23" LCD Color Monitor AOC i2430Ve Service Service Service Horizontal Frequency 30-83 kHz TABLE OF CONTENTS Description Page Description Page Table of Contents…………………..…………………..…...1 6.3.Key Board..……….........................................32 Revision List.…...................................................……......2 6.4.Light Sensor Board...............................................33 Important Safety Notice.….….............................……......3 7.PCB Layout..………........................
Revision List Revision Date Revision History Remark TDAGNT2EWWA4HNE A00 Jan.
Important Safety Notice Proper service and repair is important to the safe, reliable operation of all AOC Company Equipment. The service procedures recommended by AOC and described in this service manual are effective methods of performing service operations. Some of these service operations require the use of tools specially designed for the purpose. The special tools should be used when and as recommended.
Monitor Specifications 4
LCD Monitor Description The LCD MONITOR will contain a main board, a power board, a key board which house the flat panel control logic, brightness control logic and DDC. The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips each voltage. Monitor Block Diagram LED Drive.
3. Operating Instructions 3.1 General Instructions Press the power button to turn the monitor on or off. The other control knobs are located at front panel of the monitor (See Figure ). By changing these settings, the picture can be adjusted to your personal preferences. * The power cord should be connected. * Press the power button to turn on the monitor. The power indicator will light up. 3.
1.Power 2.Analog (DB-15 VGA cable) 3.Power To protect equipment, always turn off the PC and LCD monitor before connecting. 1. Connect the power cable to the AC port on the back of the monitor. 2. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer's D-Sub port. 3. (Optional – Requires a video card with DVI port) - Connect one end of the DVI cable to the back of the monitor and connect the other end to the computer‟s DVI port. 4.
3.3 OSD Setting 1) Press the MENU-button to activate the OSD window. 2) Press ◄ or ► to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate sub-menu . Once the desired function is highlighted, press MENU-button to activate it. 3) Press ◄ or ► to change the settings of the selected function. Press ◄ or ► to select another function in sub-menu . Press AUTO to exit . If you want to adjust any other function, repeat steps 2-3.
Luminance Press (Menu) to display menu. Press Menu to display MENU Press ◄ or ► to select press (Luminance), and to enter. Press ◄ or ►to select submenu, press enter, and press ◄ or ► to adjust. Press to exit.
Brightness 0-100 Backlight Adjustment Contrast 0-100 Contrast from Digital-register.
Image Setup Press (Menu) to display menu. Press ◄ or ► to select and press (Image Setup), to enter. Press ◄ or ► to select submenu, press enter, and press ◄ or ► to adjust. Press to to exit. Clock 0-100 Adjust picture Clock to reduce Vertical-Line noise. Phase 0-100 Adjust Picture Phase to reduce Horizontal-Line noise H.Position 0-100 Adjust the horizontal position of the picture. V.Position 0-100 Adjust the vertical position of the picture.
Color Temperature Press (Menu) to display menu. Press ◄ or ► to select (Color Temperature), and press to enter. Press ◄ or ► to select submenu, press enter, and press ◄ or ► to adjust. Press to to exit. Warm 6500K Recall Warm Color Temperature from EEPROM. Normal 7300K Recall Normal Color Temperature from EEPROM. Cool 9300K Recall Cool Color Temperature from EEPROM. sRGB User Recall SRGB Color Temperature from EEPROM.
Color Boost Press (Menu) to display menu. Press ◄ or ► to select and press (Color Boost), to enter. Press ◄ or ► to select submenu, press enter, and press ◄ or ► to adjust. Press to to exit.
Picture Boost Press (Menu) to display MENU. Press ◄ or ► to select press (Picture Boost); and to enter. Press ◄ or ► to select Bright Frame. Select “on” to activate Picture Boost. Press ◄ or ► to select submenu, press enter, and press ◄ or ► to adjust. Press to exit. Frame Size 14-100 Adjust Frame Size Brightness 0-100 Adjust Frame Brightness Contrast 0-100 Adjust Frame Contrast H. position 0-100 Adjust Frame horizontal Position V.
OSD Setup Press (Menu) to display menu. Press ◄ or ► to select and press (OSD Setup), to enter. Press ◄ or ► to select submenu, press enter, and press ◄ or ► to adjust. Press to exit. OSD Setup H.Position 0-100 Adjust the horizontal position of OSD V.
Extra Press (Menu) to display menu. Press ◄ or ► to select and press (OSD Setup), to enter. Press ◄ or ► to select submenu, press to enter, and press ◄ or ► to adjust. Press 16 to exit.
Auto Select to Auto Detect input signal Analog Select Analog Sigal Source as Input Digital Select Digital Sigal Source as Input Auto Config yes or no Auto adjust the picture to default Image Ratio wide or 4:3 Select wide or 4:3 format for display DDC-CI yes or no Turn ON/OFF DDC-CI Support Off Timer 0~24hours Select timing to turn off the monitor.
Reset Press (Menu) to display menu. Press ◄ or ► to select press (Reset), and to enter. Press◄ or ► to select YES or NO. Press Reset yes or no to exit.
Exit Press (Menu) to display menu. Press ◄ or ► to select to enter.
4. Input/Output Specification 4.1 Input Signal Connector Analog connectors Pin Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 15-Pin Side of the Signal Cable Video-Red Video-Green Video-Blue N.C. Detect Cable GND-R GND-G GND-B +5V Ground N.C. DDC-Serial data H-sync V-sync DDC-Serial clock DVI connectors Pin No. 1 2 3 4 5 6 7 8 Signal Name TMDS Data 2TMDS Data 2+ TMDS Data 2/4 Shield TMDS Data 4TMDS Data 4+ DDC Clock DDC Data N.C. Pin No.
4.
4.3 Panel Specification 4.3.1 General Features LM230WF3 is a Color Active Matrix Liquid Crystal Display with a Light Emitting Diode ( White LED) backlight The matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type display operating in the normally black mode.
(Ta=25 °C, VLCD=5V, fV=60Hz Dclk=144MHz, IBL=110mA) 23
5. Block Diagram 5.
5.2 Power Board AC input EMI filter Transformer Bridge Rectifier and Filter 14.5V Rectifier diodes (T901) 5V Start Resistor (R904) Power Switch (Q901) PWM Control LD7750GS (IC901) Photo coupler (IC903) 14.
6. Schematic 6.1 Main Board 715G4002M01000004S FB102 0R05 1/10W R103 100OHM1/16W R104 100OHM1/16W R106 2.2K 1/16W R107 2.2K 1/16W C103 22P 50V C104 22P 50V R101 10 5 9 4 8 3 7 2 6 1 DSUB_SCL 15 14 100OHM1/16W 13 DSUB_SDA 12 100OHM1/16W FB103 VGA_G+ V_Sy nc C125 100N 16V VGA_BVGA_B+ ZD101 VGA_G- RLZ5.
PA[0..9] 5 PB[0..9] PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 PA8 PA9 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1 PB[0..9] PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 PB8 PB9 LVA3P LVA3M LVACKP LVACKM LVA2P LVA2M LVA1P LVA1M LVA0P LVA0M LVB3P LVB3M LVBCKP LVBCKM LVB2P LVB2M LVB1P LVB1M LVB0P LVB0M LVB0M LVB1M LVB2M LVBCKM LVB3M LVA0M LVA1M LVA2M LVACKM LVA3M RXO0RXO1RXO2RXOCRXO3RXE0RXE1RXE2RXECRXE3- CONN 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2 RXO0+ RXO1+ RXO2+ RXOC+ RXO3+ RXE0+ RXE1+ RXE2+ RXEC+ RXE3+ 31 5 PA[0..
SOT 252 12 VIN VOUT(TAB) ADJ(GND) 1 +12V 1 2 3 4 5 6 7 8 9 10 U702 G1117-33T43UF 3 2 1 2 D707 SR34 Both 223 and 252 foot-print CMVCC1 1 R707 0R05 1/10W BKLT-VBRI BKLT-EN D708 SR34 R708 NC/0R05 1/10W 5% CONN SOT 223 2 11 CMVCC1 CN702 VCC3.3 U701 3 VO Dropout voltage must < 0.8V @ 600mA 2 GND VI C709 100N 16V 1 C708 100N 16V C707 22UF 16V VCC3.3 VCC3.3 1 CMVCC1 SOT 223 D703 SR34 R703 10K+-5%1/16W 3 VI VO Dropout voltage must < 0.
VCC1.8 VCC3.3 CVDD VCC3.3 2,4 AVCC VCC3.3 DVDD ADC_VAA AVCC CVDD FB401 0R05OHM1/8W 4 VCC1.
6.2 Power Board Adapter 715G 901 2 4A 51 OHM +-5% 1/4W R923 51 OHM +-5% 1/4W R913 R912 51 OHM +-5% 1/4W 430K 1/4W C926 R922 R967 430K 1/4W 2 430K 1/4W 1 ! + - BD901 GBU408 C904 100uF 450V T901 8 2N2 500V L902 1.1uH 2 +12V 2 C925 R904 10nF 1N4007 D902 4 47KOHM +-5% 1/4W C922 D901 1N4007 R907 3 9 10 4 5 2R2 1/4W 5% C919 + 680UF 25V R924 + C921 (NC)10K 1/8W 5% 680UF 25V C920 4.7uF/25V C918 NC 6 + C906 C909 3300pF 250V 47uF/50V 7 11 更改料件 1 0.
Converter 715G4119P01002004C GATE Q806 1 2 3 4 CN801 8 7 6 5 D801 L801 1 2 11 22uH 12 ON/OFF DIM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 C801 0.47uF 50V R806 1K 1/10W C802 68NF 50V R807 100K 1/10W R808 1K 1/10W R810 100K 1/10W R818 0R05 1/4W C808 NC R802 200K 1/10W 5% R803 30K 1/10W 1% +14.
6.3 Key Board 2 3 1 715G4014K01000004C LED001 LED 0.1uF 50V 0R01 1/10W R003 R004 2KOHM 1% 1/10W 1K 1/10W SGND SW005 SW OK LBADC2 LBADC1 MENU C002 0.1uF 50V 2KOHM 1% 1/10W R002 AUTO CONN C001 R001 UP LBADC1 LBADC2 DC_POWERON LED_1# LED_2# DOWN 1 2 3 4 5 6 SW004 SW POWER CN001 SW003 SW SW002 SW SW001 SW (2.0K) 1.118V AUTO(0) 0V DOWN(2K) 1.118V MENU(1K) 0.
6.4 Light Sensor Board 715G3995T01000004C VCC R017 NC R014 1K 1/16W 5% 5 + 7 R012 NC/100R 1/16W 5% R015 100K 1/16W 5% 6 - U012B LM358DR R026 NC 3 + 1 IR_TX R011 NC/100R 1/16W 5% 2 - U012A LM358DR 1 VCC_IN VCC_IN R018 33 OHM 1/8W R023 33 OHM 1/8W C015 100N 16V C020 100N 16V VCC_IN 2 R020 1K 1/16W 5% Q012 SST2222A SEN_ON R021 1K 1/16W 5% 1 VCC Q011 MMBT2907AK 3 R019 1K 1/16W 5% NC/UDZSNP5.6B ZD012 1 2 2 R016 100K1/16W 2 LED011 LED NC/UDZSNP5.6B ZD013 1 2 NC/UDZSNP5.
7. PCB Layout 7.
7.
Converter 715G4119P01002004C 36
7.3 Key Board 715G3371 2 7.
8. Maintainability 8.1 Equipments and Tools Requirement 1. Voltmeter. 2. Oscilloscope. 3. Pattern Generator. 4. DDC Tool with an IBM Compatible Computer. 5. Alignment Tool. 6. LCD Color Analyzer. 7. Service Manual. 8. User Manual.
8.2 Trouble Shooting 1.
2.
3.
4.
9. FOS Testing 9.1 Brightness Measurement Max. Brightness>250 cd/㎡(typ). Test conditions: - Center of display - Video input (RGB) = 0,700V for Analog Input - Brightness control is set to max - Contrast control is set to max. Min. brightness measurement: < 45% of Max luminance (max luminance = max contrast + max brightness) Test conditions: - Center of display - Video input (RGB) = 0.700V for Analog Input - Brightness control is set to min. - Contrast control is set to min. 9.
Cross line Half line H-Line V-Line H-Strip 1. 1920x1080 (60 Hz) 2. Black pattern 1. 1920x1080 (60 Hz) 2. Black pattern or White pattern 1. 1920x1080 (60 Hz) 2. Black pattern, Red pattern, Green pattern or Blue pattern. 1. 1920x1080 (60 Hz) 2. Black pattern or White pattern 1 1920x1080 (60 Hz) 2. Black pattern, Gray scale pattern, Red pattern, Green pattern or blue pattern .
V-Strip 1. 1920x1080 (60 Hz) 2. Black pattern, Gray scale pattern, Red pattern, Green pattern or blue pattern . Abnormal display 1. 1920x1080 (60 Hz) 2. Gray scale pattern Gray defect 1. 1920x1080 (60 Hz) 2. Gray scale pattern Video noise 1. 1920x1080 (60 Hz) 2. Gray scale pattern Color tint 1. 1920x1080 (60 Hz) 2.
Gray scale failure Light leakage Fuzzy video 1. 1920x1080 (60 Hz) 2. Gray scale pattern 1. 1920x1080 (60 Hz) 2. Black pattern or White pattern 1. 1920x1080 (60 Hz) 2.
10.Firmware and DDC Instruction 10.1Firmware Instruction(TSUM IC ISP for exemple NT68676) Step 1:OPERATION CONDITIONS: 1) An i486 (or above) personal computer or compatible. 2) Microsoft operation system Windows 95/98/2000/XP. 3) ISPTool programs programs. 4) Printer cable and VGA cable. 5) ISP board (PN: 715GT034-B,715GT048-1 or715GT035-A). 6) ISP Firmware/Software Step 2:Connection: 1) LPT cable connect PC and ISP board ; 2) VGA cable connect monitor and ISP board ; 3) Reference picture as below NO1.
ISP TOOL front side ISP TOOL reverse side Step 3: Programming: 1. Double-click the icon to install Port95nt print driver, 2. Install tool programme 2.1 decompress PS:NT68168F Scale IC must use V4.566 version. 2.2 Double-click 3. ISP Tool 3.1. Choose ”writer” as follow picture. 48 .
3.2.Double-click icon and run it: 4.
5.Click tool “Option” choose” Setup ISP tool” and then choose LPT Port,the next ,choose NVT Type (default),click “Auto Detect”to choose the appropriate speed。Click”Confirm change”。 6.
Click“Auto” AUTO Click “Send MX2026 CMD” Click“AUTO”,when appear “pass” as follow picture that burning is successful: 51
Note: After installation, you must restart the PC to take the setup to effect. Step4:Check whether the FW version is correct, then do “Auto Color” and “Reset”. a. For VGA, if can’t use the recommended optimal resolution; for DVI, if no video with PC source, while picture is normal with chroma source, it’s the reason for “DDC Loss”, so pls do DDC programming. b.
II. HDCP Write Step: Step1. Double click “HDCP20091026.exe” Step2. Click “Load HDCP…”. choose the corresponding “*.BIN” by scaler IC (MST Scaler) ,then click “Open” as below.
Step3. Pls choose the item remarked in red (i.e.: New CMD/Only Connect One Monitor/MST Scaler), then click “Start” to write HDCP, when display “Monitor 1 PASS” means Write OK.
III. Check HDCP. USE “Blu-Ray Disc” DVD to check whether the monitor with DVI connector displays normally. If error message appeared “ ” as below: 1. Check whether the HDCP writer is correct. 2. Check whether the tool is correct or not, and check the connection between PC, Monitor and tool. In addition, check whether the tool’s power supply is available. 3. If still no work, pls modify the “config.ini” as below, and then try again. Modify Step: Right click “config.
350 ->500 150 ->300 500 ->700 57
10.2 DDC Instruction Tool list: 1. DDC board:715GT034-B 2. Software (WA.DAT&WD.DAT&*. CONFIG.INI) 3. LPT driver software 4. LPT cable, D-SUB CABLE ,DVI CABLE and DVI to HDMI CABLE 5. 12V( Adapter) 6. TPVDDCHDMI and TPVDDC6.0 7.
VGA&DVI Burning: 1.Double-click the icon “ Double-click ” to install Port95nt print driver, and then restart the computer. , select “Analog and DVI” show as follow picture 2. Click “Load file” and select as follow picture.
3. Click “ok” show as follow picture. 4.Input same SN twice and date. Click “Pragram” to burn. When appear “pass” as follow picture that burning is successful.
5. Click “program”, Note:1. Appear fault as follow , please input SN twice and burning again.
Note:2. When appear “pass” as follow picture that burning is successful. Note3:Click “Read both” show as follow picuture..If read SN and model name are same as before inputing as before that burning is successful.
Note4:Appear fault as follow, please check the connection of LPT cable , Tool adapter cable and LCD power.
Note6: If the burn software is unsuccessfulll, appear fault: 1. For VGA,the resolution will be not the best achieve. 2. For DVI,No picture,no sound. If program failed, in VGA mode, you can’t use the optimal resolution. When Read is OK, program is NG, pls do take following action: 1. For VGA,cut off the 9th pin (connect the monitor). 2. For DVI, cut off the 14th pin (the shortest pin, power supply). 3. Connect the EEPROM WP pin to ground.
11. White- Balance, Luminance Adjustment Approximately 30 minutes should be allowed for warm up before proceeding white balance adjustment. How to setting MEM channel you can reference to chroma 7120 user guide or simple use “SC” key and “NEXT” Key to modify xyY value and use “ID” key to modify the TEXT description Following is the procedure to do white-balance adjust . 1. Setting the color temp. A. 6500K color Warm color temp. parameter is x=313±30, y=329±30, Y>150cd/ m2(typ) B.
C. Adjust Cool (9300K) color-temperature 1. Switch the Chroma-7120 to RGB-Mode (with press “MODE” button) 2. Switch the MEM. Channel to Channel 9 (with up or down arrow on chroma 7120) 3. The LCD-indicator on chroma 7120 will show x=283±30, y=297±30, Y>150cd/ m2(typ) 4. Adjust the RED on factory window until chroma 7120 indicator reached the value R=100 5. Adjust the GREEN on factory window until chroma 7120 indicator reached the value G=100 6.
12. Mechanical Instructions 1. Put monitor on the EPE cushion 2. Put monitor front side upwards and top side face to yourself.
3.Open the top side of front bezel with fingers. 4. Open whole front bezel with a special disassembly tool.
5.Put panel side downwards and take off back cover 6.Remove lamp cable\ aluminum foil\KEPC\ e-SENSOR BOARD\ hexagonal screws.
7.
8.
13.
14. BOM List Note: The parts information listed below are for reference only, and are subject to change without notice. Please go to http://cs.tpv.com.cn/hello1.asp for the latest information. TDAGNT2EWWA4HNE Location HDCP-L E09504 E09501 E09501 E09503 E09503 E09502 E09502 E09505 E09505 E750 E09504 Part No.
SMTCA-U402 E08903 E08903 E08903 E08901 C718 C716 FB702 CN701 CN101 CN102 X401 CN402 CN401 CN702 U401 U704 U705 U702 U103 U104 U105 U106 U107 U102 U101 U402 Q401 Q402 Q302 Q701 Q301 R406 R408 R427 R115 R111 R105 R134 R132 A34G1865DBA 1B0100 A34G1866DBA 1B0100 A34G2366DAV 1M0100 A37G0164012 756GHACB A1073 100GANGD000W11 808GI2340VETPE 089G1745CAA 9 089G1745GAA 9 089G1745HAA 9 089G420A15N IS H26G 800504 2B H40G 24N61538A H40G 58261572A H40G 58461536A H41G780961540A CBPC9NRA1H5 040G 45762412B 067G204V181 3K
R131 R130 R129 R128 R127 R126 R706 R435 R420 R419 R401 R119 R118 R113 R104 R103 R101 R437 R436 R426 R413 R412 R705 R703 R702 R418 R417 R403 R402 R305 R120 R726 R712 R415 R306 R135 R434 R714 R106 R107 R704 R304 R136 R123 R139 R416 R727 R711 R433 R432 R431 R133 R109 R114 R117 061G0402100 JY 061G0402100 JY 061G0402100 JY 061G0402100 JY 061G0402100 JY 061G0402100 JY 061G0402101 JY 061G0402101 JY 061G0402101 JY 061G0402101 JY 061G0402101 JY 061G0402101 JY 061G0402101 JY 061G0402101 JY 061G0402101 JY 061G0402101
R414 R110 R422 R411 R410 R303 R138 R137 R125 R124 R713 R108 R112 R116 R707 R102 FB703 FB103 FB102 FB101 R404 R405 FB401 R302 R301 C107 C118 C119 C714 C422 C425 C427 C431 C432 C433 C434 C435 C437 C438 C702 C705 C706 C708 C709 C713 C717 C720 C112 C115 C120 C121 C122 C124 C125 C126 061G04024700FY 061G0402471 JY 061G0402472 JY 061G0402472 JY 061G0402472 JY 061G0402472 JY 061G0402472 JY 061G0402472 JY 061G0402472 JY 061G0402472 JY 061G04026801FY 061G0402750 JY 061G0402750 JY 061G0402750 JY 061G0603000 JF 061G06
C301 C419 C418 C417 C407 C405 C403 C402 C401 C304 C712 C719 C722 C103 C104 C429 C303 C117 C116 C428 C426 C114 C111 C110 C108 C106 C102 C105 C109 C113 C715 C710 C305 C408 C414 C415 C424 C439 C423 C421 C416 C413 C406 C404 C721 C723 C302 C704 C707 FB301 FB407 FB405 FB404 FB403 FB402 065G040210412K 065G040210412K 065G040210412K 065G040210412K 065G040210412K 065G040210412K 065G040210412K 065G040210412K 065G040210412K 065G040210412K 065G040210427Z 065G040210427Z 065G040215131J 065G040222031J 065G040222031J 065G0
FB104 FB105 FB106 L701 D101 D102 ZD101 D708 D707 D704 D701 D703 CN301 E080 IC903 NR901 C903 C925 C902 C901 C909 C919 C921 C904 D901 D902 D904 Q901 L902 L901 T901 LED2 CN901 D902 D901 GND1 GND2 GND4 GND3 071G 59G301 071G 59G301 071G 59G301 073G253S521 H 093G 64 42 L 093G 64 42 L 093G 39GA01 T 093G3004 3 093G3004 3 093G3004 3 093G3004 3 093G3004 3 311GW125A30ACH 715G4002M01000004S ADPCA1248HD1 040G 154501 1 040G 45762412B 045G 88525 E 052G 1211 A 056G 139 3A 061G 58901 WT 063G107K474 6S 065G 1K103 2E6921 0
BD901 D904 HS1 Q901 HS2 E55 IC901 R968 C908 R986 R909 R916 R920 R910 R921 R907 R967 R922 R914 R906 R908 R917 R904 R923 R913 R912 R918 R903 R902 R901 R919 C911 C922 C923 C915 C912 C914 C916 C920 T901 CN901 L901 IC904 R911 C926 C906 F901 J901 Q52G 1205106 093G 50460900 005G 42 1 012G 372 1 093G 60310 0M1G 930 6120 Q90G0171 1 057G 667924 0M1G 930 6120 Q90G0168 1 055G 23524 Q51G 6 4509 Q55G 100625 056G 379530 061G0603222 JT 061G0805104 JT 061G0805203 JT 061G0805221 JT 061G08052491FT 061G1206100 JT 061G120610
J902 J903 SW001 SW002 SW003 SW004 SW005 CN001 R002 R004 R003 R001 C002 C001 LED001 E715 E715 C807 C809 CN803 CN801 U801 Q806 R832 R833 R819 R806 R808 R822 R804 R807 R810 R803 R802 R809 R826 R838 R837 R836 R835 R815 R805 R818 R812 R813 R801 C806 C802 C805 095G 90 23 095G 90 23 709G 901 HA001 715G 901 2 156403 KEPC9HC2 077G603S AI HJ 077G603S AI HJ 077G603S AI HJ 077G603S AI HJ 077G603S AI HJ 033G8032 6F HR 061G0603000 FF 061G06031001FF 061G06032001FF 061G06032001FF 065G060310432K A 065G060310432K A 081G 1
C804 C803 C801 L801 D801 U013 C019 LED011 U012 U011 Q011 Q012 Q013 R025 R027 R021 R020 R019 R014 R022 R024 R015 R016 R013 R023 R018 C012 C013 C015 C016 C017 C018 C020 C011 E715 CN011 E715 065G080547332K Y 065G080547332K Y 065G080547422K Y 073G253S 19 H 093G 60S907 T 715G4119P01002004C LSPC9HC2 056G 627911 067G305M1013KV 081G IR 7 GP H12G6200 13 056G 192 25 056G1125200 057G 417 16 T 057G 761 18 T 057G 761 18 T 061G0402101 JY 061G0402102 JY 061G0402102 JY 061G0402102 JY 061G0402102 JY 061G0402102 JY 061G040