used Options FCC Notice (U.S. Only) Macrovision Product Notice Overview NOTE: Your operating system may automatically configure most of the options available in the system setup program, thus overriding options that you set through the system setup program. (An exception is the Fn Key Emulation option, which you can disable or enable only through the system setup program.
The boot sequence, or boot order, tells the computer where to look to find the software needed to start the operating system. You can control the boot sequence and enable/disable devices using the Boot Order page of the system setup program. NOTE: To change the boot sequence on a one-time-only basis, see Performing a One-Time Boot.
l Plug the system into a different outlet so that the system and the receiver are on different branch circuits. If necessary, consult a representative of Dell Inc. or an experienced radio/television technician for additional suggestions. The following information is provided on the device or devices covered in this document in compliance with the FCC regulations: Product name: Dell™ XPS™ M1730 Model number: PP06XA Company name: Dell Inc.
Back to Contents Page Using a Battery Dell™ XPS™ M1730 Owner's Manual Battery Performance Checking the Battery Charge Conserving Battery Power Power Management Modes Configuring Power Management Settings Charging the Battery Removing the Battery Storing a Battery Battery Performance NOTE: For information about the Dell warranty for your computer, see the Product Information Guide or separate paper warranty document that shipped with your computer.
Microsoft® Windows® Battery Meter The battery meter indicates the remaining battery charge. To check the Power Meter, double-click the If the computer is connected to an electrical outlet, a icon on the taskbar. icon appears.
NOTICE: If your computer loses AC and battery power while in standby or sleep mode, it may lose data. To enter standby mode in Windows XP, click Start® Turn off computer® Stand by. To enter sleep mode in Windows Vista, click the Windows Vista Start button , and then click Sleep. NOTE: If your computer is not responding, pressing and holding the power button for more than 10 seconds turns it off.
NOTE: You can leave the battery in the computer for as long as you like. The battery's internal circuitry prevents the battery from overcharging. If the battery is hot from being used in your computer or being in a hot environment, the battery may not charge when you connect the computer to an electrical outlet. The battery is too hot to start charging if the light flashes alternately blue and orange.
Back to Contents Page Using the Camera Dell™ XPS™ M1730 Owner's Manual Accessing the Camera's Help File Manually Adjusting the Camera Settings Creating a Picture or a Video The camera is integrated in the computer display. The camera and its integrated digital microphones allow you to take photos and videos and to communicate visually and verbally with other computer users. The blue camera light appears when the camera is turned on. For more information about camera features, see Specifications.
For more information about creating pictures or videos, see the camera's Video Software Help file (see Accessing the Camera's Help File).
Back to Contents Page Using Cards Dell™ XPS™ M1730 Owner's Manual ExpressCards Memory Card Reader ExpressCards ExpressCards provide additional memory, wired and wireless communications, multimedia and security features. For example, you can add an ExpressCard to make wireless wide area network (WWAN) connectivity available on your computer.
The computer recognizes the ExpressCard and automatically loads the appropriate device driver. If the configuration program tells you to load the manufacturer's drivers, use the media that came with the ExpressCard. Removing an ExpressCard or Blank CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. Press the latch and remove the card or blank.
Memory Card Blanks Your computer shipped with a plastic blank installed in the memory card reader. Blanks protect unused slots from dust and other particles. Save the blank for use when no media memory card is installed in the slot; blanks from other computers may not fit your computer. Remove the blank before installing a media memory card. To remove the blank, see Removing a Memory Card or Blank. Installing a Memory Card You can install a media memory card in the computer while the computer is running.
Back to Contents Page Cleaning Your Computer Dell™ XPS™ M1730 Owner's Manual CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. Computer, Keyboard, and Display CAUTION: Before you clean your computer, disconnect the computer from the electrical outlet and remove any installed batteries. Clean your computer with a soft cloth dampened with water. Do not use liquid or aerosol cleaners, which may contain flammable substances.
Back to Contents Page Getting Help Dell™ XPS™ M1730 Owner's Manual Obtaining Assistance Problems With Your Order Product Information Returning Items for Warranty Repair or Credit Before You Call Contacting Dell Obtaining Assistance CAUTION: If you need to remove the computer cover, first disconnect the computer power and modem cables from all electrical outlets. If you experience a problem with your computer, you can complete the following steps to diagnose and troubleshoot the problem: 1.
www.dell.ca (Canada only) You can access Dell Support through the following websites and e-mail addresses: l Dell Support websites support.dell.com support.jp.dell.com (Japan only) support.euro.dell.com (Europe only) l Dell Support e-mail addresses mobile_support@us.dell.com support@us.dell.com la-techsupport@dell.com (Latin America and Caribbean countries only) apsupport@dell.com (Asian/Pacific countries only) l Dell Marketing and Sales e-mail addresses apmarketing@dell.
4. Include any accessories that belong with the item(s) being returned (power cables, software floppy disks, guides, and so on) if the return is for credit. 5. Pack the equipment to be returned in the original (or equivalent) packing materials. You are responsible for paying shipping expenses. You are also responsible for insuring any product returned, and you assume the risk of loss during shipment to Dell. Collect On Delivery (C.O.D.) packages are not accepted.
Back to Contents Page Using the Display Dell™ XPS™ M1730 Owner's Manual Adjusting Brightness Using a Projector Making Images and Text Look Bigger or Sharper Setting Display Resolution and Refresh Rate Adjusting Brightness When a Dell™ computer is running on battery power, you can conserve power by setting the display brightness to the lowest comfortable setting by pressing and the up- or down-arrow key on the keyboard.
1. Click the Windows Vista Start button , and click Control Panel. 2. Under Appearance and Personalization, click Adjust screen resolution. 3. In the Display Settings window, under Resolution, slide the slide bar to the left/right to decrease/increase the screen resolution. 4. Click How do I get the best display? for further instructions.
Back to Contents Page Dell™ XPS™ M1730 Owner's Manual Finding Information Finding Information NOTE: Some features or media may be optional and may not ship with your computer. Some features or media may not be available in certain countries. NOTE: Additional information may ship with your computer.
l Microsoft Windows License Label The label is located on the memory module cover at the bottom of the system. NOTE: If your operating system is Windows XP, this label might look different. NOTE: As an increased security measure,the newly designed Microsoft Windows license label incorporates a missing portion or "hole" to discourage removal of the label. l l l l l l l l l Solutions — Troubleshooting hints and tips, articles from technicians, Dell Support Website — support.dell.
After you reinstall your operating system, use the Drivers and Utilities media to reinstall drivers for the devices that came with your computer. Your operating system product key label is located on your computer. NOTE: The color of your DVD varies based on the operating system you ordered.
Back to Contents Page Using GamePanel Dell™ XPS™ M1730 Owner's Manual GamePanel Applications The Logitech® GamePanel™ is a small secondary monochrome LCD for displaying text and graphical information located at the top right hand corner of the dashboard. This shows important gaming information such as frames per second, health and so on, without cluttering the main display. It can also display non-gaming information such as memory utilization, CPU utilization, and so on.
Back to Contents Page Glossary Dell™ XPS™ M1730 Owner's Manual Terms in this Glossary are provided for informational purposes only and may or may not describe features included with your particular computer. A AC — alternating current — The form of electricity that powers your computer when you plug the AC adapter power cable in to an electrical outlet.
CD-RW — CD rewritable — A rewritable version of a CD. Data can be written to a CD-RW disc, and then erased and written over (rewritten). CD-RW drive — A drive that can read CDs and write to CD-RW (rewritable CDs) and CD-R (recordable CDs) discs. You can write to CD-RW discs multiple times, but you can write to CD-R discs only once. CD-RW/DVD drive — A drive, sometimes referred to as a combo drive, that can read CDs and DVDs and write to CD-RW (rewritable CDs) and CD-R (recordable CDs) discs.
EIDE — enhanced integrated device electronics — An improved version of the IDE interface for hard drives and CD drives. EMI — electromagnetic interference — Electrical interference caused by electromagnetic radiation. ENERGY STAR® — Environmental Protection Agency requirements that decrease the overall consumption of electricity. EPP — enhanced parallel port — A parallel connector design that provides bidirectional data transmission. ESD — electrostatic discharge — A rapid discharge of static electricity.
Hz — hertz — A unit of frequency measurement that equals 1 cycle per second. Computers and electronic devices are often measured in kilohertz (kHz), megahertz (MHz), gigahertz (GHz), or terahertz (THz). I IC — integrated circuit — A semiconductor wafer, or chip, on which thousands or millions of tiny electronic components are fabricated for use in computer, audio, and video equipment.
memory module — A small circuit board containing memory chips, which connects to the system board. MHz — megahertz — A measure of frequency that equals 1 million cycles per second. The speeds for computer processors, buses, and interfaces are often measured in MHz. Mini PCI — A standard for integrated peripheral devices with an emphasis on communications such as modems and NICs. A Mini PCI card is a small external card that is functionally equivalent to a standard PCI expansion card.
RAID — redundant array of independent disks — A method of providing data redundancy. Some common implementations of RAID include RAID 0, RAID 1, RAID 5, RAID 10, and RAID 50. RAM — random-access memory — The primary temporary storage area for program instructions and data. Any information stored in RAM is lost when you shut down your computer. readme file — A text file included with a software package or hardware product.
SXGA — super-extended graphics array — A video standard for video cards and controllers that supports resolutions up to 1280 x 1024. SXGA+ — super-extended graphics array plus — A video standard for video cards and controllers that supports resolutions up to 1400 x 1050. system board — The main circuit board in your computer. Also known as the motherboard. system setup — A utility that serves as an interface between the computer hardware and the operating system.
WLAN — wireless local area network. A series of interconnected computers that communicate with each other over the air waves using access points or wireless routers to provide Internet access. write-protected — Files or media that cannot be changed. Use write-protection when you want to protect data from being changed or destroyed. To writeprotect a 3.5-inch floppy disk, slide its write-protect tab to the open position. WWAN — wireless wide area network.
Back to Contents Page Using the Keyboard Dell™ XPS™ M1730 Owner's Manual Numeric Keypad Keyboard Illumination Key Combinations Touch Pad Numeric Keypad The numeric keypad functions like the numeric keypad on an external keyboard. l To enable the keypad, press . The l To disable the keypad, press again. light indicates that the keypad is active. Keyboard Illumination Your computer features keyboard illumination.
Windows logo key and Runs Windows Explorer. Windows logo key and Opens the Run dialog box. Windows logo key and Opens the Search Results dialog box. Windows logo key and Opens the Search Results-Computer dialog box (if the computer is connected to a network). Windows logo key and Opens the System Properties dialog box. To adjust keyboard operation, such as the character repeat rate, open the Control Panel, click Hardware and Sound, and click Keyboard.
Back to Contents Page Using Multimedia Dell™ XPS™ M1730 Owner's Manual Playing Media Playing Media Using Dell Express Card Remote Control (Optional) Copying CD, DVD, and Blu-ray Disc™ (BD) Media Adjusting the Volume Adjusting the Picture Using Dell MediaDirect™ Connecting Your Computer to a TV or Audio Device Playing Media NOTICE: Do not press down on the optical drive tray when you open or close it. Keep the tray closed when you are not using the drive.
Play. Fast forward. Pause. Fast reverse. Advance a single frame while in pause mode. Go to the next title or chapter. Continuously play the current title or chapter. Go to the previous title or chapter. Eject. For more information on playing media, click Help on the media player (if available). Playing Media Using Dell Express Card Remote Control (Optional) The Dell Express Card remote control is designed to control Dell Media Direct and Windows Vista™ Media Center.
NOTE: Ensure that you observe all copyright laws while copying media. NOTE: The types of optical drives offered by Dell may vary by country. This section applies only to computers that have a DVD+/-RW, Combo, or BD-RE drive. The following instructions explain how to make an exact copy of a CD, DVD or BD using Roxio Creator. You can also use Roxio Creator for other purposes, such as creating music CDs from audio files stored on your computer or backing up important data.
DVD-RW Yes Yes Yes DVD+R DL Yes Yes No DVD-R DL Yes No No BD-R Yes Yes No BD-RE Yes Yes Yes Helpful Tips l l Use Microsoft® Windows® Explorer to drag and drop files to a CD-R or CD-RW only after you start Roxio Creator and open a Creator project. Do not burn a blank CD-R or CD-RW to its maximum capacity; for example, do not copy a 650-MB file to a blank 650-MB CD. The CD-RW drive needs 1–2 MB of the blank space to finalize the recording.
2. Under Personalization, click Adjust Screen Resolution. The Display Properties window appears. 3. Under Resolution: click and drag the bar to reduce the resolution setting. 4. In the drop-down menu under Colors:, click Medium (16 bit). 5. Click OK. Using Dell MediaDirect™ Dell MediaDirect is an instant-on multimedia playback mode for digital media. Press the Dell MediaDirect button, located on the hinge cover, to launch Dell MediaDirect.
1 S-video TV-out connector 2 S-video connector 1 S-video TV-out connector 2 composite video adapter 3 S/PDIF digital audio connector 4 composite video-output connector 5 S-video connector 1 S-video TV-out connector 2 component video adapter 3 S/PDIF digital audio connector 4 Pr (red) component video-output connector 5 Pb (blue) component video-output connector 6 Y (green) component video-output connector If you want to connect your computer to a TV or audio device, it is recommended that you
NOTE: If your TV or audio device supports S-video but not S/PDIF digital audio, you can connect an S-video cable directly to the S-video TV-out connector on the computer (without the TV/digital audio adapter cable). 2. Plug one end of the S-video cable into the S-video output connector on the computer. 3. Plug the other end of the S-video cable into the S-video input connector on your TV. 4. Plug the single-connector end of the audio cable into the headphone connector on your computer. 5.
1 composite video adapter 2 S/PDIF digital audio cable 6. Plug the other end of the S/PDIF digital audio cable into the audio input connector on your TV or audio device. 7. Turn on the TV, turn on any audio device that you connected (if applicable), and then turn on the computer. 8. See Enabling the Display Settings for a TV to ensure that the computer recognizes and works properly with the TV.
6. Plug the two RCA connectors on the other end of the audio cable into the audio input connectors on your TV or other audio device. 7. Turn on the TV, turn on any audio device that you connected (if applicable), and then turn on the computer. 8. See Enabling the Display Settings for a TV to ensure that the computer recognizes and works properly with the TV.
1 composite video adapter 2 S/PDIF digital audio cable 6. Plug the other end of the digital audio cable into the S/PDIF input connector on your TV or other audio device. 7. Turn on the TV, turn on any audio device that you connected (if applicable), and then turn on the computer. 8. See Enabling the Display Settings for a TV to ensure that the computer recognizes and works properly with the TV.
8. See Enabling the Display Settings for a TV to ensure that the computer recognizes and works properly with the TV. Component Video and S/PDIF Digital Audio 1 S-video TV-out connector 1 component video adapter 3 standard audio cable 2 component video adapter 2 component video cable 1. Turn off the computer and the TV and/or audio device that you want to connect. 2. Connect the component video adapter to the S-video TV-out connector on the computer. 3.
1 component video adapter 2 S/PDIF digital audio cable 6. Plug the other end of the digital audio cable into the S/PDIF input connector on your TV or other audio device. 7. Turn on the TV, turn on any audio device that you connected (if applicable), and then turn on the computer. 8. See Enabling the Display Settings for a TV to ensure that the computer recognizes and works properly with the TV. Enabling S/PDIF Digital Audio 1. Double-click the speaker icon in the Windows notification area. 2.
Windows XP 1. Click the Start button, point to Settings, and then click Control Panel. 2. Double-click Display and click the Settings tab. 3. Click Advanced. 4. Click the tab for your video card. NOTE: To determine the type of video card installed in your computer, see the Windows Help and Support Center. To access the Help and Support Center, click Start® Help and Support. Under Pick a Task, click Use Tools to view your computer information and diagnose problems.
Back to Contents Page Adding and Replacing Parts Dell™ XPS™ M1730 Owner's Manual Before You Begin Hard Drive Memory Subscriber Identity Module Internal Card With Bluetooth™ Wireless Technology Optical Drive Before You Begin This chapter provides procedures for removing and installing the components in your computer.
NOTICE: Damage due to servicing that is not authorized by Dell is not covered by your warranty. NOTICE: When you disconnect a cable, pull on its connector, not on the cable itself. Some cables have a connector with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep them evenly aligned to avoid bending any connector pins.
1 captive screws (2) 3. 1 Loosen the four captive screws on the hard drive cage and then lift the pull-tab to flip the cage towards the center of the computer so that the SATA cables and connectors are accessible. captive screws (4) 4. Carefully remove the SATA cables from the hard drive or drives that are installed in the cage. Replacing a Hard Drive in the Hard Drive Cage 1.
a. b. Install the hard drive so that the manufacturer's label faces the bottom of the drive cage and the SATA connectors are at the open end of the cage. Install the primary hard drive in the tray labeled 0. You can install a secondary hard drive in the tray labeled 1. Replacing the Hard Drive Cage 1. Place the hard drive cage upside down on the bottom of the computer with the SATA connectors and cables aligned, and then firmly press the cables onto the hard drives' connectors. 2.
1 memory module 2 securing clip NOTICE: If you need to install memory modules in two connectors, install a memory module in the connector labeled "DIMMA" before you install a module in the connector labeled "DIMMB." Insert memory modules at a 45-degree angle to avoid damaging the connector. 5. Ground yourself and install the new memory module: NOTE: If the memory module is not installed properly, the computer may not boot properly. No error message indicates this failure. a. b.
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. NOTE: Only GSM (HSDPA) type cards need a SIM. EVDO cards do not use a SIM. 1. Follow the procedures in Before You Begin. 2. In the battery bay, locate the SIM compartment. 3. Slide in the SIM into the compartment as indicated on the battery bay.
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. 1. Follow the procedures in Before You Begin. 2. Save and close any open files, exit any open programs, and shut down the computer. 3. Remove the optical-drive locking screw. 4. Insert a scribe into the notch and push it to the side to release the drive from the bay. 1 optical drive 3 notch 5. 2 locking screw Slide the drive out of the bay.
Back to Contents Page Securing Your Computer Dell™ XPS™ M1730 Owner's Manual Security Cable Lock Passwords Security Cable Lock NOTE: Your computer does not ship with a security cable lock. A security cable lock is a commercially available antitheft device. To use the lock, attach it to the security cable slot on your Dell™ computer. For more information, see the instructions included with the device.
Back to Contents Page Setting Up Your Computer Dell™ XPS™ M1730 Owner's Manual Connecting to the Internet Transferring Information to a New Computer Setting Up a Printer Power Protection Devices Connecting to the Internet NOTE: ISPs and ISP offerings vary by country. To connect to the Internet, you need a wireless modem/router or network connection and an Internet service provider (ISP).
3. Click Start a new transfer or Continue a transfer in progress. Follow the instructions provided on the screen by the Windows Easy Transfer wizard. Setting Up a Printer NOTICE: Complete the operating system setup before you connect a printer to the computer. See the documentation that came with the printer for setup information, including how to: l Obtain and install updated drivers. l Connect the printer to the computer. l Load paper and install the toner or ink cartridge.
Several devices are available to protect against power fluctuations and failures: l Surge protectors l Line conditioners l Uninterruptible power supplies (UPS) Surge Protectors Surge protectors and power strips equipped with surge protection help prevent damage to your computer from voltage spikes that can occur during electrical storms or after power interruptions. Some surge protector manufacturers include warranty coverage for certain types of damage.
Back to Contents Page Specifications Dell™ XPS™ M1730 Owner's Manual NOTE: Offerings may vary by region. For more information regarding the configuration of your computer, click Start® Help and Support and select the option to view information about your computer.
l l l l Memory Stick PRO xD-Picture Card Hi Speed-SD Hi Density-SD Ports and Connectors Audio microphone-in connector, two stereo headphones/speakers connector IEEE 1394a 4-pin mini, nonpowered connector Consumer IR sensor compatible with Philips RC6 (receive only) Network adapter RJ-45 port S-video TV-out 7-pin mini-DIN connector (optional S-video to composite video adapter cable; optional S-video to component video adapter cable) USB four 4-pin USB 2.
Dimensions: Height 245.0 mm (9.64 inches) Width 383.0 mm (15 inches) Diagonal 431.8 mm (17 inches) Maximum resolution 1920 x 1200 Refresh rate 60 Hz Operating angle 0º (closed) to 142° Viewing angle (typical): Horizontal ±60° Vertical ±45° Pixel pitch 0.191 mm (17-inch display) Power consumption (panel with backlight) (typical): 7.54 W Controls brightness can be controlled through keyboard shortcuts Keyboard Number of keys 101 (U.S.
AC Adapter Input voltage 90–264 VAC Input current (maximum) 3.2 A Input frequency 47–63 Hz Output current 11.8 A (continuous), 12.8A peak 4 second pulse Output power 230 W Rated output voltage 19.5 VDC Dimensions: Height 43 mm (1.7 inches) Width 100 mm (3.93 inches) Depth 200 mm (7.87 inches) Weight (with cables) 1.3 kg (2.86 lb) Temperature range: Operating 0° to 40°C (32° to 104°F) Storage –40° to 65°C (–40° to 158°F) Physical Height 50.8 mm (2.
Back to Contents Page Dell™ XPS™ M1730 Owner's Manual Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your computer. NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death. Information in this document is subject to change without notice. © 2007-2008 Dell Inc. All rights reserved.
Back to Contents Page Traveling With Your Computer Dell™ XPS™ M1730 Owner's Manual Identifying Your Computer Packing the Computer Travel Tips Identifying Your Computer l l Attach a name tag or business card to the computer. Write down your Service Tag and store it in a safe place away from the computer or carrying case. Use the Service Tag if you need to report a loss or theft to law enforcement officials and to Dell. l Create a file on the Microsoft® Windows® desktop called if_found.
Back to Contents Page
Back to Contents Page Troubleshooting Dell™ XPS™ M1730 Owner's Manual Dell Technical Update Service Network Problems Dell Diagnostics Power Problems Dell Support Utility Printer Problems Drive Problems Scanner Problems E-Mail and Internet Problems Sound and Speaker Problems Error Messages Touch Pad or Mouse Problems ExpressCard Problems Video and Display Problems IEEE 1394 Device Problems Drivers Keyboard Problems Lockups and Software Problems Memory Problems Troubleshooting Software and H
The computer runs the Pre-boot System Assessment, a series of initial tests of your system board, keyboard, hard drive, and display. During the assessment, answer any questions that appear. l l If a failure is detected, the computer stops and beeps. To stop the assessment and restart the computer, press ; to continue to the next test, press ; to retest the component that failed, press . If failures are detected during the Pre-boot System Assessment, write down the error code(s) and contact Dell.
Test questions. Custom Test Tests a specific device in the system and can be used to customize the tests you want to run. Symptom Tree Lists a number of common symptoms and allows you to select a test based on the symptom of the problem you are having. For any problem encountered during a test, a message appears with an error code and a description of the problem. Write down the error code and problem description exactly as it appears and follow the instructions on the screen.
Click Start ® Computer. If the drive is not listed, perform a full scan with your antivirus software to check for and remove viruses. Viruses can sometimes prevent Windows from recognizing the drive. Test the drive — l Insert another floppy disk, CD, DVD, or BD to eliminate the possibility that the original media is defective. l Insert a bootable floppy disk and restart the computer. Clean the drive or disk — See Cleaning Your Computer.
l Ensure that the sound is not caused by the program that is running. l Ensure that the disc is inserted properly. Hard drive problems Allow the computer to cool before turning it on — A hot hard drive may prevent the operating system from starting. Try allowing the computer to return to room temperature before turning it on. Run Check Disk — Windows XP 1. Click Start and click My Computer. 2. Right-click Local Disk C:. 3. Click Properties® Tools® Check Now. 4.
Fill out the Diagnostics Checklist as you complete these checks. CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. If the message is not listed, see the documentation for the operating system or the program that was running when the message appeared. Auxiliary device failure — The touch pad or external mouse may be faulty. For an external mouse, check the cable connection.
A memory module may be loose. Reinstall the memory modules and, if necessary, replace them (see Memory). General failure — The operating system is unable to carry out the command. The message is usually followed by specific information—for example, Printer out of paper. Take the appropriate action. Hard-disk drive configuration error — The computer cannot identify the drive type. Shut down the computer, remove the hard drive (see Hard Drive), and boot the computer from a CD.
Memory address line failure at address, read value expecting value — A memory module may be faulty or improperly seated. Reinstall the memory modules and, if necessary, replace them (see Memory). Memory allocation error — The software you are attempting to run is conflicting with the operating system, another program, or a utility. Shut down the computer, wait 30 seconds, and then restart it. Try to run the program again. If the error message still appears, see the software documentation.
3. Click Uninstall. 4. See the program documentation for installation instructions. Windows Vista 1. Click Start ® Control Panel® Programs® Programs and Features. 2. Select the program you want to remove. 3. Click Uninstall. See the program documentation for installation instructions. Sector not found — The operating system cannot locate a sector on the hard drive. You may have a defective sector or corrupted FAT on the hard drive.
ExpressCard Problems CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. Check the ExpressCard — Ensure that the ExpressCard is properly inserted into the connector. Check that the card is recognized by Windows — Double-click the Safely Remove Hardware icon in the Windows taskbar. Some cards do not support this feature. If the card supports this Windows feature, the card will be listed.
External keyboard problems NOTE: When you attach an external keyboard, the integrated keyboard remains fully functional. Check the keyboard cable — Shut down the computer, disconnect the keyboard cable and check it for damage, then firmly reconnect the cable. If you are using a keyboard extension cable, disconnect it and connect the keyboard directly to the computer. Check the external keyboard — 1. Shut down the computer, wait 1 minute, and then turn it on again. 2.
The computer stops responding NOTICE: You might lose data if you are unable to perform an operating system shutdown. Turn the computer off — If you are unable to get a response by pressing a key on your keyboard or moving your mouse, press and hold the power button for at least 8 to 10 seconds until the computer turns off, then restart your computer. A program stops responding or crashes repeatedly End the program — 1. Press simultaneously. 2.
Check the Dell MediaDirect help file for information — Use the Help menu to access Dell MediaDirect Help. To play movies with Dell MediaDirect, you must have a DVD drive and the Dell DVD Player — If you purchased a DVD drive with your computer, this software should already be installed. Video Quality problems — Turn off the Use Hardware Acceleration option.
l See the software documentation for minimum memory requirements. If necessary, install additional memory (see Memory). l Reseat the memory modules to ensure that your computer is successfully communicating with the memory (see Memory). Run the Dell Diagnostics (see Dell Diagnostics). l If you experience other memory problems — l Reseat the memory modules to ensure that your computer is successfully communicating with the memory (see Memory).
Check the power light — When the power light is lit or blinking, the computer has power. If the power light is blinking, the computer is in Sleep state—press the power button to exit Sleep state. If the light is off, press the power button to turn on the computer. NOTE: For information on Sleep power state, see Standby and Sleep Mode. Charge the battery — The battery charge may be depleted. 1. Reinstall the battery. 2. Use the AC adapter to connect the computer to an electrical outlet. 3.
NOTE: If you need technical assistance for your printer, contact the printer's manufacturer. Check the printer documentation — See the printer documentation for setup and troubleshooting information. Ensure that the printer is turned on Check the printer cable connections — l See the printer documentation for cable connection information. l Ensure that the printer cables are securely connected to the printer and the computer.
l Ensure that the scanner cables are securely connected to the scanner and the computer. Verify that the scanner is recognized by Microsoft Windows — Windows XP 1. Click Start® Control Panel® Printers and Other Hardware® Scanners and Cameras. 2. If your scanner is listed, Windows recognizes the scanner. Windows Vista 1. Click Start ® Control Panel® Hardware and Sound® Scanners and Cameras. If the scanner is listed, Windows recognizes the scanner.
Test the electrical outlet — Ensure that the electrical outlet is working by testing it with another device, such as a lamp. Eliminate possible interference — Turn off nearby fans, fluorescent lights, or halogen lamps to check for interference. Reinstall the audio driver — See Reinstalling Drivers and Utilities. Run the Dell Diagnostics — See Dell Diagnostics. NOTE: The volume control in some MP3 players overrides the Windows volume setting.
4. At the Windows desktop, use the touch pad to move the cursor around, select an icon, and open it. If the touch pad operates correctly, the mouse may be defective. Check the system setup program settings — Verify that the system setup program lists the correct device for the pointing device option (the computer automatically recognizes a USB mouse without making any setting adjustments).
Press and the up- or down-arrow key. Eliminate possible interference — Turn off nearby fans, fluorescent lights, halogen lamps, or other appliances. Rotate the computer to face a different direction — Eliminate sunlight glare, which can cause poor picture quality. Adjust the Windows display settings — Windows XP 1. Click Start® Control Panel® Appearance and Themes. 2. Click the area you want to change or click the Display icon. 3. Try different settings for Color quality and Screen resolution.
Many drivers, such as the keyboard driver, come with your Microsoft® Windows® operating system. You may need to install drivers if you: l Upgrade your operating system. l Reinstall your operating system. l Connect or install a new device. Identifying Drivers If you experience a problem with any device, identify whether the driver is the source of your problem and, if necessary, update the driver. Windows XP 1. Click Start® Control Panel. 2.
state that existed before you installed the new driver. Using the Drivers and Utilities Media If using Device Driver Rollback or System Restore (see Restoring Your Operating System) does not resolve the problem, reinstall the driver from your Drivers and Utilities media. 1. With the Windows desktop displayed, insert your Drivers and Utilities media. If this is your first time to use your Drivers and Utilities media, continue to step 2. If not, proceed to step 5. 2.
NOTE: The User Account Control window may appear. If you are an administrator on the computer, click Continue; otherwise, contact your administrator to enter the Device Manager. 3. Double-click the type of device for which you are installing the driver (for example, Audio or Video). 4. Double-click the name of the device for which you are installing the driver. 5. Click the Driver tab® Update Driver® Browse my computer for driver software. 6.
NOTE: The procedures in this document were written for the Windows default view, so they may not apply if you set your Dell computer to the Windows Classic view. 1. Click Start ® Help and Support. 2. Type System Restore in the search field, then press . NOTE: The User Account Control window may appear. If you are an administrator on the computer, click Continue; otherwise, contact your administrator to continue the desired action. 3. Click Next and follow the remaining prompts on the screen.
1. Click Start® Control Panel® Performance and Maintenance® System. 2. Click the System Restore tab and ensure that Turn off System Restore is unchecked. Using Dell™ PC Restore and Dell Factory Image Restore NOTICE: Using Dell PC Restore or Dell Factory Image Restore permanently deletes all data on the hard drive and removes any programs or drivers installed after you received your computer. If possible, back up the data before using these options.
NOTE: If you do not log on as a local administrator, a message appears stating that you must log on as administrator. Click Quit, and then log on as a local administrator. NOTE: If the partition for PC Restore does not exist on your computer hard drive, a message appears stating that the partition was not found. Click Quit; there is no partition to delete. 4. Click OK to remove the PC Restore partition on the hard drive. 5. Click Yes when a confirmation message appears.
Reinstalling Windows XP or Windows Vista The reinstallation process can take 1 to 2 hours to complete. After you reinstall the operating system, you must also reinstall the device drivers, virus protection program, and other software. NOTICE: The Operating System media provides options for reinstalling Windows XP. The options can overwrite files and possibly affect programs that are installed on your hard drive.
Back to Contents Page Setting Up and Using Networks Dell™ XPS™ M1730 Owner's Manual Connecting a Network or Broadband Modem Cable Setting Up a Network Wireless Local Area Network Mobile Broadband (or Wireless Wide Area Network) Dell Wi-Fi Catcher™ Network Locator Setting up a computer network provides connectivity between your computer and the Internet, another computer, or a network.
Windows Vista , and then click Connect To® Set up a connection or network. 1. Click the Windows Vista Start button 2. Select an option under Choose a connection option. 3. Click Next, and then follow the instructions in the wizard. Wireless Local Area Network A wireless local area network (WLAN) is a series of interconnected computers that communicate with each other over the air waves rather than through a network cable connected to each computer.
2. Ensure that you have wired Internet access through your broadband modem before you attempt to set up a wireless Internet connection (see Connecting a Network or Broadband Modem Cable). 3. Install any software required for your wireless router. Your wireless router may have been shipped with installation media. Installation media usually contains installation and troubleshooting information. Install the required software according to the instructions provided by the router manufacturer. 4.
Once you have configured your computer for a wireless network, another pop-up notifies you that your computer is connected to that network. Thereafter, whenever you log on to your computer within the range of the wireless network that you selected, the same pop-up notifies you of the wireless network connection. NOTE: If you select a secure network, you must enter a WEP or WPA key when prompted. Network security settings are unique to your network. Dell cannot provide this information.
NOTE: Even if you are able to make a call from your cellular phone in a specific geographical location, that location may not necessarily be within a cellular-data coverage zone. What You Need to Establish a Mobile Broadband Network Connection NOTE: Depending on your computer, you can use either a Mobile Broadband ExpressCard or Mini Card, but not both, to establish a Mobile Broadband network connection.
Enabling/Disabling the Dell Mobile Broadband Card NOTE: If you are unable to connect to a Mobile Broadband network, ensure that you have all the components for establishing a Mobile Broadband connection (see What You Need to Establish a Mobile Broadband Network Connection), and then verify that your Mobile Broadband card is enabled by verifying the setting of the wireless switch. You can turn your Mobile Broadband card on and off using the wireless switch on your computer.
