User Guide

ManualsBrandsAOpen ManualsOtherCD32X

High-speed

CD-ROM Drive

User’s Guide

CLASS 1 LASER PRODUCT

CAUTION: INVISIBLE LASER RADIA-

TION WHEN OPEN. AVOID EXPOSURE

TO BEAM.

ADVARSEL: LASERSTRÅLING VED

ÅBNING SE IKKE IND I STRÅLEN.

APPAREIL A LASER CLASSE 1 PRO-

DUIT LASER

ATTENTION: RADIATION DU FAIS-

CEAU LASER INVISIBLE EN CAS

D’OUVERTURE. EVITTER TOUTE EX-

POSITION AUX RAYONS.

VARO! AVATTAESSA OLET ALTTINA

LASERSÄTEILYLLE

VARNING: LASERSTRÅLNING NÄR

DENNA DEL ÄR ÖPPNAD

ÄLÄ TUIJOTA SÄTEESEEN

STIRRA EJ IN I STRÅLEN

LUOKAN 1 LASERLAITE LASER

KLASSE 1

VORSICHT: UNSICHTBARE LASER-

STRAHLUNG, WENN ABDECKUNG

GEÖFFNET NICHT DEM STRAHLL

AUSSETZEN.

VARNING: LASERSTRÅLNING NÄR

DENNA DEL ÄR ÖPPNAD

STIRRA EJ IN I STRÅLEN

PRODUCTO LÁSER DE LA CLASE 1

ADVERTENCIA: RADIACIÓN LASER

INVISIBLE AL SER ABIERTO. EVITE

EXPONERSE A LOS RAYOS.

ADVARSEL: LASERSTRÅLING NÅR

DEKSEL ÅPNES

STIRR IKKE INN I STRÅLEN

Summary of content (10 pages)

PAGE 1
High-speed CD-ROM Drive User’s Guide CLASS 1 LASER PRODUCT CAUTION: INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO BEAM. ADVARSEL: LASERSTRÅLING VED ÅBNING SE IKKE IND I STRÅLEN. APPAREIL A LASER CLASSE 1 PRODUIT LASER VARO! AVATTAESSA OLET ALTTINA LASERSÄTEILYLLE ATTENTION: RADIATION DU FAISCEAU LASER INVISIBLE EN CAS D’OUVERTURE. EVITTER TOUTE EXPOSITION AUX RAYONS.
PAGE 2
Copyright Copyright  1997 by this company. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company.
PAGE 3
Table of Contents Specifications DRIVE PERFORMANCE Disc Data Capacity: Mode 1 Mode 2 Maximum Playing Time Data Transfer Rate (KB/s) Normal speed 1 MTRP Data Buffer Size Drive Reliability (MTBF) 656 MB 748 MB 74 minutes and 42 seconds Mode 1 150 150 * X Mode 2 171 171 * X 128 KB 50,000 POH (25% duty cycle at room temperature) COMPACT DISC Disc Type (data format) Disc Size CD-Audio, CD-ROM (modes 1 and 2), CD-ROM/XA (mode 2, form 1 and form 2), CD-EXTRA, CD-I, Photo-CD (single and multiple sessions), CD
PAGE 4
Dimensions Weight 149 mm x 42 mm x 196.5 mm (5.9”x1.7”x7.7”) ≤ 1.0 kg (2.2 lbs) ENVIRONMENTAL REQUIREMENTS Temperature: Operating Non-operating Humidity: Operating Non-operating +5ºC ~ +45ºC -20ºC ~ +55ºC 20% ~ 80% RH 20% ~ 80% RH LASER COMPONENT RADIATION DATA Wavelength Emission light output power Pulse times 285 ± 25nm Less than 0.3 mW The time base is using 100s by requirement of IEC -1993 825-1 clause 9.
PAGE 5
Table of Contents 1 Installing the CD-ROM Drive Before you begin, turn off the system power. Follow the steps below to install the CD-ROM drive: 1. Remove the cover from your system. Refer to your system user’s manual. 2. Adjust the Master/Slave jumpers on the back of the CD-ROM drive as necessary. (The factory default of the slave mode normally should not be changed. Please refer to Section 4 for more information) 3. Insert the CD-ROM drive unit into a free 5.25-inch drive bay.
PAGE 6
2 Installing the CD-ROM Drivers The CD-ROM package comes with an installation utility. This utility installs the CD-ROM drivers needed by your CD-ROM drive to interact with your PC. The driver installation diskette includes the following files: • AOATAPI.SYS • INSTALL.EXE • README.TXT • READMEJ.TXT NOTE: The INSTALL.EXE file automatically detects the system language environment. For DOS and Windows 3.1 To install the driver in DOS or Windows 3.1: 1. Insert the installation diskette in your 3.
PAGE 7
Table of Contents Changing the CONFIG.SYS File and Enabling the DMA Function Add the following line to your CONFIG.SYS: DEVICE = \AOATAPI.SYS /D: [/zzzz] [/P:xxx,yy] The is the name of the MSCDEX file that will be used to find the device driver. The maximum length of the string is eight characters. The option [/zzzz] in character form specifies the DMA function, the Ultra-DMA 33 function or Bus Master DMA function. Please refer to the README.
PAGE 8
For OS/2 Warp Under OS/2 Warp, select the non-listed CD-ROM option. This option supports the standard ATAPI CD-ROM drives. After selecting this option, OS/2 will autodetect the CD-ROM drive. 3 Using the CD-ROM Drive In most cases, software applications that utilize CD-ROM drives control the CDROM drive operations directly. However, you can control the drive manually using the front-panel controls. 1. Headphone Jack The 3.
PAGE 9
Table of Contents 4 Emergency-eject Option The Emergency-eject option allows the user to manually open the CD tray during a power malfunction. Follow these steps to manually open the disc tray: 1. Locate the tiny hole at the bottom of the disc tray. Gently poke the hole three times with a sharp needle or a clip. 2. When the disc tray opens, pull out the tray and remove the disc from the CD-ROM drive. If your CD-ROM does not have an emergency-eject hole follow these steps: 1.
PAGE 10
5 Jumper Settings This appendix explains the jumper settings on the drive and lists the pin configurations of each connector on the rear panel. There is one jumper at the rear of the CD-ROM drive. This jumper determines how your CD-ROM drive functions. The figure and table below show the four possible jumper settings and their functions. Jumper Setting Function C Use CSEL M Master S Slave None Slave The drive comes preset with the jumper at the S pin.