TABLE OF CONTENTS FOR YOUR SAFETY --------------------------------------------------1 SAFETY PRECAUTIONS --------------------------------------2 SPECIAL NOTES ON LCD MONITORS -------------------3 BEFORE YOU OPERATE THE MONITOR ---------------------3 FEATURES --------------------------------------------------------3 PACKING LIST ---------------------------------------------------3 INSTALLATION INSTRUCTIONS ---------------------------4 CONTROLS AND CONNECTORS --------------------------5 ADJUSTING THE VIEWING
Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PRECAUTIONS Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions.
SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. NOTES Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. You may find slightly uneven brightness on the screen depending on the desktop pattern you use. The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.
INSTALLATION INSTRUCTIONS SWIVEL BASE Install Figure 1 Remove Installing and Removing the Swivel Base POWER CORD Power Source: 1. Make sure that the power cord is the correct type required in your area. 2. This LCD monitor has an External universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required.) 3. Connect the power cord into your LCD monitor’s power input socket, and then plug the other end into a 3-pin AC power outlet.
CONTROLS AND CONNECTORS VIDEO CABLE Connecting the D-Sub Cable: Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer’s DSub port. Connecting the Power Cord: Connect the power cord into your LCD monitor’s power input socket, and then plug the other end into a 3-pin AC power outlet. The power cord may be connected to either a wall power outlet or the power outlet socket on your PC, depending on the type of power cord supplied with your LCD monitor.
ADJUSTING THE VIEWING ANGLE For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference. Hold the stand so you do not topple the monitor when you change the monitor’s angle. You are able to adjust the monitor’s angle from -5 to 18. Figure 3 NOTES Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.
OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located on the front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. The power cord should be connected. Connect the video cable from the monitor to the video card. Press the power button to turn on the monitor position. The power indicator will light up.
FRONT PANEL CONTROL Power Button: Press this button to turn the monitor ON or OFF. Power Indicator: Blue — Orange — Power On mode. Off mode. MENU / ENTER : Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON or Exit OSD menu when in Volume Adjust OSD status. Brightness : Adjust brightness or function adjust. Contrast : Adjust contrast or function adjust. Auto Adjust button / Exit: 1. 2.
HOW TO ADJUST A SETTING 1. 2. 3. 4. Press the MENU-button to activate the OSD window. Press or to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate it. If the function selected has a sub-menu, press or again to navigate through the sub-menu functions. Once the desired function is highlighted, press MENU-button to activate it. or to change the settings of the selected function. Press To exit and save, select the exit function.
ADJUSTING THE PICTURE The descriptions for function control LEDS Main Main Sub Menu Menu Menu Item Icon Item Luminance Contrast Image Setup Image Position Color Temp. Sub Menu Icon Description Contrast from Digital-register. Brightness Backlight Adjustment Focus Adjust Picture Phase to reduce Horizontal-Line noise Clock Adjust picture Clock to reduce Vertical-Line noise. H. Position Adjust the horizontal position of the picture. V. Position Adjust the verticalposition of the picture.
Main Menu Item Auto Config OSD Setup Main Menu Icon Sub Menu Item Sub Menu Icon Description Yes N/A Auto Adjust the H/V Position, Focus and Clock of picture. No N/A Do not execute Auto Config, return to main menu. H. Position Adjust the horizontal position of the OSD. V. Position Adjust the verticalposition of the OSD. OSD Timeout Adjust the OSD timeout.
PLUG AND PLAY Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The DDC2B is a bidirectional data channel based on the I²C protocol. The host can request EDID information over the DDC2B channel.
TECHNICAL SUPPORT (FAQ) Problem & Question Power LED is not on No Plug & Play Picture is fuzzy Picture bounces or a wave pattern is present in the picture The power LED is ON (orange) but there’s no video or no picture. Missing one of the primary colors (RED, GREEN, or BLUE) Screen image is not centered or sized properly.
ERROR MESSAGE & POSSIBLE SOLUTION CABLE NOT CONNECTED : 1. Check that the signal-cable is properly connected , If the connector is loose, tighten the connector’s screws. 2. Check the signal-cable’s connection pins for damage. INPUT NOT SUPPORTED : Your computer has been set to unsuitable display mode ,set the computer to display mode given in the following table (See page 17).
APPENDIX SPECIFICATIONS Driving system TFT Color LCD LCD Panel Input Size 38.1cm(15") Pixel pitch 0.297mm( H ) × 0.297mm( V ) Video R,G,B Analog Interface Separate Sync. H/V TTL H-Frequency 30kHz – 60kHz V-Frequency 55-75Hz Display Colors 16.2M Colors Dot Clock 80MHz Max. Resolution 1024 × 768 @75Hz Plug & Play VESA DDC2BTM EPA ENERGY STAR® ON Mode <30W OFF Mode ≤1W Input Connector 15-pin D-Sub Input Video Signal Analog:0.
Switch External Controls: Auto Adjust Key Brightness Contrast Power Button MENU Contrast Brightness Focus Clock H. Position V.
Preset Display Modes STANDARD RESOLUTION HORIZONTAL FREQUENCY VERTICAL FREQUENCY Dos-mode 720 x 400 31.47kHz 70.0Hz VGA SVGA XGA SXGA 640 × 480 31.47kHz 60.0Hz 640 × 480 37.50kHz 75.0Hz 800 × 600 37.879kHz 60.0Hz 800 × 600 46.875kHz 75.0Hz 1024 × 768 48.363kHz 60.0Hz 1024 × 768 56.476kHz 70.0Hz 1024 × 768 60.021kHz 75.0Hz 1280 × 1024 64.000kHz 60.0Hz 1280 × 1024 80.000kHz 75.
CONNECTOR PIN ASSIGNMENT 1 5 6 10 11 15 15 - Pin Color Display Signal Cable PIN NO. 1. 2. 3. 4. 5. 6. 7. 8. DESCRIPTION PI N NO. DESCRIPTION 9. 10. 11. 12. 13. 14. 15.
