Service manual

ManualsBrandsAOC ManualsMonitorse2450Swd

Service Manual e2450Swd

AOC 显示器维修手册

Model: e2450Swd

Summary of content (65 pages)

PAGE 1
Service Manual e2450Swd AOC 显示器维修手册 Model: 1 e2450Swd
PAGE 2
Service Manual e2450Swd Revision List Version Release Date Revision History TPV Model Name TDAMN22DAHA6HAE TDAMN22DAHA6HRE TDAMN22DAGA6HNE A00 Jul-29-2011 Initial release TDBMN22DAHA1HCE TDBMN22DAHA1H6E TDAMN22DAHA6HNE TDBMN22DAHA1HNE TDB2N22DAHA1HNE TDB2N22EAHA1HNE A01 Dec-01-2011 Add new models TDBMN22EAHA1HNE TDBMN22EAHA6HNE TDCWN22MAHA1HNJ A02 Jan-07-2013 Add new models TDC2N22KAHE6HNJ 2
PAGE 3
Service Manual e2450Swd CONTENTS 1. Monitor Specifications ----------------------------------------------------------------------------------------- 4 1.1 Product Features --------------------------------------------------------------------------------------------- 4 1.2 Factory Preset Mode----------------------------------------------------------------------------------------- 5 2. Setup ----------------------------------------------------------------------------------------------------------------- 6 2.
PAGE 4
Service Manual 1. Monitor Specifications e2450Swd 1.1 Product Features Model number e2450Swd Driving system TFT Color LCD Viewable Image Size 59.8cm diagonal Pixel pitch 0.2715mm(H) x 0.2715mm(V) Video R, G, B Analog Interface & Digital Interface Separate Sync. H/V TTL Display Color 16.7M Colors Dot Clock 148.5MHz Horizontal scan range 30 kHz – 83 kHz Horizontal scan Size(Maximum) 521.28mm Vertical scan range 55 Hz - 75 Hz Vertical scan Size(Maximum) 293.
PAGE 5
Service Manual e2450Swd 1.2 Factory Preset Mode HORIZONTAL VERTICAL FREQUENCY(KHZ) FREQUENCY(KHZ) 640×480 @60Hz 31.469 59.940 VGA 640×480 @67Hz 35.000 66.667 VGA 640×480 @72Hz 37.861 72.809 VGA 640×480 @75Hz 37.500 75.000 Dos-mode 720×400 @70Hz 31.469 70.087 SVGA 800×600 @56Hz 35.156 56.250 SVGA 800×600 @60Hz 37.879 60.317 SVGA 800×600 @72Hz 48.077 72.188 SVGA 800×600 @75Hz 46.875 75.000 SVGA 832×624 @75Hz 49.725 74.551 XGA 1024×768 @60Hz 48.363 60.
PAGE 6
Service Manual 2. Setup e2450Swd 2.1 Contents in Box Note: Not all signal cables (HDMI cables) will be provided for all countries and regions. Please check with the local dealer or AOC branch office for confirmation.
PAGE 7
Service Manual e2450Swd 2.2 Setup Stand & Base Please setup or remove the base following the steps as below. Setup: Remove: 2.3 Adjusting Viewing Angle For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference. Hold the stand so you will not topple the monitor when you change the monitor's angle. You are able to adjust the monitor's angle from -4°to 17°.
PAGE 8
Service Manual e2450Swd Note: Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen 2.4 Connecting the Monitor Cable Connections In Back of Monitor and Computer: 1. Power 2. Analog (DB-15 VGA cable) 3. DVI To protect equipment, always turn off the PC and LCD monitor before connecting. 1. Connect the power cable to the AC port on the back of the monitor. 2.
PAGE 9
Service Manual e2450Swd 2.5 Wall Mounting Preparing to Install An Optional Wall Mounting Arm. This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this procedure. Follow these steps: 1. Remove the base. 2. Follow the manufacturer's instructions to assemble the wall mounting arm. 3. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the monitor. 4.
PAGE 10
Service Manual 3. Operation Instructions e2450Swd 3.1 Hotkeys Power Press the Power button to turn on/off the monitor. < Eco (DCR)/Press the Eco key continuously to select the Eco mode of brightness and DCR/I-Care on when there is no OSD. (Eco mode hot key may not be available in all models). 4:3 or Wide/+ When there is no OSD, press + continuously to change 4:3 or wide image ratio. (If the product screen size is 4:3 or input signal resolution is wide format, the hot key is disable to adjust.
PAGE 11
Service Manual e2450Swd 3.2 OSD Setting Basic and simple instruction on the control keys. 1) Press the MENU-button to activate the OSD window. 2) Press - or + to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate it. press - or + to navigate through the sub-menu functions. Once the desired function is highlighted, press MENU-button to activate it. 3) Press - or + to change the settings of the selected function. Press AUTO to exit.
PAGE 12
Service Manual e2450Swd Luminance 1. Press (Menu) to display menu. 2. Press or to select (Luminance), and press 3. Press or to select submenu, and press 4. Press or to adjust. 12 to enter. to enter.
PAGE 13
Service Manual 5. Press e2450Swd to exit.
PAGE 14
Service Manual e2450Swd Image Setup 1. Press (Menu) to display menu. 2. Press or to select (Image Setup), and press 3. Press or to select submenu, and press 4. Press or to adjust. 14 to enter. to enter.
PAGE 15
Service Manual 5. Press e2450Swd to exit. Color Setup 1. Press 2. Press (Menu) to display menu. or to select (Color Setup) , and press 15 to enter.
PAGE 16
Service Manual 3. Press or 4. Press or 5. Press e2450Swd to select submenu, and press to adjust. to exit. 16 to enter.
PAGE 17
Service Manual e2450Swd Picture Boost 1. Press (Menu) to display menu. 2. Press or to select (Picture Boost), and press 3. Press or to select submenu, and press 4. Press or to adjust. 17 to enter. to enter.
PAGE 18
Service Manual 5. Press e2450Swd to exit. OSD Setup 1. Press 2. Press (Menu) to display menu. or to select (OSD Setup), and press 18 to enter.
PAGE 19
Service Manual 3. Press or 4. Press or 5. Press e2450Swd to select submenu, and press to adjust. to exit. 19 to enter.
PAGE 20
Service Manual e2450Swd Extra 1. Press (Menu) to display menu. 2. Press or to select (Extra), and press 3. Press or to select submenu, and press 4. Press or to adjust. 20 to enter. to enter.
PAGE 21
Service Manual 5. Press e2450Swd to exit. Exit 1. Press (Menu) to display menu.
PAGE 22
Service Manual 2. Press or 3. Press e2450Swd to select (Exit), and press to exit. 3.3 LED Indicator status LED Color Full Power Mode Green or Blue Active-off Mode Orange or Red 22 to enter.
PAGE 23
Service Manual e2450Swd 4. Interface description 4.1 D-Sub 15pin Interface Pin No. Description Pin No. Description 1. Video-Red 9. +5V 2. Video-Green 10. Ground 3. Video-Blue 11. N.C. 4. N.C. 12. DDC-Serial data 5. Detect Cable 13. H Sync 6. GND-R 14. V Sync 7. GND-G 15. DDC-Serial clock 8. GND-B 4.2 DVI Interface Pin No. Description Pin No. Description 1. TMDS Data 2- 13. TMDS Data 3+ 2. TMDS Data 2+ 14. +5V Power 3. TMDS Data 2/4 Shied 15.
PAGE 24
Service Manual e2450Swd 4.3 LVDS pin assignment 4.4 Plug and Play Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The DDC2B is a bi-directional data channel based on the I2C protocol. The host can request EDID information over the DDC2B channel.
PAGE 25
Service Manual 5. Panel Feature e2450Swd LCM236HGE02A01130F(CMI： M236HGE-L20) is a 23.6‖ TFT Liquid Crystal Display module with WLED Backlight unit and 30Pins 2ch-LVDS interface. This module supports 1920 x 1080 Full HD mode and can display up to 16.7M colors. FEATURES - Contrast ratio 1000:1 - Response time 5ms. - Brightness 250nits(Typ.) - Color saturation NTSC 72%. - WXGA (1920 x 1080 pixels) resolution. - LVDS (Low Voltage Differential Signaling) interface. - RoHS compliance. 5.
PAGE 26
Service Manual e2450Swd 5.2 Absolute Maximum Ratings Absolute maximum ratings of the module are as follows: Value Item Symbol Min Typ Max Unit Note Power Supply Voltage Vcc -0.3 - +6 V (1) Logic Input Voltage Vin -0.3 - +3.
PAGE 27
Service Manual e2450Swd 5.3.2. BACKLIGHT UNIT (LED matrix is 16S4P) : Parameter guideline for LED driving is under stable conditions at 25℃ (Room Temperature ): 5.4 Panel Block Diagram 5.
PAGE 28
Service Manual e2450Swd (2) OPTICAL SPECIFICATIONS 28
PAGE 29
Service Manual 6. Block Diagram e2450Swd 6.1 LCD Block Diagram Monitor Block Diagram Panel LVDS DC-AC inverter Main Board AC-DC (5V/12V) Power Board Key board AC supply 90V-264V D- SUB PC- DVI /DDC /DDC Input signal 6.2 Main Board Block Diagram Main Board Block Diagram Crystal 14.318MHZ Panel Interface (X401) Audio Amplifiers FLASH MX25L2026D M1I-12G (U402) Scalar TSUMU58VHN-1 LQFP-80 (Include ADC, OSD, MCU) (U401) 5V 3.3V 1.
PAGE 30
Service Manual e2450Swd 6.
PAGE 31
Service Manual e2450Swd 6.
PAGE 32
Service Manual 7. Schematic e2450Swd 7.1 Main Board 715G4502M 04.SCALER 02.INPUT +5V EDID_WP R0+ R0SOG_DET +5V G0+ G0B0+ B0EDID_WP AHS0 AVS0 DDCSDA1 DDCSCL1 VGA_CABLE_DET R0+ R0SOG_DET G0+ G0B0+ B0AHS0 AVS0 DDCSDA1 DDCSCL1 VGA_CABLE_DET R0+ R0SOG_DET G0+ G0B0+ B0AHS0 AVS0 VCC3.3 DDCSDA1 DDCSCL1 PA[0..9] VCC1.8 +5V VCC3.3 VCC1.8 +5V PA[0..9] PA[0..9] VGA_CABLE_DET 02.D-SUB INPUT PB[0..9] PB[0..9] EDID_WP 05.PANEL INTERFACE PB[0..9] EDID_WP P_SCL P_SCL P_SDA P_SDA VLCD VLCD 05.
PAGE 33
e2450Swd DDCSCL1 R101 DDCSCL_A 100R 1/16W 5% VSIN0 5 DDCSCL1 14 13 DDCSDA1 R106 DDCSDA_A 100R 1/16W 5% 5 DDCSDA1 DET_VGA D-SUB 15P 10 5 9 4 8 3 7 2 6 1 15 HSIN0 CN101 12 11 R102 100R 1/16W 5% VGA_CABLE_DET VGA_CABLE_DET 5 VGA_5V VGA_5V BIN0BIN0 GIN0GIN0 RIN0RIN0 ZD101 RLZ5.
PAGE 34
26 25 GND GND 18 17 10 9 2 1 13 12 5 4 21 20 23 24 U104 I/O1 I/O4 GNDVDD I/O2 I/O3 NC Q101 6 5 4 ESD_DVI ESD_DVI ESD_DVI U105 R134 R135 R136 R137 R138 R139 10R 10R 10R 10R 10R 10R 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 5% 5% 5% 5% 5% 5% RX0+ RX0RX1+ RX1RX2+ RX2- 5 5 5 5 5 5 8 7 6 5 R140 R141 10R 1/16W 5% 10R 1/16W 5% VCC WP SCL SDA A0 A1 A2 GND 1 2 3 4 220N16V FM24C02A DDCSCL2 5 DDCSDA2 5 EDID_WP DCLK+ DCLK- ESD_DVI C116 C115 RLZ5.
PAGE 35
Service Manual e2450Swd VCC1.8 U401 NT68660FG FB401 and FB402 is NC==>3.3V use TO252 type U401 NT68660UFG FB402 is NC==>3.3V and 1.8V LDO use SOT-223 type VCC1.8 7 FB401 300OHM CVDD C401 4.7UF 10V C0805 C402 100N 16V 6 PB[0..9] PB[0..9] PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 PB8 PB9 C403 100N 16V R402 R403 LVB3P LVB3M LVBCKP LVBCKM LVB2P LVB2M LVB1P LVB1M LVB0P LVB0M 1 3 5 7 NC/2K2 1/16W 5% NC/2K2 1/16W 5% 2 4 6 8 VCC3.3 CN401 NC/8PIN R401 3.9K 1% R404 3.9K 1% R405 3.9K 1% VCC3.
PAGE 36
Service Manual PA[0..9] PB[0..9] 5 PB[0..
PAGE 37
Service Manual e2450Swd +5V +5V VCC3.3 C701 4 R702 4K7 1/16W 5% +5V 2 INPUT OUTPUT 4 FB701 0 OHM +-5% 1/8W 1 ADJ/GND + VCC3.3 5 100N 16V C704 3 3,4,5 +5V DIM ON/OFF AZ1117H-3.3TRG1 100uF16V C702 NC/CONN VCC3.3 U701 C703 100N 16V 6 5 4 3 2 1 100N 16V +5V 3,4,5 CN701 R703 9 8 7 6 5 4 3 2 1 100R 1/16W 5% Adj_BACKLIGHT 5 + C706 U702 VCC3.
PAGE 38
Service Manual e2450Swd 7.2 Power Board 715G4744P ! R929 100 OHM 1/4W 1 BD901 KBP208G C916 2N2 500V C928 2N2 500V F801 0R05 1/4W +14.
PAGE 39
Service Manual e2450Swd FB802 D801 L801 1 2 1 2 CN803 +14.5V 10 OHM 1/8W 47UH BEAD 8 7 6 5 Q801 C814 100N 50V APM8005KCTRG 1 2 C810 0.
PAGE 40
Service Manual e2450Swd LOUT+ LOUTROUT+ ROUT- + C602 C603 0.47uF 16V 0.47uF 16V VOL R603 10K 1/10W 5% SE C609 1uF 16V 200PF 50V C617 C604 100uF 25V 200PF 50V C618 R602 10K 1/10W 5% 200PF 50V C620 +5V1 200PF 50V C619 +5V1 C621 220pF 50V C622 220pF 50V NC/10K 1/10W 5% U601 R609 R604 CN601 4 Lin 5 3 2 Rin 1 8 7 6 5 4 3 2 1 7K5 1/10W 5% C601 0.47uF 16V C606 0.
PAGE 41
Service Manual 7.3 Key Board e2450Swd 715G4747K 1 3 LED001 UB 2 SUR CN001 1 2 3 4 5 6 LBADC1 LBADC2 DC_POWERON LED_1# LED_2# C001 C002 NC/0.1uF 50V NC/0.1uF 50V R001 2KOHM 1% 1/10W R002 0R01 1/10W R003 R004 2KOHM 1% 1/10W 1K 1/10W SW005 SW LBADC1 SW004 SW POWER MENU SW003 SW SW002 SW SW001 SW AUTO(2.0K) 1.118V UP LBADC2 UP SGND DOWN AUTO Wire Harness (0) 0V DOWN(2K) 1.118V MENU(1K) 0.
PAGE 42
Service Manual 8.
PAGE 43
Service Manual 9. Maintainability e2450Swd 9.1 Trouble Shooting Main Board---No Power No power Check flow chart For the no power Press power key and look if the picture is normal NG Please reinsert and make sure the AC 100-240V is normal? NG Reinsert or check the power section OK Check 5V-CN101, 3.3V-U103-2; 1.
PAGE 44
Service Manual e2450Swd No picture (LED orange) No picture heck flow chart for the no signal Check signal wire NG Replace signal wire OK Check U103 Vout=3.3V; U104-out=1.
PAGE 45
Service Manual e2450Swd Power Board--No Power 5V/12V Check flow chart For the no power Check CN901 100-240V NG Check AC supply OK Check rectified voltage-C905 NG Check FuseF901/ BD901 L902/BD901/C901/C902 OK Check voltage of IC901-8pin NG check component R905/R920 OK Check T901(1-3)out-Vcc NG Check D901/R910/C911 OK Check IC901-drive out NG Check/replace IC901 OK Check MOS-Q901pin(G/D) NG Check D910/R912/R915/Q901 Around component OK Check T901sub rectified out 5V/12V, Check rectified diode D9
PAGE 46
Service Manual e2450Swd No Backlight of panel Check flow chart for the Inverter No Backlight Check voltage of C804-16V NG Open C804 voltage-16V OK NG Return check Power Check ON/OFFsignal OK NG Check main board OK After Power off, check C804/C811/Q805/Q806 Check IC801—11pin=5V NG After Power off, check R802\C806\C809 OK Check IC801-3pin waveform? NG Check aroud C809\Q802 Replace IC801 OK Check IC801-pin6-8-9-10-PWM? NG replaceIC801 OK Check Q805, Q806-Gate/Drain NG OK Check ZD802/ZD803 R8
PAGE 47
Service Manual e2450Swd Key Board--OSD no working OSD is unstable or not Check flow chart working For the key board Is Key Pad Board connecting normally Connect Key Pad Board NG OK Is Button Switch normally Replace Button Switch NG OK Is Key Pad Board normally Replace Key Pad Board NG OK Check Main Board 9.2 Equipments and Tools Requirement 1. Multi-meter. 2. Oscilloscope. 3. Pattern Generator. 4. DDC Tool with and Compatible Computer. 5. Alignment Tool. 6. LCD Color Analyzer. 7.
PAGE 48
Service Manual e2450Swd 9.3 Factory mode adjustment After replacing the Main board and the Panel, Check if white-balance is within the specs, then re-writing DDC is necessary. Check for enter the Factory mode： Press button and hold, reinsert the Power cord, then, press MENU, the monitor will may enter Factory OSD Menu. Then Press . Factory OSD Menu will appear in the screen. By select this ―F‖ button to enter Factory OSD Menu.
PAGE 49
Service Manual e2450Swd 9.4 Writing DDC program step 1. Prepared the PC with Windows XP system, DDC recording device (12V) 2. Connect the DDC recording device and the PC through PC parallel port 3. setup―Port95nt‖ driver program to PC , 4. select relevant program and run it, below figure will appear 5, Press ―LoadFile‖, select EDID -model of product, and select input port; 6.
PAGE 50
Service Manual e2450Swd 50
PAGE 51
Service Manual 10. BOM List e2450Swd Note: The parts information listed below are for reference only, and are subject to change without notice. Please go to http://cs.tpv.com.cn/hello1.asp for the latest information. 10.1 TDC2N22KAHE6HNJ BOM Location Part No Description Remark 040G 581 26704 LABEL 1 040G 58162461A EPA LABEL 1 049G 51 1A ERADICATOR 052G 1210 A Tasma aluminiowa 1 052G 1211 B Conductive Tape 85mm *40mm *0.
PAGE 52
Service Manual e2450Swd A15G1597101401 MAINFRAME 1 A33G1181ABJ 2L0100 KNOB Function Button 1 A33G1182 1 1C0100 POWER LENS FOR 50TH 1 A34G2558AEDS2B0130 BEZEL 1 A34G2559ABJ0DK0130 REAR_COVER 1 AM1G1740 10125 SCREW 2 AM1G1740 12125 SCREW 2 CBPCCN2A1J4 CONVERSION G4502-M01-000-0040-4-120912 1 CN402 033G3802 6B Y L WAFER 1 CN701 033G3802 9B Y L CONN 2.0 9P 1 CN408 033G801930F CH JS FFC CONN 1.0mm 30P R/A 34mm 6.3mm 1 R707 061G152M47964E SY RST MOFR 4.
PAGE 53
Service Manual e2450Swd Q401 057G 417526 SMALLTRAN MMBT3906 -0.
PAGE 54
Service Manual e2450Swd R130 061G0402102 JT RST CHIP 1K 1/16W 5% TZAI YUAN 1 R488 061G0402102 JT RST CHIP 1K 1/16W 5% TZAI YUAN 1 R487 061G0402102 JT RST CHIP 1K 1/16W 5% TZAI YUAN 1 R424 061G0402102 JT RST CHIP 1K 1/16W 5% TZAI YUAN 1 R425 061G0402103 JT RST CHIP 10K 1/16W 5% TZAI YUAN 1 R714 061G0402103 JT RST CHIP 10K 1/16W 5% TZAI YUAN 1 R427 061G0402103 JT RST CHIP 10K 1/16W 5% TZAI YUAN 1 R429 061G0402103 JT RST CHIP 10K 1/16W 5% TZAI YUAN 1 R799 061G0402103 JT RST
PAGE 55
Service Manual e2450Swd R721 061G0402472 JT RST CHIP 4K7 1/16W 5% TZAI YUAN 1 R115 061G0402472 JT RST CHIP 4K7 1/16W 5% TZAI YUAN 1 C109 061G0402750 JT RST 0402 75R 5% 1/16W 1 C103 061G0402750 JT RST 0402 75R 5% 1/16W 1 C106 061G0402750 JT RST 0402 75R 5% 1/16W 1 R122 061G0603000 JT RST CHIP MAX 0R05 1/10W TZAI YUAN 1 R417 061G0603331 JT RST 0603 330R 5% 1/10W 1 R418 061G0603471 JT RST CHIPR 470OHM +-5% 1/10W TZAI YUAN 1 R726 061G0805000 JT RST 0805 0.
PAGE 56
Service Manual e2450Swd C712 065G040210412K F CAP 0402 100NF 10% 16V X7R 1 C417 065G040210412K F CAP 0402 100NF 10% 16V X7R 1 C402 065G040210412K F CAP 0402 100NF 10% 16V X7R 1 C425 065G040210412K F CAP 0402 100NF 10% 16V X7R 1 C701 065G040210412K F CAP 0402 100NF 10% 16V X7R 1 C113 065G040210412K F CAP 0402 100NF 10% 16V X7R 1 C117 065G040210412K F CAP 0402 100NF 10% 16V X7R 1 C414 065G0402105A5K Y NO-SUGGEST CAP 0402 1UF 10% 10V X5R 1 C182 065G040222031J Y CAP CHIP 0402
PAGE 57
Service Manual e2450Swd FB401 071G 56V301 TA CHIP BD 0805 300R/700mA FCM2012VF-301T07 1 ZD101 093G 39GA01 T RLZ5.6B 1 D401 093G 39GA01 T RLZ5.6B 1 ZD102 093G 39GA01 T RLZ5.6B 1 D402 093G 39GA01 T RLZ5.6B 1 D403 093G 39GA01 T RLZ5.6B 1 U102 356G0662056 TEST ONLY AT2042K6-5.0TRG1 SOT-23-6 1 U106 356G0662056 TEST ONLY AT2042K6-5.0TRG1 SOT-23-6 1 U103 356G0662056 TEST ONLY AT2042K6-5.0TRG1 SOT-23-6 1 U107 356G0662056 TEST ONLY AT2042K6-5.
PAGE 58
Service Manual e2450Swd SW005 077G603S AI CJ TACT SWITCH AI 2PIN SEALED 1 SW004 077G603S AI CJ TACT SWITCH AI 2PIN SEALED 1 SW003 077G603S AI CJ TACT SWITCH AI 2PIN SEALED 1 SW002 077G603S AI CJ TACT SWITCH AI 2PIN SEALED 1 SW001 077G603S AI CJ TACT SWITCH AI 2PIN SEALED 1 SW005 077G603S AI HC TACT SW 2P 5mm 200g TS-6613F-5D 1 SW004 077G603S AI HC TACT SW 2P 5mm 200g TS-6613F-5D 1 SW003 077G603S AI HC TACT SW 2P 5mm 200g TS-6613F-5D 1 SW002 077G603S AI HC TACT SW 2P 5mm 2
PAGE 59
Service Manual e2450Swd D901 093G 60335 DIODE SR515 5A/150V DO-201AD 1 D909 093G 60519 DIODE SR560-MK23 5A/60V DO-27 SECOS 1 D905 093G 60519 DIODE SR560-MK23 5A/60V DO-27 SECOS 1 D909 093G3006 1 1 31DQ06FC3 NIHON INTER 1 D905 093G3006 1 1 31DQ06FC3 NIHON INTER 1 CN902 095G 825 9D518 HARNESS 9P(SCN)-9P(PLUG) 120mm 1 CN902 095G 825 9X518 HARNESS 9P(SCN)-9P(PLUG) 120MM 1 0Q1G 340 8140 SCREW Q1-SELF TAPING SCREW :Q x8.0 2 CN804 311GW200A06ABF CONN 2.
PAGE 60
Service Manual e2450Swd R818 061G0805103 JT RST 0805 10K 5% 1/8W 1 R801 061G0805103 JT RST 0805 10K 5% 1/8W 1 R918 061G0805103 JT RST 0805 10K 5% 1/8W 1 R805 061G0805104 JF RST CHIPR 100KOHM +-5% 1/8W FENGHUA 1 R805 061G0805104 JT RST CHIPR 100KOHM +- 5% 1/8W TZAI YUAN 1 R808 061G0805109 JF RST CHIPR 1 OHM +- 5% 1/8W FENGHUA 1 R807 061G0805109 JF RST CHIPR 1 OHM +- 5% 1/8W FENGHUA 1 R808 061G0805109 JT RST CHIP 1R 1/8W 5% TZAI YUAN 1 R807 061G0805109 JT RST CHIP 1R 1/8W 5
PAGE 61
Service Manual e2450Swd R930 061G1206101 JF RST CHIPR 100 OHM +-5% 1/4W FENGHUA 1 R910 061G1206101 JF RST CHIPR 100 OHM +-5% 1/4W FENGHUA 1 R929 061G1206101 JF RST CHIPR 100 OHM +-5% 1/4W FENGHUA 1 R912 061G1206101 JF RST CHIPR 100 OHM +-5% 1/4W FENGHUA 1 R903 061G1206101 JF RST CHIPR 100 OHM +-5% 1/4W FENGHUA 1 R909 061G1206101 JF RST CHIPR 100 OHM +-5% 1/4W FENGHUA 1 R903 061G1206101 JT RST CHIPR 100 OHM +-5% 1/4W TZAI YUAN 1 R929 061G1206101 JT RST CHIPR 100 OHM +-5% 1/4W
PAGE 62
Service Manual e2450Swd C914 065G080510232K F CAP 0805 1000PF 10% 50V X7R 1 C803 065G080510232K F CAP 0805 1000PF 10% 50V X7R 1 C906 065G080510232K F CAP 0805 1000PF 10% 50V X7R 1 C815 065G080510232K F CAP 0805 1000PF 10% 50V X7R 1 C923 065G080510232K Y CAP CHIP 0805 1N 50V X7R +/-10% 1 C914 065G080510232K Y CAP CHIP 0805 1N 50V X7R +/-10% 1 C803 065G080510232K Y CAP CHIP 0805 1N 50V X7R +/-10% 1 C906 065G080510232K Y CAP CHIP 0805 1N 50V X7R +/-10% 1 C815 065G080510232K Y
PAGE 63
Service Manual e2450Swd C917 065G1206222B2K M Panasonic Assign 1206 2.2NF 10% 630V X7R 1 C916 065G1206222B2K M Panasonic Assign 1206 2.2NF 10% 630V X7R 1 C929 065G1206222B2K M Panasonic Assign 1206 2.
PAGE 64
Service Manual e2450Swd FB903 071G 55 29 FERRITE BEAD 1 FB902 071G 55 29 FERRITE BEAD 1 FB802 071G 55 29 FERRITE BEAD 1 FB801 071G 55 29 X BEAD 3.5X2.2X0.8 45R 25% 3BDR3522-453A 1 FB903 071G 55 29 X BEAD 3.5X2.2X0.8 45R 25% 3BDR3522-453A 1 FB802 071G 55 29 X BEAD 3.5X2.2X0.8 45R 25% 3BDR3522-453A 1 FB901 071G 55 29 X BEAD 3.5X2.2X0.8 45R 25% 3BDR3522-453A 1 FB902 071G 55 29 X BEAD 3.5X2.2X0.
PAGE 65
Service Manual e2450Swd J812 095G 90 23 JUMP WIRE - - 1 J809 095G 90 23 JUMP WIRE - - 1 J909 095G 90 23 JUMP WIRE - - 1 J811 095G 90 23 JUMP WIRE - - 1 J805 095G 90 23 JUMP WIRE - - 1 J802 095G 90 23 JUMP WIRE - - 1 J907 095G 90 23 JUMP WIRE - - 1 C801 367G215X3314AT EC 330UF 20% 25V 10*12 RF 1 C913 367G215X4707AT EC 47uF 20% 50V - 6.