9.5" LCD Monitor AOC E2060SWD Service Service Service Horizontal Frequency 30-83 KHz Table of Contents Description Page Description Page Table of Contents.......……..............................……........1 5.2.Power Board……………..……………...….......21 Revision List.…........................................…………........2 6.Schematic……………........................................22 Important Safety Notice.……............................……......3 6.1.Main Board………...........................................
Revision List Version Release Date Revision History A00 Dec.
Important Safety Notice Proper service and repair is important to the safe, reliable operation of all AOC Company Equipment. The service procedures recommended by AOC and described in this service manual are effective methods of performing service operations. Some of these service operations require the use of tools specially designed for the purpose. The special tools should be used when and as recommended.
1.
2. LCD Monitor Description The LCD monitor will contain a main board, an adapter board, a key board which house the flat panel control logic, brightness control logic and DDC. The power part will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips each voltage. Monitor Block Diagram LED Drive.
3. Operating Instructions 3.1 General Instructions This monitor only has one external control function button; press the Power/Auto Configuration button to turn the monitor on or off. If you need to adjust other functions, please visit the official AOC website (www.aoc.com)to download and install AOC’s exclusive i-Menu application software, and then perform related function adjustments to get the screen you require. • Connect the power cord properly. • Connect the signal cable onto the PC’s graphics card.
1 USB (Optional) 2 Power 3 / 4 DVI (Optional) 5 Analog (DB-15 VGA cable) 6 Line in (Optional) To protect equipment, always turn off the PC and LCD monitor before connecting. 1. Connect the power cable to the AC port on the back of the monitor. 2. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer's D-Sub port. 3.
3.3 OSD Setting Basic and simple instruction on the control keys. 1) Press the MENU-button to activate the OSD window. 2) Press < or > to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate it . press< or >to navigate through the sub-menu functions. Once the desired function is highlighted, press MENU-button to activate it. 3) Press< or >to change the settings of the selected function. Press AUTO to exit.
Luminance 1 Press (Menu) to display menu. 2 Press < or > to select (Luminance), and press 3 Press < or > to select submenu, and press to enter. to enter. 4 Press < or > to adjust. 5 Press to exit.
Image Setup 1 Press (Menu) to display menu. 2 Press < or > to select (Image Setup), and press 3 Press < or > to select submenu, and press to enter. to enter. 4 Press < or > to adjust. 5 Press to exit.
Color Setup 1 Press (Menu) to display menu. 2 Press < or > to select (Color Setup), and press 3 Press < or > to select submenu, and press to enter. to enter. 4 Press < or > to adjust. 5 Press to exit.
Picture Boost 1 Press (Menu) to display menu. 2 Press < or > to select (Picture Boost), and press 3 Press < or > to select submenu, and press to enter. to enter. 4 Press < or > to adjust. 5 Press to exit.
OSD Setup 1 Press (Menu) to display menu. 2 Press < or > to select (OSD Setup), and press 3 Press < or > to select submenu, and press to enter. to enter. 4 Press < or > to adjust. 5 Press to exit.
Extra 1 Press (Menu) to display menu. 2 Press < or > to select (Extra), and press 3 Press < or > to select submenu, and press to enter. to enter. 4 Press < or > to adjust. 5 Press to exit.
Exit 1 Press (Menu) to display menu. 2 Press < or > to select (Exit), and press 3 Press < or > to select submenu, and press to enter. to enter. 4 Press < or > to adjust. 5 Press to exit.
4. Input/Output Specification 4.
4.
4.3 Panel Specification 4.3.1 General Features M195FGE-L20 is a 19.5” TFT Liquid Crystal Display module with WLED Backlight unit and 30 pins 2ch-LVDS interface. This module supports 1600 x 900 HD+ mode and can display up to 16.7M colors. The converter module for Backlight is not built in. 4.3.2 Display Characteristics 4.3.3 Electrical Characteristics TFT LCD MODULE Vcc = 5.
Back Light Unit Ta = 25 ± 2.ºC 4.3.
5. Block Diagram 5.1 Main Board 715G5270M01000004I 04.SCALER 02.INPUT +5V EDID_WP +5V EDID_WP R0+ R0SOG_DET G0+ G0B0+ B0AHS0 AVS0 DDCSDA1 DDCSCL1 VGA_CABLE_DET R0+ R0SOG_DET G0+ G0- B0+ B0AHS0 AVS0 DDCSDA1 DDCSCL1 VGA_CABLE_DET R0+ R0SOG_DET G0+ G0B0+ B0AHS0 AVS0 VCC3.3 DDCSDA1 DDCSCL1 PA[0..9] VCC1.2 +5V VCC1.2 +5V 05.PANEL INTERFACE PA[0..9] PA[0..9] VGA_CABLE_DET 02.D-SUB INPUT PB[0..9] EDID_WP VCC3.3 EDID_WP PB[0..9] PB[0..9] JV_SCL JV_SCL JV_SDA JV_SDA VLCD VLCD 05.
5.
6. Schematic 6.1 Main Board 715G5270M01000004I R151 100R 1/16W 5% VGA_CABLE_DET 5 16 CN101 R103 0R05 1/10W C190 GIN0 VGA_5V 4,5,7 +5V RIN0 R117 EDID_WP DDCSCL1 DDCSDA1 4,5 EDID_WP R116 R115 C109 U102 8 7 6 5 VCC E0 WC E1 SCL E2 SDA VSS 220nF 16V ZD103 RLZ5.6B 1 2 3 4 RIN0- HSIN0R123 VSIN0 R121 1 2 3 I/O1 I/O4 GND NC I/O2 I/O3 6 5 4 AZC398-04S DDCSCL_A DET_VGA C116 0.1UF 16V 1 2 3 I/O1 I/O4 GND NC I/O2 I/O3 6 5 4 AZC398-04S GIN0 C117 0.
+5V DVI5V 1 2 3 NC/0.1UF 16V DAT0+ DAT0DAT1+ DAT1DAT2+ DAT2- 1 FB190 U104 I/O1 I/O4 GND NC I/O2 I/O3 2 1 4K7 1/16W 5% R133 3 R135 22K 1/16W 85% 7 6 5 2 300OHM C119 U105 1 2 3 4 VCC E0 WC E1 SCL E2 SDA VSS 220nF 16V C120 ZD102 C118 DDC_WP NC/0.1UF 16V RLZ5.6B EDID_WP 3,5 NC/0.1UF 16V AZC398-04S R137 R138 R139 R140 R141 R142 10R 10R 10R 10R 10R 10R 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 5% 5% 5% 5% 5% 5% RX0+ RX0RX1+ RX1RX2+ RX2- 5 5 5 5 5 5 RLZ5.
ADC33 VDDP VDDC VCC3.3 VDDP FB401 3 4 5 6 7 8 10 11 1 2 39 61 VDDP VDDP 41 63 VDDC VDDC VCTRL LVA3P LVA3M LVA2P LVA2M LVA1P LVA1M LVA0P LVA0M RX2P RX2N RX1P RX1N RX0P RX0N RXCKP RXCKN DDCD_DA/RS232_TX1 DDCD_CK/RS232_RX1 R416 0R 1/16W 5% R401 65 U402 1 2 3 4 C410 WP 10K 1/16W 5% 0.
PA[0..9] PB[0..9] 5 PB[0..
+5V VCC3.3 U701 +5V VCC3.3 5 4 + 1 R701 4K7 1/16W 5% ADJ(GND) VIN C702 100uF16V 4 3 3,4,5 +5V VCC3.3 LSP1117E33AG 2 VOUT C704 0.1UF 16V +5V 3,4,5 CN701 R702 9 8 7 6 5 4 3 2 1 100R 1/16W 5% Adj_BACKLIGHT 5 + C706 VCC3.3 C705 100uF16V 3 VIN ADJ(GND) 0.1UF 16V DIM ON/OFF U702 R703 R704 10K 1/16W 5% 1 10K 1/16W 5% 2 VOUT CONN Q701 C707 LMBT3904LT1G TO-252 R705 22K 1/16W 5% on_BACKLIGHT 5 NC/0.1UF 16V R708 NC/5.
6.2 Power Board 715G4452P02002001M 200V-2 R904 100 OHM 1/4W L903 R905 100 OHM 1/4W +15V C910 2.2NF 400V-1 C919 2.2NF 2 C900 1NF 250V R906 100 OHM 1/4W 3.5uH R918 250R + D903 SR510-22 1 1 BD901 R919 100K 2KBP08M-70 + ! 2 + 3 T901 POWER X'FMR 1 R921 100K C907 68uF 450V 600V-1 2 9 8 3 4 7 6 ZD901 MTZJ T-72 18B C912 680uF 25V 2 R916 470OHM +-5% 1/10W Q903 KTD1028 D905 SR510-22 1 2 C906 R922 100K - R920 4 100K D902 FR107 ! C911 R908 47 OHM 1/4W2.
D801A 1 2 100V-2 SR3100-MK18 FB803 FB802 L801 +15V 1 + R804 D801 NC 47UH C801 330UF25V 10 OHM 1/8W 21 C814 100N 50V 1 BEAD R823 NC 1 U801 9 10 11 12 13 14 15 16 R818 10K 1/4W DIM R806 C803 1N 50V C806 220N 50V R803 300K 1/8W R807 8 7 6 5 4 3 2 1 ISW R815 1M 1% 1/8W C811 NC C808 NC 10 OHM 1/8W VIN VREF STATUS LDR SSTCMP ISW PWM ENA ISEN1 RT ISEN2 OVP GND ISET ISEN3 ISEN4 C809 NC 8 R805 100K 1/8W FB801 BEAD R817 0.1~0.
6.3 Key Board SGND 1 2 3 4 5 6 LBADC1 LBADC2 DC_POWERON LED_1# LED_2# 2ZD007 SUB NC/MLVS0603M04 1 NC/MLVS0603M04 1 CN001 269-3UYSUBC/S530-A3-X6/T3 2 UY BLUE 1 3 2ZD006 LED001 715G5357K03000001M SGND R005 2KOHM 1/10W R003 100R 1/10W 5% R001 100R 1/10W 5% R002 1K 1/10W 5% R004 2KOHM 1/10W POWER 0.083V AUTO DOWN UP MENU SW005 2ZD005 0.673V POWER( 100 ohm ) SW NC/MLVS0603M04 1 MENU(1K) SW004 2ZD004 1.118V SW NC/MLVS0603M04 1 0.
7. PCB Layout 7.
7.
7.
8. Maintainability 8.1 Equipments and Tools Requirement 1. Voltmeter. 2. Oscilloscope. 3. Pattern Generator. 4. DDC Tool with an IBM Compatible Computer. 5. Alignment Tool. 6. LCD Color Analyzer. 7. Service Manual. 8. User Manual.
8.2 Trouble Shooting 1.
2.
3.
4.
9. White- Balance, Luminance Adjustment Approximately 30 minutes should be allowed for warm up before proceeding white balance adjustment. How to setting MEM channel you can reference to chroma 7120 user guide or simpl use “SC” key and “NEXT” Key to modify xyY value and use “ID” key to modify the TEXT description Following is the procedure to do white-balance adjust . 2. Setting the color temp. you want A. MEM.CHANNEL 3 Warm (6500K): Warm color temp. parameter is x = 313 ±20, y = 329 ±20 B. MEM.
A. Adjust Warm (6500K) color-temperature 1. Switch the chroma-7120 to RGB-Mode (with press “MODE” button) 2. Switch the MEM.channel to Channel 3 (with up or down arrow on chroma 7120) 3. The LCD-indicator on chroma 7120 will show x = 313 ±20, y = 329 ±20 4. Adjust the RED on factory window until chroma 7120 indicator reached the value R=100 5. Adjust the GREEN on factory window until chroma 7120 indicator reachedthe value G=100 6.
10.
11. BOM List Note: The parts information listed below are for reference only, and are subject to change without notice. Please go to http://cs.tpv.com.cn/hello1.asp for the latest information. T9CMUF7KBGACHNE Location HDCP-SMT Part No. Description 040G 58162435A MANUAL P/N LABEL 052G PAPER TAPE 2191 A 070GHDCP500HDC HDCP CODE E08902 089G 715GAAE01 SIGNAL CABLE E08903 089G1745HAA DVI CABLE 1.5M ECN403 089G179J30N 22 FFC CABLE 30P 150mm 1.
M05203 SMTCC-U402 Q52G100204500A00HB AL FOIL Q52G1801MNT162BFLT INSULATING SHEET H40G000261553A TCO'05 EPA LABEL 756GHCCB0BV0090001 MAIN BOARD-CBPCCUFA1H2 100GAMMA007W11 MCU ASSY-056G2233501 CN404 033G3802 6B Y L WAFER CN701 033G3802 9B Y L CONN 2.0 9P CN410 033G801930F CH JS FFC CONN 1.0mm 30P R/A 34mm 6.3mm CN101 088G 35315F XH D-SUB 15PIN VERTICAL CONN WITH SCREW CN102 088G 35424FXNH DVI CONN WITH SCREW 24P 093G CRYSTAL S-F-14.
C702 067G 3051013PB EC 105C 100uF M 16V 5*11mm JH CD263 R003 061G0603101 JT RST CHIP 100R 1/10W 5% TZAI YUAN R001 061G0603101 JT RST CHIP 100R 1/10W 5% TZAI YUAN R002 061G0603102 JT RST CHIP 1K 1/10W 5% TZAI YUAN R004 061G0603202 JT RST 0603 2K 5% 1/10W R005 061G0603202 JT RST 0603 2K 5% 1/10W ZD007 093G 64 59 SU ESD MLVS0603M04 0603 ZD006 093G 64 59 SU ESD MLVS0603M04 0603 ZD004 093G 64 59 SU ESD MLVS0603M04 0603 ZD005 093G 64 59 SU ESD MLVS0603M04 0603 ZD002 093G 64 59
R816 061G08054702FT RST CHIP 47K 1/8W 1% R811 061G08055101FT RST CHIP 5K1 1/8W 1% R927 061G0805622 JT RST CHIPR 6K2 +-5% 1/8W TZAI YUAN R904 061G1206101 JT RST CHIPR 100 OHM +-5% 1/4W TZAI YUAN R905 061G1206101 JT RST CHIPR 100 OHM +-5% 1/4W TZAI YUAN R906 061G1206101 JT RST CHIPR 100 OHM +-5% 1/4W TZAI YUAN R801 061G1206103 JF RST CHIPR 10KOHM +-5% 1/4W FENGHUA R818 061G1206103 JF RST CHIPR 10KOHM +-5% 1/4W FENGHUA R919 061G1206104 JT RST CHIPR 100KOHM +-5% 1/4W TZAI YUAN R922 0
C919 065G120622272K Y CER 1206 2N2 500V X7R 10% C911 065G120622272K Y CER 1206 2N2 500V X7R 10% ZD902 093G 39S 38 T PTZ 9.1B 709G4452 HS001 COMSUMPTIVE ASSY SW003 077G603S AI HJ TACT SWITCH AI 2PIN SEALED SW004 077G603S AI HJ TACT SWITCH AI 2PIN SEALED SW002 077G603S AI HJ TACT SWITCH AI 2PIN SEALED SW005 077G603S AI HJ TACT SWITCH AI 2PIN SEALED SW001 077G603S AI HJ TACT SWITCH AI 2PIN SEALED 715G5357K03000001M KEY PCB FR1 SS 117*10*1.
FB801 071G 55 29 FERRITE BEAD C903 365G306K6812WR CAP Y1 680PF 10% 250V Y5P J9015 095G JUMP WIRE - - C809A 067G 4154799LT EC 4.7UF 20% 100V 8*11.5 J9005 095G 90 23 JUMP WIRE - - FB804 071G 55 29 FERRITE BEAD R903 061G152M39852T J9011 095G 90 23 JUMP WIRE - - 006G 31500 EYELET 90 23 SY RST MOF 0.39R 5% 2W C912 367G215S6814AT EC 680UF 20% 25V - 12.5*16 RF C900 065G306M10233R CAP Y1 1NF 20% 250V Y5U F901 084G 56 FUSE 3.15A 250V MST 3.
R140 061G0402100 JF RST CHIPR 10 OHM +-5% 1/16W FENGHUA R144 061G0402100 JF RST CHIPR 10 OHM +-5% 1/16W FENGHUA R139 061G0402100 JF RST CHIPR 10 OHM +-5% 1/16W FENGHUA R142 061G0402100 JF RST CHIPR 10 OHM +-5% 1/16W FENGHUA R137 061G0402100 JF RST CHIPR 10 OHM +-5% 1/16W FENGHUA R141 061G0402100 JF RST CHIPR 10 OHM +-5% 1/16W FENGHUA R138 061G0402100 JF RST CHIPR 10 OHM +-5% 1/16W FENGHUA R105 061G0402100 JF RST CHIPR 10 OHM +-5% 1/16W FENGHUA R120 061G0402100 JF RST CHIPR 10 OHM +
R117 061G0402223 JY RST CHIPR 22KOHM +-5% 1/16W YAGEO R492 061G0402224 JY RST CHIPR 220KOHM +-5% 1/16W YAGEO R429 061G0402392 JY RST CHIPR 3.9KOHM 5% 1/16W YAGEO R427 061G0402392 JY RST CHIPR 3.9KOHM 5% 1/16W YAGEO R428 061G0402392 JY RST CHIPR 3.
C408 065G040210412K F CAP 0402 100NF 10% 16V X7R C720 065G040210412K F CAP 0402 100NF 10% 16V X7R C706 065G040210412K F CAP 0402 100NF 10% 16V X7R C407 065G040210412K F CAP 0402 100NF 10% 16V X7R C116 065G040210412K F CAP 0402 100NF 10% 16V X7R C402 065G040210412K F CAP 0402 100NF 10% 16V X7R C112 065G040222031J A CAP 0402 22PF J 50V NPO C113 065G040222031J A CAP 0402 22PF J 50V NPO C109 065G040222415K Y CAP CHIP 0402 220nF 16V X5R C715 065G040222415K Y CAP CHIP 0402 2
C424 093G 64S501 SU ESD MLVS0402M04 4V 402 C427 093G 64S501 SU ESD MLVS0402M04 4V 402 C425 093G 64S501 SU ESD MLVS0402M04 4V 402 U401 356G0562080B17 SCALER TSUMU59AHN-1 LQFP-80 709G52700HS001 COMSUMPTIVE ASSY 715G5270M01000004I MAIN PCB FR4 DS 80*72*1.