A17UX231 User's Manual LCD TV 41T17TV673 5A6275
USER’S MANUAL TABLE OF CONTENTS INSTALLATION -------------------------------------------------------------------- 1 For Your Safety ---------------------------------------------------------------1 IMPORTANT SAFETY INSTRUCTIONS ------------------------------------- 3 PREPARATION -------------------------------------------------------------------- 4 OPERATING INSTRUCTIONS ------------------------------------------------ 6 Use of the remote control -------------------------------------------------- 6 To use th
FOR YOUR SAFETY Before operating the TV please read this manual thoroughly. This manual should be retained for future reference. IMPORTANT SAFETY INSTRUCTIONS Read before operating equipment 1. 2. 3. 4. 5. 6. 7. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions. 8.
16. This product may contain lead or mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org 17. Damage Requiring Service – The appliance should be serviced by qualified service personnel when: A. The power supply cord or the plug has been damaged; or B. Objects have fallen, or liquid has been spilled into the appliance; or C.
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE Note to the CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. 22.
2. Insert the aerial plug firmly into the aerial socket at the back of the TV. 3. Remote control: Remove the cover of the battery compartment. Insert the 2 batteries supplied (Type AAA 1.5V). 4. Power: Insert the power cord in the wall socket having an AC power supply. 5. Turn the TV on: Press the power button at the topside of the TV to turn it on. If the TV is turned off, the front light will also turn off.
OPERATING INSTRUCTIONS USE OF THE REMOTE CONTROL MUTE POWER Temporarily interrupt the sound or restore it. Press to turn on/off the TV. The TV is never completely powered off unless it is physically unplugged. DISPLAY Press this button to Display Channel number on the right-top corner. 0~9/100 Digit buttons To select a TV channel. CH Press or ( or ) to brows through the TV channels,which are not erased. To view a blocked channel, use the digital buttons to access，the channel and enter your access code.
TO USE THE MENUS 1. 2. 3. 4. Press the MENU button to display each menu Use the cursor up/down to select a menu item. Use the cursor left/right to enter a submenu or enable/disable the function. Press the MENU button to exit the menu. MAIN MENU Press the MENU button into the main OSD (On Screen Display). Adjust item include PC SETUP、SOUND SETUP、OSD SETUP、TV SETUP and PICTURE SETUP. PC Setup 1. Contrast, Brightness, Phase, Clock, H-Position, V-Position and Color are the functions for. 2.
The “Reset To Default” is user-defined and is only used to reset the red, green, blue back to the default value. 4. Reset To Default is used to reset all settings to default value. Note: All the “Reset To Default” functions are the same except those in menus set by the user, which can reset all settings to default value in all menus. SOUND Setup 1. 2. 3. 4. Volume is adjusted from 0 to 100. Bass and Treble are adjusted from 0 to 100.
OSD Setup 1. 2. 3. 4. 5. 6. Set OSD language Adjust the horizontal position of the OSD. Adjust the vertical position of the OSD. Adjust the OSD time-out. OSD Background Adjustment Show the resolution, H/V frequency and input port of current input timing. Do not execute reset, return to main menu.
TV Setup 1. AIR/CATV for different TV input solution, RF and cable. 2. Auto searching is used for searching all TV program channels. After finishing search and exiting, the machine will save the program automatically, you can also press “menu” to break the searching, but only the searched programs are saved when the machine exits searching. 3. Add/Erase is for add or delete the current channel for memorizes. 4. Current Program is display the current channel number。 5.
Text Mode:TT1~TT4 Often used for channel guide, schedules, bulletin board information for Closed Caption programs, news, weather information or stock marker reports. Not all Closed Caption modes are necessarily being use by a TV channel during the transmission of a Closed Caption program. V-CHIP Setup Select V-Chip on OSD then enter 4 digits of pin number. Initial pin number is “0000”. If you enter an incorrect pin number “Error” message will be displayed. It is the parental control function (V-chip).
C.
D. CHANGE PIN Personal Identification Number is for change password to control the Vchip setup; it’s included three steps. ENTER PIN to enable this function, then ENTER NEW PIN to change a new one. After that COMFIRM NEW PIN. Picture Setup 1、 Contrast,Brightness and Saturation are adjusted from 0 to 100. 2、 Hue is adjusted from 0 to 100. 3、 Sharpness is adjusted from 0 to100. Hue is only adjusted in NTSC telecast system.
CONNECT PERIPHERAL EQUIPMENT FRONT PANEL CONTROL KNOBS Power Key : Press to turn on or off the TV. MENU Key : Press to show the OSD menu and exit OSD menu at the TV. Down / Up Key : Press to perform select function and channel. - / + Key :Press to confirm your function selection and adjustment. Source Key : Press to select your input source. There is a wide range of video and audio equipment that can be connected to your TV. The following connection diagrams show you how to connect them.
PREPARATION Remove the back plate at the back of the TV as shown on the illustration opposite. Lay the LCD TV with the screen down on a table, as it will be easier to connect your peripheral equipment. Please take precaution not to damage the screen.
VIDEO RECORDER How to connect 1. 2. Connect the supplied antenna cable to the RF IN port of your VCR. Connect another RF cable ① from the output RF of your VCR to the input of your TV. Better quality when playing from your VCR can be obtained if you also connect the Video, Audio LEFT AND right (only for stereo equipment) cables ⑤ to the VIDEO, AUDIO L and R inputs AV.
DVD PLAYER Connect the video output port of DVD player to the video input port of TV. Connect the left and right channels of DVD to the left and right channels of audio input of TV. If your DVD player is equipped with S-VHS video port: For better quality picture, please connect the S port to the S input port? of TV.
TIPS Care of the screen Do not rub or strike the screen with anything hard as this may scratch, mar, or damage the screen permanently. Unplug the screen before cleaning the screen. Dust the TV by wiping the screen and the cabinet with a soft, clean cloth. If the screen requires additional cleaning, use a clean, damp cloth. Do not use liquid cleaners or aerosol cleaners.
Product Specification Feature 17” screen XGA ( 1280 x 1024 ) Resolution Items LCD Panel TV Function Specification Screen Size 17” screen Aspect Ratio 4:3 Resolution 1280 x1024(XGA) Display Area (opening) 337.92 mmx270.336mm HxV Pixel Pitch 0.264mm x 0.264mm Display colors 16.
Signal Input PnP compatibility PC Input Input frequency Recommended Input Audio Analog: D-Sub 15 pin (detachable cable) DDC 2B Analog：FH:31.5KHz to 80KHz FV:56Hz to75Hz Analog: 1280 x 1024 (60Hz) AV (Share) Speaker (built-in): Two 2 watt speakers Audio Output Audio Output: L / R OSD language English / French / Spanish /Portuguese Headphone Mini-jack for stereo (3.
Before Calling Service Please make these simple checks before calling service. These tips may save you time and money since charges for receiver installation and adjustments of customer controls are not covered under your warranty. Symptoms Items to Check and Actions to follow “Ghost ” or double *This may be caused by obstruction to the image antenna due to high rise buildings or hills. Using a highly directional antenna may inprove the picture.
control is in the TV mode.
GLOSSARY Audio / Video Inputs Located on the rear and the front of the receiver these connectors (RCA phono type plug) are used for the input of audio and video signals. Designed for use with VCRs (or other accessories) in order to receive higher picture resolution and offer sound connection options. S-Video Input Allows direct connection of high-resolution video sources, such as a Super VHS videocassette recorder, Laser Disc player, etc. Provides improved picture resolution, sharpness, and clarity.
