Specifications

ManualsBrandsAOpen ManualsComputer equipmentDE5100 Series

DE9300

DE9500

DE9100

INSTALLATION INSTRUCTIONS

RIM

MORTISE CONCEALED VERTICAL ROD

WIRE PIG TAIL

End Cap

DE5300

DE5500

DE5100

SIZE A: (DE9000 Series)

Will fit 48" (1219 mm) door opening without cutting.

Can be cut to fit a 40 1/2" (1029 mm) minimum door opening.

SIZE B: (DE9000 Series)

Will fit 36" (914 mm) door opening without cutting.

Can be cut to fit a 34 1/2" (876 mm) minimum door opening.

End Cap Bracket

Filler (DE9000/DE5000)

REQUIRES DORMA ES-100 or AD100 POWER SUPPLY.

Easily accessible slide in and out electronics.

Meets UL, ANSI/BHMA & CBC requirements.

Note: Refer to Individual Series Installation Instructions for templating and installation of device; @ www.dorma-usa.com

These are additional instructions for installation and operation of the "Delayed Egress" unit.

NOTE: "Always disconnect power prior to making

any connections or service!"

Observe proper static discharge grounding procedures

when installing or servicing the Delayed Egress device.

SIZE AA: (DE5000 Series w/ #443 strike)

Will fit 48" (1219 mm) door opening without cutting.

Can be cut to fit a 38 3/4" (984 mm) minimum door opening.

SIZE BB: (DE5000 Series w/ #443 strike)

Will fit 36" (914 mm) door opening without cutting.

Can be cut to fit a 31 3/4" (806 mm) minimum door opening.

85 Decibel Alarm - Standard

LED Status Indicator - Standard

Nuisance Alarm - Standard

Key Switch Control - Standard

Remote Authorized Egress - Standard

Remote Re-Arm - Standard

Remote Bypass - Standard

Door Position Input - Standard, DIP Switch Setting

Auto Reset or Manual Reset, DIP Switch Setting

Auto - Stanadard (Manual - in CA)

Additional Form "C" Relays For Optional Horn etc.

(Rated 1 amp @ 30 vdc)

Touchbar/Rail

Assembly

(Delayed Egress)

Connecting Plugs

NOTE:

If cutting to length is required

carefully remove filler and

electronics for cutting. Use all

grounding precautions.

Assembly

Mortise Cylinder

(factory supplied)

Pt. No. 90B10SC118

Specifications

DE5000 & DE9000 SERIES

DELAYED EGRESS EXIT DEVICE

IDE - 12 8/09

1135-88 95011817

Summary of content (11 pages)

PAGE 1
INSTALLATION INSTRUCTIONS DE5000 & DE9000 SERIES DELAYED EGRESS EXIT DEVICE Note: Refer to Individual Series Installation Instructions for templating and installation of device; @ www.dorma-usa.com These are additional instructions for installation and operation of the "Delayed Egress" unit.
PAGE 2
Cylinder Specification To Change Cylinder: Carefully remove filler from rail. Unscrew cylinder nut, remove actuator and replace cylinder. Spacer required for cylinders over 1 1/8". Insert cylinder as shown, re-install actuator & secure with cylinder nut. Do not over tighten. Re-install filler in rail and reconnect the small pigtail connectors. Use caution not to pinch or bind wires. Standard 1 1/8" mortise cylinder, randomly keyed supplied by factory.
PAGE 3
Basic wire connection DORMA MODEL ES100 24 VOLT DC POWER SUPPLY Specific project or custom wiring diagrams available on request, consult the DORMA techinical service department. NOTE: Always disconnect power prior to making any connections or service. It is recommended that the 120VAC power be supplied from an Uninterrupted Power Supply (UPS) to ensure proper operation during a power failure. Always observe proper static discharge grounding procedure's when installing or servicing the DE device.
PAGE 4
Key switch operation for device. Delayed Egress Mode: Unit is armed and touch bar will not activate the latchbolt. (LED is solid green, audible alarm is off). Initiated after power up, (DIP switch #2 in OFF position) authorized egress mode or re-arm mode. Nuisance Alarm Mode: Unit is armed and touch bar will not activate the latch bolt. (LED is solid green, audible alarm sounds a short tone) DIP switch selectable for 1 or 3 seconds. (See page 2) Initiated by depressing touch bar.
PAGE 5
Cover, end cap and label After all wire connections are made and device checked for operation, install the chassis cover, end cap and label as shown below. NOTE: Compliance with the California Building Code (CBC) requires different label then supplied. The CBC label is shown below. If required, order through Service Parts, model number CBCLBL. Consult with local code & "authority's having jurisdiction". See CBC Secton 1003.1.10 Paragraph 6. KEEP PUSHING. THIS DOOR WILL OPEN IN 15 SECONDS. ALARM WILL SOUND.
PAGE 6
REMOTE CONTROL & MONITORING INPUT DORMA CC-400-D CONTROL CONSOLE SWITCH MOMENTARY-RESET-MOMENTARY Typical Diagram (EXT.) ALARM (LED ON CONTROL PANEL WILL EMIT SAME COLOR STATUS AS DE9000 DEVICE) UP COMMON DPS NC DOWN RED YELLOW GREEN RETURN (EXT.
PAGE 7
PAGE 8
PAGE 9
PAGE 10
PAGE 11
Latch Guard Installation With #463 Strike LHR LHR 1 5/8" Edge of Stop or Mullion 2 3/8" Edge of Stop or Mullion VERTICAL REF. LINE 9300/F9300 VERTICAL REF. LINE 5300/F5300 For added security a latch guard is supplied with the delayed egress device. Install the latch guard along with the standard #463 strike as shown below. If (2) shims supplied are required to meet correct reference dimension the latch guard is the same thickness as (1) shim.