N27W551T/N32W551T USER'S MANUAL LCD TV L27W551T/L32W551T
TABLE OF CONTENTS IMPORTANT INFORMATION ---------------------------------------------2 Safety-------------------------------------------------------------------------2 LCD panel -------------------------------------------------------------------2 Care---------------------------------------------------------------------------3 OPERATING INSTRUCTION------------------------------------------------6 Remote control -------------------------------------------------------------6 Teletext -------------------------
IMPORTANT INFORMATION Safety Ensure that your domestic mains supply voltage matches the voltage indicated on the identification sticker located at the back of your set. The TV set's components are sensitive to heat.The maximum ambient temperature should not exceed 35° Celsius. Do not cover the vents at the back or sides of the TV set. Leave sufficient space around it to allow adequate ventilation. Install the appliance away from any source of heat (fireplace, ...
Care Use a glass-cleaning product to clean the screen and a soft cloth and mild detergent to clean the rest of the set. Important: Using strong detergents, alcohol-based and abrasive products may damage the screen. Dust the vents at the back and sides regularly. Using solvents, abrasive or alcoholbased products could damage the TV set. Never open the appliance yourself since this may put you at risk or damage the appliance.
SWITCHING ON Follow the instructions on this page on how to switch on your TV set and the remote control before going on to following pages describing how to use the remote control and the channel set-up procedure. 1. Place the TV on a solid surface. 2. Insert the aerial plug firmly into the aerial socket ANT at the back of the TV.
3. Remote control: Remove the cover of the battery compartment. Insert the 2 batteries supplied (Type AAA 1.5V). Please respect the environment and the relevant regulations. Before you dispose of batteries (or accumulators), ask your dealer whether they require special recycling and if he is able to take them back. and if he is able to take them back Precautions on using batteries: - Only use the battery types specified. - Make sure you use the correct polarity. - Do not mix new and used batteries.
OPERATING INSTRUCTION Remote Control Press this key to display : - the channel number when watching a TV program. - the input source when watching an AV program. Press this key to turn on or on stand-by the TV set. PR Press PR+ or PR– to scroll through the channels. Press this key to mute the sound. Press this key again to restore it. Press + or – to increase or decrease the volume. 0~9 DIGIT BUTTONS To select a TV channel. Press this key to adjust the automatic shut-off time (from 0 to 120 minutes).
TELETEXT The Teletext service is available in many countries under a variety of names (TOP Text, Fastext, FLOF text,Videotext). It is provided as a free service by television broadcasters.This service provides a real wealth of information, available at any time, on weather, sports results, news, games, etc.
MENUS MAIN MENU Press the MENU button to display the Main menu. It offers the following options : Picture adjustments, Audio adjustments, PIP/POP adjustments, TV channels search menu (only in TV mode) and PC adjustments (only in PC mode). It also allows to define your preferences in the Setup menu. PICTURE ADJUSTMENTS Display the Main menu by pressing MENU button. Select the Picture menu using the Ÿ / ⁄ buttons. Press the OK button to confirm. Use the Ÿ / ⁄ buttons to select each option.
AUDIO ADJUSTMENTS Display the Main menu by pressing MENU button. Select the Sound menu using the ⁄button. Press the OK button to confirm. Use the Ÿ / ⁄ buttons to select each option. Volume : adjust as required using the ! / ÿ buttons. Balance : adjust the balance between left/right channels as required using the ! / ÿ buttons. Bass : adjust the bass level as required using the ! / ÿ buttons. Treble: adjust the treble level as required using the ! / ÿ buttons.
PIP/PAP ADJUSTMENTS Press the MENU button to display the Main menu Select the PIP menu using the ⁄button. Press the OK button to confirm. Use the Ÿ / ⁄ buttons to select each option. Dual mode: Using ! / ÿ buttons activate (PIP/PAP) or deactivate (Off) the PIP function. Following options are available if you have selected PIP or PAP at the PIP line. Position : use the ! / ÿ buttons to change the position of the PIP frame on the screen.
CHANNELS SEARCH Channels search involves selecting all the settings required to be able to search for and store all the channels you can receive. Make sure that the television is switched on and follow all the steps in turn specified on this page. Display the Main menu by pressing MENU button. Select the Installation menu using the ⁄button. Press the OK button to confirm. Use the Ÿ / ⁄ buttons to select each option. Automatic set-up Select Auto. installation using the ⁄ button.
Name : Allows to edit the channel name. - Using the ⁄ button, select the Name option. - Using the ÿ button select the first letter field. - By pressing the 0~9 digit repeatedly and using the following table select the first character. Repeat the procedure for each letter field. Press the OK button to confirm. BUTTON 1 2 3 4 5 6 7 8 9 0 AVAILABLE CHARACTERS 1 2 3 4 5 6 7 8 9 0 Space A D G J M P S W * — B E H K N Q T X # • ! C F I L O R U Y ( @ # $ % ^ & V Z ) Store prog.
Fine tuning : If the picture is not clear, you can adjust the setting. - Using the ⁄ button, select the Fine Tuning option. - Use the ! / ÿ buttons to find the good tuning point. Man. search : Allows to launch a manual search. - Using the ⁄ button, select the Man. search option. - Using the ! / ÿ buttons, start the search in decreasing or increasing order. The menu is replaced by a sub-menu showing the progression of the search. - The search will stop at the first channel found, Man.
SETUP This menu allows to select the language for the menus as well as the colour of the screen when there is no video input. It allows also to set an automatic shut-off time. Display the Main menu by pressing MENU button. Select the Options menu using the ⁄button. Press the OK button to confirm Use the Ÿ / ⁄ buttons to select each option. Menu language : To select the language for the menus. Menu timeout : To set an automatic shut-off time for Menu.
PC MODE In PC mode, main menu is dfferent from the one in TV mode. Please select PC as main input. PC SETTINGS Display the Main menu by pressing MENU button. Select the PC menu using the ⁄button. Press the OK button to confirm. Use the Ÿ / ⁄ buttons to select each option. H. position : use the ! / ÿ buttons to move the picture horizontally on the screen. V. position : use the ! / ÿ buttons to move the picture vertically on the screen. Focus : Adjust as required to improve the picture quality.
CONTROLS Controls are located on the top of the TV set. button: Press this button to switch on or on standby the TV set. MENU button: Press this button to display the main menu. Ÿ / ⁄ buttons: Press these buttons to select a channel or to choose an option in a menu. – / + buttons: Press these buttons to ajust the volume, access a sub-menu or perform an adjustment in a menu. Source button: To select desire input source, press the SOURCE button to display the selection menu.
AV sockets (Located at the back of the TV set, on the leftside) AV2 SCART socket To connect a VCR, a camcorder, a DVD player or a satellite receiver. AV2 SCART socket is an input socket. AV1 SCART socket To connect a VCR, a camcorder, a DVD player, a satellite receiver, a decoder or a games console. AV1 SCART socket is an input/output socket. Audio socket (Audio output) To connect to an audio amplifier.
HEADPHONE SOCKET (LOCATED AT THE BACK OF THE TV SET, ON THE RIGHTSIDE) When headphones are connected, the sound of TV set is cut. Adjust headphones volume level by using + / - buttons on the remote control. To switch off the sound of the headphone press the button on the remote control. HDMI SOCKET (High-Definition Multimedia Interface) (LOCATED AT THE BACK OF THE TV SET, NEAR THE POWER INPUT SOCKET) This socket allows the connection to all appliances fitted with an HDMI socket.
PC IN SOCKET (LOCATED AT THE BACK OF THE TV SET, NEAR THE HDMI SOCKET) Allows to connect a PC to the TV set Connect the PC IN D-sub socket located at the back of the TV set to the output of PC equipment through a mini D-sub 15 pin cable (2). Connect the stereo PC IN audio jack located at the back of the TV set (near the D-sub socket) to the audio output socket on the computer through an audio cable.
BEFORE CALLING SERVICE Please make these simple checks before calling service. Symptoms “ Ghost ” or double image No power No picture Good picture but no sound Good sound but poor color Poor picture Snowy picture and noise Horizontal dotted line Television not responding to remote control Items to Check and Actions to follow * Make sure the antenna is facing the right direction.. * This may be caused by obstruction to the antenna due to high rise buildings or hills.
