OPTIMA Service Manual For PW181 Project： PD5084 PD5084-3TC P5002H PT5058 Etc.
THESE DOCUMENTS ARE FOR REPAIR SERVICE INFORMATION ONLY. EVERY REASONABLE EFFORT HAS BEEN MADE TO ENSURE THE ACCURACY OF THIS MANUAL; WE CANNOT GUARANTEE THE ACCURACY OF THIS INFORMATION AFTER THE DATE OF PUBLICATION AND DISCLAIMS RELIABILITY FOR CHANGES, ERRORS OR OMISSIONS.
CONTENTS 1、SPECIFICATION …......................................................................................................…………...….. 1-1 General Specification …................................................….....……........................………....…. 1-2 PDP TV Description.............................................. .............................……………...………….. 1-3 Interface and connection ...................................................................................................….
5、White-Balance Adjustment………………………………………………………………………………… 5-1 Equipments list and prepare………………………………………………………………………… 5-2 Preparation and Adjustment process……………………………………………………………… 5-3 Color temperature specification……………………………………………………………………… 26 26 26 26 6、DDC program and test …………………………………………………………………………………… 6-1 Equipments list and prepare…………………………... ………………...………………………….. 6-2 Program and test process ……………………………………………...………..………………….. 28 28 28 7、Flash Update ………………………………………...……………………………………………………..
1、 SPECIFICATION 1-1 General Specification Item Panel Spec Screen size 50 inch plasma display panel Aspect 16:9 Display pixels 1366 x 768 (WXGA) Effective display size 1106mm x 622mm Number of color 1670 million colors Contrast Ration 3000:1 (in dark room) Peak brightness 1000 cd/㎡ RCA x 1 PAL, NTSC, SECAM Audio: L/R x 1 S-Video1 x 1 PAL, NTSC, SECAM Audio: L/R x 1 RCA x 1 PAL, NTSC, SECAM Audio: L/R x 1 S-Video2 x 1 PAL, NTSC, SECAM Audio: L/R x 1 COMPONENT (YCbCr) Y,Cb,Cr x 1
1-2 PDP TV Description z 50 inch（127cm）Large Screen Flat Panel Plasma Display z Panel Resolution: WXGA（1366 x z MAX Brightness of Panel: 1000 cd/m2 z MAX Contrast Ratio of Panel: 3000:1 z View Angle: Greater than 160° z Dual Video, Dual S-Video, Single Y/Cb/Cr（480i, 576i） z Single Y/Pb/Pr （480P, 576P, 720P, 1080i, 1080P）HDTV Ready z Single Video, Audio（L/R）Output z PC D-SUB 15Pin Signal Receiver z DVI-D Signal（TMDS）Receiver, Support z External 10W×2 Speaker z Intelligent Volume Contr
1-3 Interface and connection Please connect this display to other equipment as picture below. You may have many types of equipment as: DVD, VCD, VCR, Set Top Box, X-Box and so on. 1-3-1 Input connection of Video and Audio signal(DVD/VCD/VCR) We have 2 AV input jacks for VIDEO/AUDIO and S-VIDEO/AUDIO. The R / L is Audio input for every VIDEO and S-VIDEO. We have 2 components signal input jack: YCbCr and YPbPr. The R / L is Audio input for every YCbCr and YPbPr.
1-3-2 Input connection of PC signal ▲ Notice: The PC output can not set out of range The highest Resolution input is 1280 X 1024 / 60Hz Some PC models cannot be connected to the set ● D-SUB 15 Pin: Connect D-SUB signal cable（VGA cable）from PC to D-SUB jack at the back of this display. And connect earphone cable from PC earphone output jack to AUIDO input jack near to the D-SUB jack.
1-3-3 Output connection of Video and Audio signal The VIDEO OUTPUT part is analog Video （CVBS）and Audio output. L & R is Audio left and right channel. They can connect to other analog Video（CVBS） input and Audio input device. See the picture as top.
2-3 RS-232 Pin Description Pin Description 1 No Connection 2 RXD (Receive data) 3 TXD (Transmit data) 4 DTR (DTE side ready) 5 GND 6 DSR (DCE side ready) 7 RTS (Ready to send) 8 CTS (Clear to send) 9 No Connection 2-4 S-VIDEO Pin Description（Y/C separation） Pin Description 1 GROUND 2 GROUND 3 Y 4 C 2-5 Composite Pin Description RCA female 2-6 Components Pin Description（YPbPr/YCbCr） RCA female * 3 2-7 Audio Pin Description RCA female *6 (Red/White：Right/left channel ) Page 9 of
3、Operation 3-1 Operation of Remote Control Transmitter “FREEZE” Press to freeze the picture, press again to return “POWER” The display turn on /turn off key POWER FREEZE MUTE “VOL-/ VOL+ ” Press VOL -/ VOL +key adjust volume “VIDEO” S-Video2、AV2、YCbCr、S-Video1、 AV1 source select key “GRAPHIC ” D-SUB、DVI、Y，Pb，Pr （HDTV）source input SOUND FAVORI TE CH “WIDE” Fill all, Normal, Wide, Zoom display select VOL VIDEO “PIP” Picture in Picture On or Off key TV “ADJ-/ ADJ +/▲/▼” Adjuct the data in Menu
3-2 Front panel controls - CH + - VOL + MENU MODE ④ ⑤ ② ③ ⑥ ① ⑦ ① ② IR: Remote Control aim at this part. （infrared ray Receiver） : Power Key. Press the key into standby or Turn on state. ③ Power Indicator: Power Indicator: Green（Turn On） Power Indicator: Red（Stand by） ④ MODE: Signal Source selection. Press repeatedly to select from the available Signal Input: D-SUB → DVI → YPbPr → S-VIDEO1 YCbCr← AV2 ←S-VIDEO2← AV1 ⑤ MENU: Displays the On Screen Display and setup the display.
3-3 MENU Function MENU Function 1. Press “MENU” key on Remote Control Transmitter or Front panel controls 2. Press “▲/▼”Move the cursor up and down select sub menu item 3. Press “ADJ +” enter sub menu item, and adjuct in the item. 3-3-1 Main MENU Press "MENU" key to enter the main menu, as shown below.
CONTRAST: Contrast adjust 0 ~ 100 Adjust BRIGHTNESS: Brightness adjust 0 ~ 100 Adjust COLOUR: Color chroma adjust 0 ~ 100 Adjust SHARPNESS: Sharpness adjust TINT: Tint adjust only in NTSC system Mode H．PHASE: Horizontal Phase adjust（only in D-SUB Mode） COLOUR TEMP.: Color temperature select，standard→ Warm →Cool Press “▲ /▼”Move the cursor up and down select sub item Press “ADJ+” enter sub menu item, and press “ADJ-/ ADJ+”adjust in the item 3-3-3 Sound MENU Sound adjustment menu, as shown below.
3-3-4 Setup MENU Sound adjustment menu, as shown below.
H．POSITION: Display picture horizontal location adjust V．POSITION: Display picture vertical location adjust H.RES: Horizontal resolution adjustment V.RES: Vertical resolution adjustment (Optima recommend default setting are not changed) (H.RES And V.RES function is available on D-SUB input only, It is normal that display will display black screen during adjustment.
● SPLIT SCREEN: Two windows display mode After enter it, the main picture is D-SUB，sub picture is AV1,sound is from D-SUB. User can press “W ． SELECT”key select which is main picture.And the sound is follow to the main picture. Press “VIDEO” key can select main picture source: S-VIDEO2 , AV1, AV2 etc. Press“SWAP” key can exchange two picture. ▲ ▲ Some source can’t be selected, and some source display need wait for a moment. If user found some abnormal in picture, can turn off power of this TV Set.
4、Trouble shooting chart If replace “IMAGE BOARD”, Please re-do “DDC-content” program & “WHITE-BALANCE” & Flash Update. 4-1 PANEL Trouble shooting Please reference the “PANEL Service Manual”. 4-2 Image board trouble shooting 4-2-1 No display(PANEL) No display (Raster) Image board (Image processing) Check the input power(J40) Check the voltage of STB5V（L49） Voltage=5V（4.2---5.3V） Check the voltage of REL-SW in level ). The testing point:RB22. High level= 5V（4.2---5.
4-2-2 No display(Image board) No display (Raster) Check input voltage is right? NO Repair the PANEL power YES The status of CPU （U20）is right? NO X3 Osc. frequency =14.318MHZ？ YES NO YES 1. Check software ver. 2. Check PIN short? Chcek RESET signal，U21 Pin 6 NO =High level when power on. YES NO Check the supply of Scaler and Osc. frequency YES Measure LVDS input/output signal 号 NO Regarding the status to repair. YES 1.Check scaler (U20) input signal, 2.Check supply of scaler (U20). 1.
4-2-3 Dynamic single mode defective single mode defective (TV,VIDEO,S-Video or YCbCr) Check RGB mode is normal? YES YES Check DVI mode is normal? NO NO Change to PIP mode, and change the sub-picture to VIDEO mode. Check U20(SCALER) DC power Sub-picture is supply,X3 Osc. Frequency, and YES output signal whether normal? normal? If abnormity, please replace relevant parts.
4-2-4 RGB or DVI mode defective Mode mo display U14 1 2 L MST9883 D-SUB，HDTV 0 2 L Check power switch is in “POWER ON” status, and check DC POWER block L45 All voltage is normal? Disconnect the signal cable, is the screen show “Searching” NG Connect the cable again, LED status. Connect signal cable again OK NG LED red or no response LED orange Yes, there are have OSD 1.D-SUB(or HDTV)mode: Measure Y, Pb, Pr (or R, G,B) input signal at U14. 2.Measure VSYNC and HSYNC input signal at U14.
4-2-5 Graphic-Block YPbPr,RGB,DVI Mode no display Check power switch is in NG “Power ON” status, and check Chcek the DC POWER circuit. DC POWER block. OK No, nothing is shown. Disconnect the signal cable. Is the Connect screen show “Searching”? again, check LED status. Yes, there are have OSD show the signal cable LED Red or no response. LED Orange Press power key. If the Connect the signal cable LED color is still red, OK 1.
4-2-6 Video-Block VIDEO、S-VIDEO、Y/Cb/Cr Mode no display U1 Check power switch is in “Power ON” status, and check DC POWER block. Same above OK Disconnect the signal cable. Is the screen show “Searching”? X1 Connect the signal cable 1.AV mode: Measure C4 input waveform at U1. 2.S-VIDEO mode: Measure C4 and C3 input waveform at U1. 3.YCbCr mode: Measure C18/C19/C20 input waveform atU1. NG Check relevant circuit whether have short or open, and check the signal cable whether normal.
4-2-7 直流电源电路 Check the wire from J40/J41 or J43/J44 is tight enough? OK Measure the DC input voltage: L49 L48 L61 L60 L50 L44 L43 --Æ --Æ --Æ --Æ --Æ --Æ --Æ Check relevant circuit whether 5V 5V 6 V (SAMSUNG PANEL) 12 V (SAMSUNG PANEL) 12 V (SAMSUNG PANEL) 3.3 V 9V NG have short . Is there any shortage or cold solder? Measure Pin2 at U23,U24,U25: U23--Æ PIN2 = 1.5V U24--Æ PIN2 = 3.3V U25--Æ PIN2 = 2.5V Measure Pin2 at U5,U10,U11,U41: U5 --Æ PIN2 = 2.5V U10--Æ PIN2 = 3.3V U11--Æ PIN2 = 3.
4-3 Tuner board trouble shooting TA8851 Check DC Power: L530 ＝9V？ L35 ＝5V？ L902 ＝9V？ L34 ＝5V？ L38 ＝5V？ NG Check U45 and relevant circuit. DC converter U905:9V-Æ8V OK In TV mode: Check the system of Video and audio are right? Check U901 and U902 relevant circuit. U901/U902 power supply ＝5V? U901/U902 I2C I/O signal ≈5V? NG Check R902/R908: R902＝GND? R908＝5V? OK Check input/output at U5(TA8851).
4-4 Audio board trouble shooting 4-4-1 DC power circuit +12V Check the wire from P602 is tight enough? OK Measure input DC at P602: Pin1/2＝12V? Pin3/4＝GND Measure input DC at U675(TA2024): U675 testing point＝12V? U675 Pin25/26＝12V? NG Check whether have short or open OK Measure L603,L604,L605,L606=10UH? And check the waveform(sine wave).
5、White-Balance Adjustment 5-1 Equipments list Chroma7100 1set VG828 video signal generator 1set Chroma-2326 1set 5-2 Preparation and Adjustment process 1、Preparation: z Connect correctly the ports that one is HDTV of PDP and the other is VG-828. z Connect correctly the ports that one is D-SUB of PDP and the other is VG-828. z Connect correctly the ports that one is AV of PDP and the other is VG-828.
2). Low brightness adjustment：VG-828 is set TIM20&PAT936（the level of full white is equal to 0.7070） ，measure the temperature of the currently picture by Chroma7100,then compare the measured value and the standard value, if over the specification, then press the button MTS,9,5,1,and display on the Remote control ,and in the factory mode ,adjust the high brightness, so that make the value meet specification.
6、DDC program and test 6-1 Equipments list and prepare DDC tester 1PCS PC 1set D-SUB cable 1PCS DVI cable 1PCS Barcode reader 1set Prepare before test: 1. Turn on the power of your PC and programmer, then make good connection of them. 2. Connect the D-SUB wire and DVI wire to the DDC program equipment and the PDP monitor. 6-2 Program and test process 1. Choose different DDC menu according to different customer , do use PAGE DOWN/PAGE UP to go to the submenu and parent menu until find the right model.
7、Flash Update 7-1 The list of Instrument 1、Prepare 1 piece of RS232 cable（The Pin connection see the Figure-1，If difference, please re-connect the cable）and 1 set of PC. 2、Connect the RS232 cable with PC and PDP(See the Figure-2). PC RS232 Connector RS232 Cable Figure-1 Figure-2 7-2 Flash Update FlashUpgrader is a Windows utility that installs hex files into the FLASH ROM of the target ImageProcessor system. The FlashUpgrader is a Windows-based application.
Step 2: Choose the director of the file to flash Step 3: Flash only the file required Step 4: Connect the computer’s serial port (usually COM1) to the serial port of the Pixelworks evaluation board using a null modem cable, and select speed.
Step 5: Press reset or cycle the power from the Evaluation Board and click “Flash” . Step 6: View hex file flashing progress,after the files have been downloaded, Click “Close” to exit The FlashUpgrader, in conjunction with the code in the flasher.hex file, downloads *.hex files to the Flash ROM on the target board. The FlashUpgrader communicates with the boot code as described in the next section. If communication is established, FlashUpgrader downloads the flasher.hex file.
8、Software Flow Chat 8-1 Main loop Flow Chat Start main loop No Is input 1 marked for calibration? Check input(Input 1) Yes Is view set to single input? No Is input 2 marked for calibration? No Yes Yes Is any input marked for calibration? Yes Set the OSD to be turn off No Yes Is OSD set to be turned NO Turn off the OSD No Is input 1 marked for calibration Yes Calibrate input 1 No Is input 2 marked for calibration Yes Calibrate input 2 No Yes Show the input information Is input informati
Page 33 of 64
8-2 Analog setup flow chat Page 34 of 64
8-3 Power on reset flow chat Power on reset System power up Initialize the key value Oscillator frequency doubling Bland the display Initialize the serial interface Set the panel and display area Power down the panel Initialize timer 0 to timer various events Start main loop Initialize the input selection for each path 9、Block diagram & Explain 9-1 PDP block diagram and functions CN8005 to P15 CN8006 to P15 CN8007 to Power supply （PSU） PANEL J602 to CN8002 CN8004 to J43 CN8003 to J40 CN8001
1) Image board(MGPC): Decode the video signal, De-interlace, and send digital signals (LVDS signal) sent from image Board and display. 2) Audio board(AUPC): Audio signal AMP. and balance process. 3) Tuner board(TUPC): Input signal interface and tuner. 4) Key board(KEPC): POWER, INPUT source, MANUAL, Volume＋/－ and CH＋/－. 5) Power ON/OFF: AC power switch.
S-VIDEO、YcbCr signal: no via Y/C separate，and directly send it to decode circuit, and the following process is same as the Video. YPbPr、RGB signal: via A/D send to SCALER chip for processing the image. DVI signal: via digital process chip transform into digital signal then sent it to SCALER chip to process the image.
10、Waveform of signal 10-1 Waveform of input signal (Instrument outputs the sub board signal，Instrument：VG828/ TG19CC/Oscillograph) YCbCr:Timing946 Pattern946 color bar picture Y Luminance signal R red signal B blue signal YCbCr:Timing 949 Pattern936 full white picture Y signal YCbCr:Timing 949 Pattern921 full white picture Y signal Page 38 of 64
YPbPr:Timing955 Pattern946 color bar picture Y Luminance signal R red signal B blue signal YPbPr:Timing953 Pattern921 gray picture Y signal YPbPr:Timing954 Pattern936 full white picture Y signal Video:Timing946 Pattern946 color bar picture Video:Timing949 Pattern936 full white picture Page 39 of 64
Video:Timing949 Pattern921 gray picture S-video:Timing946 Patern946 color bar picture Y signal S-video:Timing949 Pattern936 full white picture Y signal S-video:Timing949 Pattern921 gray picture Y signal 10-2 Testing point and waveform(MGPC) Video:Timing946 Pattern946 color bar picture U5（Y/C separate）input pin2 C33 U5（Y/C separate）output pin34/32 C534/C535 Page 40 of 64
Video:Timing 949 Pattern936 full white picture Decoder output 8bit digital signal S-Video:Timing 946 Pattern946 color bar picture U5 pin9, pin11 YCbCr:Timing946 Pattern946 color bar picture Y—C18 signal S-Video:Timing 949 Pattern946 color bar picture U16 output 8bit digital signal R—C20 signal B—C19 signal Page 41 of 64
YCbCr:Timing 949、946 Pattern921、936、946 gray, color bar, full white picture Decoder output 8bit digital signal YPbPr:Timing 955 PATTERN946 color bar picture Y—L17 signal R—L19 signal B—L18 signal Page 42 of 64
11、Check and Measure 11-1 Image board 11-1-1 Power Check and Measure ④ ① ② ③ Supply with getting red arrow point three interface J43, J40 and J44 that identification come out for power, image of board with the interface among having picture, it corresponding power make detection method separately among following several picture.： ①.
STB5V 6V GND 3.3V 12V Remark: This interface for SAMSUNG power ③. In the following picture it is successively 1 to 5 pin of J41 from left to right. Among them, The 1pin connects D6V，2pin and 4pin are grounded digitally, 3pin connect D12V voltage, 5pin connect D3.3V voltage. The following picture shows: STB5V GND 5V Remark: This interface for LG power ④. In the following picture it is successively 1 to 5 pin of J41 from left to right.
Voltage 3.3V STB5V Corresponding IC position and pin U14(MST9883)Pin(26,27,39,42,45,46,51,52,59,62); U20(29LV800BT) Pin12 和 Pin37; U52(74LV273A)Pin20; U53(74LV273A)Pin20 U20 (PW181) 5V U16(VPC3230D)Pin(59,67,69,76); U41(LT1117-5)Pin2; 6V U41(LT1117-5)Pin3; 9V L43; U42(LT1117-ADJ)Pin2; L902; U905(LT1117-ADJ)Pin3; L530; U5(TA8851CN)Pin18; L36; P801(FX-80S-1.
12、Mechanical of cabinet front disassembly Appendix: Notice of PDP assembly/disassembly: Please be sure to unplug the power cord before remove the back-cover. ( be sure the power is turn-off). Please do not press or scratch PDP(PANEL, Filter, Bezel and so on)surface with anything hard. Before operate, must wear the antistatic wrist-belt and ring. Prevent IC be damaged by ESD.
13、PCB LAYOUT 13-1 Image board PCB LAYOUT Page 47 of 64
13-2 Audio board PCB LAYOUT Page 48 of 64
13-3 Tuner board PCB LAYOUT 13-4 Key board PCB LAYOUT Page 49 of 64
4.
73 R3 75_NS R10 75_NS C4 75 75 AGND C20 0.22uF R2 75 XTALO VAA VAA C37 60 58 24 I2C ADR:0X88 VAA 0.1uF AGND C33 VOUT1 4.7uF/16V R22 47 R20 2K AGND 470 C34 0.
V25SW AV331 U5 LT1117-2.5 VCC C65 C67 C73 C75 C77 C79 C81 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 10uF_E C85 C86 47uF_E 0.1uF VIN VOUT VDD L7 FB_420_OHM_200MA AV331 V25SW L8 FB_420_OHM_200MA AV251 V25SW L9 FB_420_OHM_200MA AVDD11 V25SW L10 FB_420_OHM_200MA AVDD21 2 C87 C88 0.1uF 100uF_E 1 C63 ADJ 3 C61 V25SW VDD AV251 AVDD11 AVDD21 C62 C64 C66 C68 C69 C70 C71 C72 C74 C76 C78 C80 C82 C84 100uF_E 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.
CC2 1nF AV-IN2 CC10 1nF S-CIN2 71 72 75 4 6 2 1 3 79 62 3.3pF 60 58 24 AGND VBB R92 2K VOUT2 VOUT2 CD3 0.1uF VBB L25 FB AGND CF4 is the bypass cap for Q2 R96 470 GPHS GPVS SDA SCL RST1# GPHS GPVS SDA SCL RST1# AGND AGND 31 32 33 34 37 38 39 40 GGE7 GGE6 GGE5 GGE4 GGE3 GGE2 GGE1 GGE0 41 42 43 44 47 48 49 50 GBE7 GBE6 GBE5 GBE4 GBE3 GBE2 GBE1 GBE0 27 28 56 53 54 55 57 GCLK GCLK VSTBY AGND AGND AGND G-PORT G-PORT RK3 47 VDD RK4 47 RK5 47 CC19 CC20 CC21 CC22 CC23 0.
2 VGA-G 2 1 VGA-B Pr VFF 2 D14 BAV99L CA12 22uF CA5 0.1uF 1 AGND U11 VCC AGND 3 VDD CA8 0.1uF CA2 0.1uF CA4 0.1uF CA7 0.1uF CA10 0.1uF LT1117-3.3 Bypass caps for U14 Bypass cap for U12 VDD VIN VOUT L21 FB 2 1 VGA-R CA1 0.1uF AGND AGND VFF HD-PR R66 75_NS 2 VEE is 3.3V PLL power for U14 VGA-B L19 HfFB AGND VGA-R D13 BAV99L VDD VFF VFF U12A 74LV126 3 2 CA13 15uF C112 0.1uF C113 0.1uF CA3 0.1uF CA6 0.1uF CA9 0.
VDD VDD VII VJJ SCDT SCDT R74 560 85 86 RX2P RX2M RX2P RX2M 80 81 93 94 RXCP RXCM VDD RH2 0 RH3 1K_NS 99 3 2 100 GDFEOE GDFEOE RXCp RXCm R75 0 R76 1K_NS R77 0 R78 1K_NS R79 0 R80 1K_NS R81 1K_NS R82 0 7 4 1 R83 1K 9 RSVD ST PD U15 SiI161 OCKINV STAGE PIXS S_D QO23 QO22 QO21 QO20 QO19 QO18 QO17 QO16 QO15 QO14 QO13 QO12 QO11 QO10 QO9 QO8 QO7 QO6 QO5 QO4 QO3 QO2 QO1 QO0 OCLK HSYNC VSYNC DE CTL3 PDO GND GND GND VDD RX2p RX2m 5 39 68 RXCP RXCM RX1p RX1m AGND
MEM BUS V-PORT A15 A16 A17 B16 A19 B17 A20 B18 GRO7 GRO6 GRO5 GRO4 GRO3 GRO2 GRO1 GRO0 A4 C6 B5 D7 A5 B6 C7 A6 GGO7 GGO6 GGO5 GGO4 GGO3 GGO2 GGO1 GGO0 A12 B13 C12 A13 B14 A14 B15 C13 GBO7 GBO6 GBO5 GBO4 GBO3 GBO2 GBO1 GBO0 D14 C15 C16 E16 B19 C17 E17 C18 D10 C14 A18 C9 VPB7 VPB6 VPB5 VPB4 VPB3 VPB2 VPB1 VPB0 M2 N1 M1 M3 L4 L3 L1 L2 V3.3 CE2 18pF 3.3K RXD TXD CE1 18pF VG7 VG6 VG5 VG4 VG3 VG2 VG1 VG0 A3 C5 PWXI PWXO PWXI PWXO X3 14.318 3.
V3.3 MEMORY BUS MEM BUS FVPP RB1 FWP# RB2 V3.3 RESET# 0 V3.3 28 11 RB13 47_NS RB14 47 V3.3 12 26 13 14 BYTE# A-DQ15 DQ14 DQ13 DQ12 DQ11 DQ10 DQ9 DQ8 DQ7 DQ6 DQ5 DQ4 DQ3 DQ2 DQ1 DQ0 47 45 43 41 39 36 34 32 30 44 42 40 38 35 33 31 29 CE8 0.1uF PWD15 PWD14 PWD13 PWD12 PWD11 PWD10 PWD9 PWD8 PWD7 PWD6 PWD5 PWD4 PWD3 PWD2 PWD1 PWD0 U21 bypass cap V3.3 U21 TLC7733 SW2 7 2 RESIN CE4 0.1uF CE5 47uF 3 SW RST CE7 0.
VDDp PDC-5V VPP JP4 6 4 2 PDC-5V RL11 10K_NS HEADER 3X2 CL7 47uF CL3 0.1uF USE JUMPER U55 4 HEADER SCL SDA SCL SDA CL2 CL4 PDC-ON RST1# 100 100 RL7 RL8 10 9 6 15pF X4 4MHz 7 15pF PDC-ON RST1# 2 3 11 0 RL10 SCL SDA 5 4 3 2 1 P-DATA P-CLK VDDp CON5 15 PDC-ON 4 3 2 1 RESIN PROGRAMER VCC P901 RESIN OSC2 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 P1.7 P1.6 P1.
J34 VDD D-PORT 47 RKQ1 1 9 26 DGE7 DGE6 DGE5 DGE4 DGE3 DGE2 DGE1 DGE0 47 LGB1 LGB0 LGB7 LGB6 RKT1 DBE7 DBE6 DBE5 DBE4 47 LGB5 LGB4 LGB3 LGB2 RKR1 DBE3 DBE2 DBE1 DBE0 4 6 7 11 12 14 8 10 DBE0 DBE1 DBE2 DBE3 DBE4 DBE5 DBE6 DBE7 15 19 20 22 23 24 16 18 DPHS DPVS DPEN 27 28 30 25 DCLK 31 VCC VCC VCC DGE0 DGE1 DGE2 DGE3 DGE4 DGE5 DGE6 DGE7 OUT1 OUT1 OUT2 OUT2 G0 G1 G2 G3 G4 G5 G6 G7 OUT3 OUT3 CLKOUT CLKOUT CLOCK TXE0P TXE0M 45 46 TXE1P TXE1M 41 42 TXE2P TXE2M 37 38 TXE3P TXE3M 39
U40 VCC 8 7 6 RF16 3.3K NS 11 10 LVDSON LVDSON CH13 0.1uF CH14 0.1uF PVCC PVCC RF5 510 TX1P TX1M TX0P TX0M TXCP TXCM 31 30 DVI OUTPUT TX2P TX2M TX2P TX2M 28 27 TX1P TX1M TX1P TX1M 25 24 TX0P TX0M TX0P TX0M 22 21 TXCP TXCM TXCP TXCM U33 J35 U41 D6V 3 2.2K 330_NS DSEL RF11 330_NS CTL1 CTL2 CTL3 BSEL MSEN ISEL RSVD DKEN 5VSC LT1117-5 VIN CH10 0.1uF VDD CH11 0.1uF U33 bypass caps VDD L42 CH30 0.
P602 J603 6 5 4 3 2 1 12VAMP AOUT1+ AOUT1- 2 1 12VAMP AOUT1+ AOUT1- CON2 12VAMP 12VAMP C628 J604 1000pF CON6 AOUT2+ AOUT2- 2 1 AOUT2+ AOUT2- CON2 12VAMP 12VAMP U675 1 2 C601 0.1uF 3 4 L610 C602 1uF R601 FB 5 6 8.2K 7 8 9 R603 L601 DACML FBM2125 R602 + DACML C603 2.2uF/16V C605 100pF 20K 20K 11 12 13 R605 C604 L602 DACMR FBM2125 R604 + DACMR 10 2.2uF/16V C606 100pF VVV 20K 20K 14 15 16 C607 0.1uF 17 18 C621 0.
TP2 R2 TP3 L2 TP7 Y2 TP8 Pb TP9 Pr GROUP_A AUDIO_1 AVIN2 A2-R A2-L GROUP_A YPbPr Y2 Pb Pr AVIN2 A2-R A2-L P901 TP47 P902 1 2 3 4 5 6 7 8 9 R28 75 Z11 5V10PE TP4 AV1 R14 Z16 R13 47K 5V10PE 47K TP5 R1 Z14 5V10PE 1 2 3 4 5 6 7 8 9 TP6 L1 R37 Z30 R38 Z22 R39 75 5V10PE 75 5V10PE 75 AV1-L-R/AV2-L-R Input R29 Z15 R11 75 5V10PE 47K R12 Z12 5V10PE TP10 Y1 TP11 Cb P904 SV2-C SVIN2-C TP48 R30 Y-YUV Cb-YUV Cr-YUV YPbPr/YCbCr Input 5V10PE R34 Z21 R35 75 5V10PE 75
IR_5V P201 13 12 11 10 9 8 7 6 5 SOURCE-SW IR201 2 100 C201 4.
