LED LCD TV User Manual LE42K09D/ LE42H09P ww w.aoc.com 2010 AOC. All Rights Reserved.
This manual is provided as an operational guide to user. All statements, technical information, and recommendations in this manual and in any guides or related documents are believed reliable, but the accuracy and completeness thereof are not guaranteed or warranted, and they are not intended to be, nor should they be understood to be,representations or warranties concerning the products described.
Contents Important information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Operating AOC TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Power on/off the TV set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Caution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 First time setting. . .
Important information Important safety information Warning 2. Pay attention to all warnings. 1. Read and keep these instructions. 3. Follow all operation instructions. 4. Make sure that only proper power supply is used CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION RISQUE DE CHOC ELECTRIQUE, NE PAS OUVRIR PRECAUCION RIESGO DE CHOQUE ELECTRICO NO ABRIR This sign is intended to warn the user that uninsulated, dangerous voltage inside the TV may result in electric shock. 5.
Usage Instructions Accessories Do not use accessories not recommended by the product manufacturer in order to avoid risks. Installation Wall-mount Placement Wall-mount brackets need to be used for wall-mount TV sets. Be sure to ask qualified contractors to carry out installation when using wall-mount brackets to install or remove a TV set. Improper installation or removal of wall-mount brackets may result in TV sets falling and severe personal injury.
LED screen • • • • • • • • • Electric shock Do not touch the AC power cord or the TV set with a wet hand. Plugging in or unplugging the AC power cord with a wet hand may result in electric shock. Although the LED screen is manufactured by state-ofthe-art technologies, with effective pixels reaching up to 99.99% or even higher, black spots or bright spots such as red, blue and green may appear on the LED screen continuously. This is the structure nature of the LED panel rather than a failure.
Small accessories Cleaning Clean the plug of the AC power supply. Place small accessories out of children’s reach. Pull out the AC power supply plug and clean it regularly. If there is too much dirt on the plug, it will absorb moisture and its insulation property will decline, thus resulting in a fire. Clean the TV set screen/casing • Unplug the AC power cord to avoid electric shock during cleaning.
Moving the TV set 30 cm Move the TV set as per the specified below Be sure to follow the following instructions to avoid the TV set from falling and severe personal injury: • • • 4 inches 10 cm Disconnect all cables before moving the TV set. Moving a large-size TV set needs two or more persons. Hold the position as indicated in the figure below when moving the TV set. Do not press the LED panel. Install the TV set with a stand base. 10 cm Such a space shall be provided at least around the TV set.
Volume adjustment Adjust the TV set volume so as not to affect neighbors as sound seems to be transmitted easily at night. It is recommended to close the window or use a pair of earphones. is a trademark of SRS Labs, Inc.TruSurround HD technology is incorporated under license from SRS Labs, Inc. Adjust the volume to an appropriate level when using earphones to prevent overly loud sounds from impairing your hearing.
Packing list Check the TV set and all accessories for their intactness after the packing case is opened.
Control and connection e f g Touch type h i Channel a b c Volume d Source Menu Power supply Item Description a YPbPr input Used to connect the YPbPr jack and L/R jack input from other device. The YPbPr will provide better picture quality than S terminal or composite video. b SPDIF Output a digital audio to the external loudspeaker or other digital audio equipment c Antenna input RF input used to connect the cable or VHF/UHF antenna.
Remote control a TV n o Freeze AV YPbPr Picture PC Audio USB I/II Sleep Dispaly q Keys Description f Program +/- Press the key to change channels. Press either of +/- keys and hold to switch channels rapidly. g Mute b h Sleep l k h Press oœpπ keys to select Picture/Music/ AV under the multimedia thumbnail option. i Zoom Menu i j e VOL CH OK f j Menu k Audio c l I/II Back Press the key to confirm the item and settings selected.
Battery installation for the remote control Put two AAA batteries (supplied) into the position indicated in the battery case of the remote control. Installation Refer to the above schematic diagram for important operation instructions. Stand base installation Install the stand base (sold separately) before installing the TV set. Carry out the installation pursuant to the following simple procedures: 42”: 1. Disconnect all cables from the TV set. 2.
Wall-mount • Use wall-mount brackets (sold separately) to install the TV set on the wall. Be sure to remove the stand base of the TV set before installing it. • Do not remove the stand base unless the TV set is mount on the wall. • First remove four M6(42”) screws before installing wall-mounted brackets. • Be sure to keep the screws and the removed stand base properly for future use. Place screws out of children’s reach.
Connections to TV Cable system or VHF/UHF antenna system Besides standard definition analog programs, you may also watch standard definition or high definition digital programs (if such programs are available in your region). The TV set can receive cable and VHF/UHF antenna analog signal TV programs. AOC strongly recommend to use 75Ω coaxial cable connected antenna/cable input to receive optimum picture quality.
YPbPr connection YPbPr input AV signal connection AV signal input Computer connection TV set can be used as a computer monitor by connecting TV to computer with a VGA cable.The TV set may also be connected to a computer with HDMI output. Computer signal input • Use the VGA cable and an audio cable with ferrite core to connect the TV set to the computer.
Reference sheet of computer input signals Set output signals in the computer according to the table below after connecting the computer to the TV set properly. Definition Horizontal frequency (kHz) 640 x 480 31.469 Vertical frequency (Hz) 59.940 800 x 600 37.879 60.317 1024 x 768 48.363 60.004 1360 x 768 47.720 59.799 1280 X 1024 63.981 60.000 1920 X 1080 66.587 59.934 Reference sheet of computer HDMI input signals 1.
AV system supported by TV: PAL D/K B/G I ; NTSC M/N。 Standard definition interface You may watch conventional programs by DVD player or VCR player. Connect the equipment to the TV set via AV input at the side of the TV set panel. Operating AOC TV set Power on/off the TV set You may turn on the TV set via the power button on the TV set or the remote control. TV AV YPbPr PC Freeze Picture Audio Dispaly • • • •USB I/II Sleep Channel Volume Source Menu Power supply Touch type Tips 1.
Step2 : TV pops-up window shown below prompting to select Menu Language. By default English will be selected as Menu language to continue wizard press OK key or πarrow key on remote control or to select languages other then English pressoœarrow key and press Ok key. To exit from initial setup wizard press Menu key. Step3 : TV pops-up window shown below prompting for Auto scan of channel. If RF input is connected to TV select [Scan] and press OK key or πarrow key to scan for VHF/UHF channels automatically.
Switch between input sources You can select signal sources to your AOC TV set directly with your remote controller. You can also press the Source key in the display menu to select signal source. 1. When selecting a source with a remote control directly: Press the following keys to switch input sources directly. TV AV YPbPr HDMI/ PC USB Freeze Picture Audio I/II Sleep Dispaly 2.
Picture settings Picture Auto picture Standard Brightness 50 Contrast 50 Color 50 Tint 0 Sharpness Item Smart image 5 Description Personal settings User can set their favorite setting. Standard Standard picture setting. Recommended for family entertainment. Vivid Enhanced picture contrast and sharpness. Movie Used to watch movie based content. Most suitable for cinema environment. Energy saving Reduce the backlight intensity to save electricity.
Picture settings (For computer source only) Advanced Video Auto Config Horizontal 64 Vertical 48 Phase 4 Clock 127 Resolution Item Description Auto adjustment Adjust the picture to optimum position of the screen automatically. Horizontal position Adjust the horizontal position of the picture. Vertical position Adjust the vertical position of the picture. Phase Adjust the phase of the computer output signal. Clock Adjust the clock frequency of computer signals.
Sound setting Sound Auto sound Personal Equalizer 120Hz 0 Equalizer 500 Hz 0 Equalizer 1.5 KHz 0 Equalizer 5 kHz 0 Equalizer 10 kHz 0 AOC co-works with SRS Labs to create unique and exclusive sound technology- DSS Dream Surround. DSS effect creates a truly immersive surround sound experience with rich bass and clear dialog from only two speakers. Item Description Smart sound Person setting: Provide the sound mode set by the user.
Features settings Features Menu Language Simplified Chinese Picture Format Time Auto Parental Reset SW Ver. V1.000A Item Description Menu language Press the pπ key to select the required language and press the OK key to confirm it. Picture format To select the available picture format. Time Wide screen, Auto, Normal, Zoom1 and Zoom2 Sleep timer can be set to 5, 10, 15, 30, 45, 60, 90, 120 minutes. Tips: 1. The TV switches to standby after the specified time. 2.
TV settings The setting is available only in TV mode. TV Channel Scan Manual Scan Channel Skip Channel Sort Channel Edit Channel Fine Tune Item Description Channel scan TV automatically searches for the channel in the available frequency band and stores sequentially Press the OK key to enter the interface. Press the pπ to select [Yes] and press the OK key to start scanning channels. Scan the wireless channels or cable channels the TV set can receive in your area automatically.
Multimedia functions (USB) TV USB port can be used to view JPEG photos, play mp3 music and Video files present in USB devices. Selecting USB Media Center: Press the USB Direct USB key on remote to enter into the [USB] source OR Source 1. Press the key to display the source menu. 2. Press the key to select [USB] source. and press the OK key to enter into USB source. USB menu settings When USB drive is detected by the TV, USB drive is displayed as a folder on the screen as shown below.
USB menu settings for JPEG Press the Menu key to get the following menu settings: 1. [Pause/Play] : Use to pause or play the slide show. 2. [Repeat] : Use to select the following repeat options: a. Repeat one : show same image repeatedly. b. Repeat all : show all the images in the folder repeatedly. 3. [ Shauffle On/Off] : When shauffle is on slideshow will display images randomly and if shauffle is off slideshow displays imagesone after the other according to sort order 4.
Tips: 1. The USB interface to the digital multimedia player is not universal. If a file fails to be identified by the USB interface, it is normal and related to the equipment drive. 2. The period needed for the player to read information varies with the equipment and its memory capacity and information reading speed may slow down temporarily. This is a normal phenomenon. 3. The USB interface of the equipment provides 5V voltage and 500Ma maximal current.
Dimensions and specifications Model LE42K09D LE42H09P Panel display size 930.24(H) x 523.26(V) (42.02”diagonal) 930.24(H) x 523.26(V) (42.
Troubleshooting Symptoms Explanation/solution No picture is available. Check the energy saving settings. Fail to receive any channel. Ensure proper power cord connection. Turn on the TV set. Check antenna/cable connection. Ensure your TV source cable settings are correct. The TV set is locked in a certain channel. Execute auto program searching and add available channels not saved in the TV channel memory. Fail to receive or select channels.
Symptoms Explanation/solution Computer input Identify that the computer has been connected to the TV set properly via computer output (with the HD cable) or the HDMI output. No picture/no signal. Ensure that the output signal in the computer is a format listed in the signal reference sheet. Turn off the computer. Identify that the computer is connected properly and restart the computer. The plug-and-play equipment will detect the TV set automatically and set the computer resolution properly.
