ＬＤＣ３００２ＢＫ ＬＤＣ３００２Ｗ Ｔ 3-Drawer Lateral File Cabinet
Introduction Please read the following instruction carefully and use the product properly. Please keep this manual and hand it over when you transfer the product. This summary may not include every detailed information of all variations and considered steps. Please contact us when further information and help needed. Before Starting Recommend no. of people needed for assembly:2 Read each section carefully before starting. It is very important that each step is performed in the correct order.
◆ Start assembling furniture H A F E G E D Q C P O B N D L K M I*2 J*2 a*2 b*4 c*28+2 2 d*1 *1
Components of furniture Please check the board number and the hole on the board A LEFT SIDE PANEL 995x450mm QTY:1PC E ANTI-TIPPING LOCK BAR WITH SMALL RIVETS 774x18mm QTY:2PCS K DRAWER FACE PANLE 851x300mm QTY:3PCS B RIGHT SIDE PANEL 995x450mm QTY:1PC C FRONT UNDERSIDE FRAME 898x80mm QTY:1PC F G LEFT BACK PANLE 995x426mm QTY:1PC RIGHT BACK PANLE 995x426mm QTY:1PC L M DRAWER BODY 825x433mm QTY:3PCS FRONT PANEL 823x248mm QTY:3PCS 3 D FRONT LOCK BAR 917x18mm QTY:2PCS H TOP BOARD 902x452m
O HORIZONTAL FILE FOLDER BAR 837x57mm QTY:3PCS P VERTICAL FILE FOLDER BAR 397x47mm QTY:6PCS Q BOTTOM PANEL 898x356mm QTY:1PC Hardware accessories I LEFT SIDE RAIL 425x50mm QTY:3PCS a REAR INTERLOCKING BLOCK QTY:2PCS d PHILLIPS SCREWDRIVER QTY:1PC J RIGHT SIDE RAIL 425x50mm QTY:3PCS b c FLOOR PROTECTOR QTY:4PCS SCREW M4*8 QTY:28+2 PCS e NAME TAG QTY:3PC 4 KEY QTY:1PC
◆ We recommend you assemble on a soft surface to avoid damage to the unit or surface.
STEP 1 Assemble Anti-tipping lock bar (E ) Please put Anti-tipping lock bar(E ) in the interlocking slots on the side panels and fix them with the Rear interlocking block(a ). Note: The Rear interlocking block needs to pass through the small rivets on the rear interlocking rod and correspond to the screw holes on the left and right sides of the interlocking groove.
STEP 2 Assembly Back Panel Connect Left back panel(F)with Right back panel(G)using two Screws(c).
STEP 3 Assemble Left and Right Side Panels As shown, place the Left panel (A ) and the Right panel (B ) under the Back panel and connect them with six Screws(c ).
STEP 4 Assemble Front Bottom Frame (C ) The side panels are placed horizontally, the Front underside frame(C ) is inserted, and the four corners are fixed with four Floor protector(b ) using eight Screws.
STEP 5 Assembly Bottom Panel (Q ) Assemble the bottom panel. The Bottom panel is inclined into the cabinet, which is fastened in the square holes of the left and right sides and the bottom bracket of the back panel.
STEP 6 Assemble the Top Panel(H ) Note: Install the Top Panel (H ) on the left,right side panel and the back panel as shown in the picture, then connect them with eight Screws(c ).
STEP 7 Connect the Front Lock Bar(D ) with the top panel (H ) and side panels (A&B).Then insert the Front Lock Bar (D ) into the left and right pin as shown.
STEP 8 Install Left Side Rail(I*3 ) and Right Side Rail(J*3 ) 8.1 Put Left Side Rail (I ) on the left side panel(A ). 8.2 Put Right Side Rail(J ) on the right side panel(B ).
STEP 9 Install three Drawers 9.1 Connect Drawer Panel(L )with Drawer Panel(K ). 9.2 Put Front Panel (F ) on the Drawer Panel (K ). 9.3 Connect Rear Panel(N ) with Drawer Panel(L ). Note: when installing L and K, be careful not to bend the two sides of the drawer body (L ) many times in order to breaking.
STEP 10 Separate the Inner Rails(I&J ) 10.1 Pull out the rail core from I1. 10.2 Press the black part to take out the rail core (I2). 10.3 As shown in the picture, the left side rail(I )has been divided into two parts, I1&I2. Note: The steps for separating the right side rail(J )are the same as above.
STEP 11 Install inner drawer rails (I1, J1 ) Put Inner Rail on the Drawer Frame(L ). Attach the left inner drawer runners (I1 ) to the left side of the assembled drawer, and attach the right inner drawer runners (J1 ) to the right side of the assembled drawer.
STEP 12 Finish assembly Silde the Drawer Frame into the Body Frame. STEP 13 Put Hanging file folder bar(O )and (P ) on the Drawer panel(L ).
WEIGHT LIMITS: 60KG/132LBS 60KG/132LBS WARNING Enjoy your furniture! This unit has been designed to support the maximum loads shown. Exceeding these load limits could cause sagging, instability, product collapse, and/or serious injury.
WARNING Please make sure that all panels are attached securely. All nails must be driven into the parts straight and tightened firmly. Failure to do so could cause instability, product collapse, and/or serious injury. To prevent tip over: ◆ Place heaviest items in the second drawer. ◆ Unless specifically designed to accommodate,do not set TVs or other heavy objects on the top of this product. ◆ Never allow children to climb or hang on drawers. ◆Only one drawer can be open at one time.
Instructions Le tte rs ize Le tte rs ize A4 A4 Le ga ls ize Le ga ls ize 20
Option 1 For Letter Size File Folders Letter size 21
Option 2 For A4 Size File Folders A4 22
Option 3 For Legal Size File Folders Lagal size 23
