I2473PWY /I2473PWM LED Backlight
Safety........................................................................................................................................................................ 4 National Conventions ......................................................................................................................................... 4 Power ................................................................................................................................................................
Regulation ............................................................................................................................................................... 56 FCC Notice ...................................................................................................................................................... 56 WEEE Declaration ...........................................................................................................................................
Safety National Conventions The following subsections describe notational conventions used in this document. Notes, Cautions, and Warnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are used as follows: NOTE: A NOTE indicates important information that helps you make better use of your computer system.
Power The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety feature.
Installation Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with this product. Follow the manufacturer’s instructions when installing the product and use mounting accessories recommended by the manufacturer. A product and cart combination should be moved with care.
Cleaning Clean the cabinet regularly with cloth. You can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauterize the product cabinet. When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface. Please disconnect the power cord before cleaning the product.
Other If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and contact a Service Center. Make sure that the ventilating openings are not blocked by a table or curtain. Do not engage the LCD monitor in severe vibration or high impact conditions during operation. Do not knock or drop the monitor during operation or transportation.
Setup Contents in Box * * * Not all signal cables (Audio,HDMI,MHL ) will be provided for all countries and regions. Please check with the local dealer or AOC branch office for confirmation.
Adjusting Viewing Angle For optimal viewing, it is recommended to look at the full face of the monitor, and then adjust the monitor's angle to your own preference. Hold the stand so you will not topple the monitor when you change the monitor's angle. You are able to adjust the monitor's angle as below. 3 20 NOTE: Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.
Connecting the Monitor Cable Connections In Back of Monitor and Computer: I2473PWM 1. DC port 2. Analog (DB-15 VGA cable) 3. Audio 4. HDMI/MHL 5. Earphone I2473PWY To protect equipment, always turn off the PC and LCD monitor before connecting. 1. Connect the power cable to the DC port on the back of the monitor. 2. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer's D-Sub port. 3.
Speaker Mode: Turn “Speaker mode” on, you can play music via line-in without video signal (D-SUB/HDMI/MHL) input. When “Speaker mode” is on, the indicating led will always show “Blue color” Operation: Main menu Æ OSD Setup Æ Speaker Mode Æ On Miracast Operation: 1. Power on I2473PWY, and select OSD MenuÆ”Extra”Æ”Input select”Æ”Miracast”; or turn on “Miracast” from hot key “Auto” 2.
Brand Model Name HTC New One Butterfly Xperia Z Sony Xperia ZL Samsung Galaxy S IV Galaxy S III Galaxy Note II Xperia V Galaxy Note 8.0 Galaxy Tab 10.1 Google Inc. Nexus 4 LG Electronics Optimus G ZTE 967S Android OS needs to update to the latest version.
Adjusting Setting Optimal Resolution Windows 8 For Windows 8: 1. Right click and click All apps at the bottom-right of the screen. 2. Set the “View by” to “Category”. 3. Click Appearance and Personalization.
4. Click DISPLAY. 5.
Windows Vista For Windows Vista: 1 Click START. 2 Click CONTROL PANEL. 3 Click Appearance and Personalization.
5 Click Display Settings.
Window ws XP For Wind dows XP: 1 Click ST TART. 2 Click SE ETTINGS. ONTROL PAN NEL. 3 Click CO 4 Click Ap ppearance an nd Themes. 5 Double click DISPLAY AY.
6 Click SE ETTINGS. 7 Set the resolution SL LIDE-BAR to Optimal O presett resolution Window ws ME/200 00 For Wind dows ME/2000 0: 1 Click ST TART. 2 Click SE ETTINGS. 3 Click CO ONTROL PAN NEL. 4 Double click DISPLAY AY. 5 Click SE ETTINGS.
Hotkeys 5 2 3 1 4 I2473PWY / I2473PWM 1 Source/ Auto/ Exit 2 Clear Vision /< 3 Volume / > 4 Menu/Enter 5 Power Power Press the Power button to turn on/off the monitor. Volume / > When there is no OSD, press Volume adjust volume. Auto / Exit When there is no OSD, press Auto / Exit button continuously about 3 second to do auto configure. Source hot key When the OSD is closed, press Source button will be Source hot key function.
Clear Vision 1. When there is no OSD, Press the “<” button to activate Clear Vision. 2. Use the “<” or “>” buttons to select between weak, medium, strong, or off settings. Default setting is always “off”. 3. Press and hold “<” button for 5 seconds to activate the Clear Vision Demo, and a message of “Clear Vision Demo: on” will be display on the screen for a duration of 5 seconds. Press Menu or Exit button, the message will disappear.
Using “MHL(Mobile High-Definition Link)” 1. “MHL” (Mobile High-Definition Link) This feature allows you to enjoy videos and photos(imported from a connected mobile device that supports MHL) on the screen of the product. ● To use the MHL function, you need an MHL-certified mobile device. You can check if your mobile device is MHL certified on the device manufacturer’s website. To find a list of MHL-certified devices, visit the official MHL website(http://www.mhlconsortium.org).
OSD Setting Basic and simple instruction on the control keys. 1. Press the MENU-button to activate the OSD window. 2. Press < or > to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate. Press < or > to navigate through the sub-menu. Once the desired function is highlighted, press MENU-button to activate. 3. Press < or > to change the settings of the selected function. Press AUTO to exit.
Luminance 1 Press (Menu) to display menu. 2 Press < or > to select (Luminance), and press 3 Press < or > to select submenu, and press to enter. to enter. 4 Press < or > to adjust. 5 Press to exit. Brightness 0-100 Backlight Adjustment. Contrast 0-100 Contrast from Digital-register. Standard Standard Mode. Text Text Mode. Internet Internet Mode. Game Game Mode. Movie Movie Mode. Sports Sports Mode. Gamma1 Adjust to Gamma 1. Gamma2 Adjust to Gamma 2. Gamma3 Adjust to Gamma 3.
Image Setup 1 Press (Menu) to display menu. 2 Press < or > to select (Image Setup), and press 3 Press < or > to select submenu, and press to enter. to enter. 4 Press < or > to adjust. 5 Press to exit. Clock 0-100 Adjust picture Clock to reduce Vertical-Line noise. Phase 0-100 Adjust Picture Phase to reduce Horizontal-Line noise. Sharpness 0-100 Adjust picture sharpness. H.Position 0-100 Adjust the horizontal position of the picture. V.
Color Setup 1 Press (Menu) to display menu. 2 Press < or > to select (Color Setup), and press 3 Press < or > to select submenu, and press to enter. to enter. 4 Press < or > to adjust. 5 Press to exit. Color setup. Warm Recall Warm Color Temperature from EEPROM. Normal Recall Normal Color Temperature from EEPROM. Cool Recall Cool Color Temperature from EEPROM. sRGB Recall SRGB Color Temperature from EEPROM. Red Red Gain from Digital-register. Green Green Gain Digital-register.
Picture Boost 1 Press (Menu) to display menu. 2 Press < or > to select (Picture Boost), and press 3 Press < or > to select submenu, and press to enter. to enter. 4 Press < or > to adjust. 5 Press to exit. Frame Size 14-100 Adjust Frame Size. Brightness 0-100 Adjust Frame Brightness. Contrast 0-100 Adjust Frame Contrast. H. position 0-100 Adjust Frame horizontal position. V. position 0-100 Adjust Frame vertical position. Bright Frame on or off Disable or Enable Bright Frame.
OSD Setup 1 Press (Menu) to display menu. 2 Press < or > to select (OSD Setup), and press 3 Press < or > to select submenu, and press to enter. to enter. 4 Press < or > to adjust. 5 Press to exit. H. Position 0-100 Adjust the horizontal position of OSD. V. Position 0-100 Adjust the vertical position of OSD. Timeout 5-120 Adjust the OSD Timeout. Transparence 0-100 Adjust the transparence of OSD. Language Select the OSD language.
Extra 1 Press (Menu) to display menu. 2 Press < or > to select (Extra), and press 3 Press < or > to select submenu, and press to enter. to enter. 4 Press < or > to adjust. 5 Press to exit. Input Select Auto / D-SUB / Miracast/ HDMI/MHL Select input signal source. (I2473PWY) Select input signal source. Auto Config Auto / D-SUB/ HDMI1/MHL1/ HDMI2/MHL2 yes or no Off timer 0-24hrs Select DC off time. Image Ratio wide or 4:3 Select wide or 4:3 format for display.
Exit 1 Press (Menu) to display menu. 2 Press < or > to select (Exit), and press to enter. Exit Exit the main OSD.
Driver Monitor Driver Windows 8 1. Start Windows® 8 2. Right click and click All apps at the bottom-right of the screen. 3. Click on the “Control panel” icon 4. Set the “View by” to “Large icons” or “Small icons”.
5. Click on the “Display” icon. 6. Click on the “Change display settings” button. 7. Click the “Advanced Settings” button. 8. Click the “Monitor” tab and then click the “Properties” button.
9. Click the “Driver” tab. 10. Open the “Update Driver Software-Generic PnP Monitor” window by clicking on “Update Driver... “ and then click the "Browse my computer for driver software" button. 11. Select "Let me pick from a list of device drivers on my computer".
12. Click the “Have Disk” button. Click on the “Browse” button and navigate to the following directory: X:\Driver\module name (where X is the drive letter designator for the CD-ROM drive). 13. Select the "xxx.inf" file and click the “Open” button. Click the “OK” button. 14. Select your monitor model and click the “Next” button. The files will be copied from the CD to your hard disk drive. 15. Close all open windows and remove the CD. 16. Restart the system.
Windows 7 1. Start Windows® 7 2. Click on the 'Start' button and then click on 'Control Panel'. 3. Click on the 'Display' icon.
4. Click on the “Change display settings” button. 5. Click the “Advanced Settings” button. 6. Click the “Monitor” tab and then click the “Properties” button.
7. Click the “Driver” tab. 8. Open the "Update Driver Software-Generic PnP Monitor" window by clicking on “Update Driver... “ and then click the "Browse my computer for driver software" button. 9. Select "Let me pick from a list of device drivers on my computer".
10. Click the “Have Disk” button. Click on the “Browse” button and navigate to the following directory: X:\Driver\module name (where X is the drive letter designator for the CD-ROM drive). 11. Select the "xxx.inf" file and click the “Open” button. Click the “OK” button. 12. Select your monitor model and click the “Next” button. The files will be copied from the CD to your hard disk drive. 13. Close all open windows and remove the CD. 14. Restart the system.
Windows Vista 1. Click "Start" and "Control Panel". Then, double-click on "Appearance and Personalization". 2. Click "Personalization" and then "Display Settings". 3. Click "Advanced Settings...".
4. Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the configuration for your monitor is completed. The monitor can be used as is. If the message "Windows needs..." is displayed, as shown in the figure below, click "Continue". 5. Click "Update Driver..." in the "Driver" tab. 6. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer". 7. Click on the 'Have disk...
Window ws XP 1. Start Windows® XP 2. ontrol Panel'. Click on the 'Start' button and then click on 'Co 3. n the categoryy ‘Appearance and Themes’ Selecct and click on 4. ay' Item.
5. Selecct the 'Settingss' tab then clicck on the 'Advanced' button. 6. b Selecct 'Monitor' tab - If the 'Properrties' button is inactive, it me eans your mon nitor is properlly configured. Please stop in nstallation. - If the 'Properrties' button iss active, click on o 'Properties'' button. ase follow the e steps below. Plea 7. n click on 'Upd date Driver...' button.
8. Selecct the 'Install from a list or specific location [advanced]' radio button and a then click on the 'Next' button. 9. hoose the drivver to install' ra adio button. Th hen click on th he 'Next' butto on. Selecct the 'Don't Search. I will ch 10. Click on the 'Have disk...' button, then click on n the 'Browse...' button and then select the appropriate drive F: (CD-ROM Drive). 11. Click on the 'Open' button, then click the 'OK' button. 12.
Windows 2000 1. Start Windows® 2000 2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'. 3. Double click on the 'Display' Icon. 4. Select the 'Settings' tab then click on 'Advanced...'. 5. Select 'Monitor' - If the 'Properties' button is inactive, it means your monitor is properly configured. Please stop installation. - If the 'Properties' button is active. Click on 'Properties' button. Please follow the steps given below. 6.
i-Men nu Welcome to “i-Menu” so oftware by AO OC. i-Menu ma akes it easy to o adjust your monitor m displayy setting by us sing on enus instead of o the OSD bu utton on the monitor. m To com mplete installattion, please fo ollow the installation screen me guide.
e-Saver Welcome to use AOC e-Saver monitor power management software! The AOC e-Saver features Smart Shutdown functions for your monitors, allows your monitor to timely shutdown when PC unit is at any status (On, Off, Sleep or Screen Saver); the actual shutdown time depends on your preferences (see example below). Please click on "driver/e-Saver/setup.exe" to start installing the e-Saver software, follow the install wizard to complete software installation.
Screen+ Welcome to "Screen+" software by AOC. Screen+ software is a desktop screen splitting tool; it splits the desktop into different panels, and each panel displays a different window. You only need to drag the window to a corresponding pane, when you want to access it. It supports multiple monitor display to make your task easier. Please follow the installation software to install it.
Troubleshoot Problem & Question Power LED Is Not ON Possible Solutions Make sure the power button is ON and the Power Cord is properly connected to a grounded power outlet and to the monitor. Is the power cord connected properly? Check the power cord connection and power supply. Is the cable connected correctly? (Connected using the D-sub cable) Check the DB-15 cable connection. (Connected using the DVI cable) Check the DVI cable connection. * DVI input is not available on every model.
Picture Bounces, Flickers Or Wave Pattern Appears In The Picture Move electrical devices that may cause electrical interference as far away from the monitor as possible. Use the maximum refresh rate your monitor is capable of at the resolution you are using. The Computer Power Switch should be in the ON position. The Computer Video Card should be snugly fitted in its slot. Monitor Is Stuck In Active Off-Mode" Make sure the monitor's video cable is properly connected to the computer.
Specification General Specification Panel Resolution Model name I2473PWY Driving system TFT Color LCD Viewable Image Size 604.70mm diagonal Pixel pitch 0.2745 mm x 0.2745 mm Video R, G, B Analog lnterface &HDMI(MHL) lnterface Separate Sync. H/V TTL Display Color 16.7M Colors Dot Clock 170MHz Horizontal scan range 30kHz to 83kHz Horizontal scan Size(Maximum) 527.04 mm Vertical scan range 50Hz to 76 Hz Vertical scan Size(Maximum) 296.
General Specification Panel Resolution Model name I2473PWM Driving system TFT Color LCD Viewable Image Size 604.70mm diagonal Pixel pitch 0.2745 mm x 0.2745 mm Video R, G, B Analog lnterface &HDMI(MHL) lnterface Separate Sync. H/V TTL Display Color 16.7M Colors Dot Clock 170MHz Horizontal scan range 30kHz to 83kHz Horizontal scan Size(Maximum) 527.04 mm Vertical scan range 50Hz to 76 Hz Vertical scan Size(Maximum) 296.
Preset Display Modes HORIZONTAL VERTICAL FREQUENCY(kHZ) FREQUENCY(Hz) 640×480@60Hz 31.469 59.940 VGA 640×480@72Hz 37.861 72.809 VGA 640×480@75Hz 37.500 75.000 SVGA 800×600@56Hz 35.156 56.250 SVGA 800×600@60Hz 37.879 60.317 SVGA 800×600@72Hz 48.077 72.188 SVGA 800×600@75Hz 46.875 75.000 XGA 1024×768@60Hz 48.363 60.004 XGA 1024×768@75Hz 60.023 75.029 SXGA 1280×1024@60Hz 63.981 60.020 SXGA 1280×1024@75Hz 79.976 75.025 WXGA 1440×900@60Hz 55.935 59.
Pin Assignments 1 15-Pin Side of the Signal Cable Video-Red 9 15-Pin Side of the Signal Cable +5V 2 Video-Green 10 Ground 3 Video-Blue 11 N.C. 4 N.C.
Pin No. 1 Signal Na ame TMDS Data a 2+ Pin No. 9 Signal Name e T TMDS Data 0 Pin No. 17 Signal Name e DDC/CEC Gro ound 2 TMDS Data a 2 Shield 10 T TMDS Clock + 18 +5V Power 3 TMDS Data a2 11 T TMDS Clock Shield S 19 Hot Plug Dete ect 4 TMDS Data a 1+ 12 T TMDS Clock 5 TMDS Data a 1Shield 13 C CEC 6 TMDS Data a1 14 R Reserved (N.C C.
Plug and Play Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The DDC2B is a bi-directional data channel based on the I2C protocol. The host can request EDID information over the DDC2B channel.
Regulation FCC Notice FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
WEEE Decla aration Disposal of o Waste Equipment by Use ers in Private Household in the European n Union. This symb bol on the product or on its packaging ind dicates that thiis product musst not be dispo osed of with your y other household d waste. Inste ead, it is your responsibility r t dispose of your to y waste eq quipment by ha anding it over to a designate ed collection point for the reccycling of wasste electrical and a electronic equipment.
EPA Energy Star ENERGY STAR® is a U.S. registered mark. As an ENERGY STAR® Partner, AOC International (Europe) BV and Envision Peripherals, Inc. have determined that this product meets the ENERGY STAR® guidelines for energy efficiency. (FOR EPA CERTIFIED MODELS) This product is compliant with requirements of Circular No.
Waste Electrical and Electronic Equipment- WEEE This marking on the product or on its packaging illustrates that, under European Directive 2012/19/EU governing used electrical and electronic appliances ,this product may not be disposed of with normal household waste .You are responsible for disposal of this equipment through a designated waste electrical and electronic equipment collection.
TCO DOCUMENT (FOR TCO CERTIFIED MODELS) 60
Service EU WARRANTY FOR AOC MONITORS LIMITED THREE-YEAR WARRANTY* For AOC LCD Monitors sold within Europe, AOC International (Europe) B.V. warrants this product to be free from defects in material and workmanship for a period of Three (3) years after the original date of consumer purchase. During this period, AOC International (Europe) B.V. will, at its option, either repair the defective product with new or rebuilt parts, or replace it with a new or rebuilt product at no charge except as *stated below.
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO A PERIOD OF THREE (3) YEARS FOR PARTS AND LABOR FROM THE ORIGINAL DATE OF CONSUMER PURCHASE. NO WARRANTIES (EITHER EXPRESSED OR IMPLIED) APPLY AFTER THIS PERIOD. AOC INTERNATIONAL (EUROPE) B.V. OBLIGATIONS AND YOUR REMEDIES HEREUNDER ARE SOLELY AND EXCULSIVELY AS STATED HERE. AOC INTERNATIONAL (EUROPE) B.V.
Warranty Statement for North & South America (excluding Brazil) WARRANTY STATEMENT for AOC Color Monitors Including those Sold within North America as Specified Envision Peripherals, Inc. warrants this product to be free from defects in material and workmanship for a period of three (3) years for parts & labor and one (1) year for CRT Tube or LCD Panel after the original date of consumer purchase. During this period, EPI ( EPI is the abbreviation of Envision Peripherals, Inc.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO A PERIOD OF THREE (3) YEARS FOR PARTS AND LABOR AND ONE (1) YEAR FOR CRT TUBE OR LCD PANEL FROM THE ORIGINAL DATE OF CONSUMER PURCHASE. NO WARRANTIES (EITHER EXPRESSED OR IMPLIED) APPLY AFTER THIS PERIOD.
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following tes t methods have been appliedin order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: - EN60950-1 Safety of Information Technology Equipment - EN 62311 Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0 Hz-300 GHz) - EN 300 328 ( For 802.
CE Declaration of Conformity This product is in conformity with the following standards • EN60950-1:2006+A11:2009+A1:2010+A12:2011 (Safety requirement of Information Technology Equipment). • EN55022:2010 (Radio Disturbance requirement of Information Technology Equipment). • EN55024:2010 (Immunity requirement of Information Technology Equipment). • • EN61000-3-2:2006 +A1:2009+A2:2009 (Limits for Harmonic Current Emission).
Only for AOC branded monitors sold within the continental United States. All AOC branded monitors are now covered by the EASE Program. If your monitor malfunctions at any time during the first three months, AOC will provide a replacement monitor within 72 hours after you are approved for our program. If your monitor qualifies for the EASE program, AOC will pay for freight both ways. Step 1: Phone our TECH Department at 888.662.9888 Step 2: Fill out and return EASE registration forms by mail or fax.
