AOC 7F AOC 7F 17 inch Color Monitor User’s Manual by Envision Peripherals, Inc. www.aocmonitor.com Before operating your monitor, please read this manual thoroughly.
For Your Safety AOC 7F FCC Statement Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
For Your Safety Precautions • The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. As a safety feature, this plug will only fit into a grounded power outlet. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the grounded plug. • Do not use the monitor near water, e.g.
For Your Safety General Notes General Features: • Do not install the monitor near heat sources such as radiators or air ducts. • 17" (43.2 cm) Color Monitor AOC 7F • Crisp, Clear Display for Windows • Do not place monitor in direct sunlight or in areas with excessive dust, mechanical vibration or shock. • Supports Resolutions up to 1280 x 1024 pixels @60Hz • EPA ENERGY STAR® • Save the original shipping carton and packing materials in case you need to ship your monitor.
Before You Operate the Monitor AOC 7F Installing & Removing the Base AOC 7F 5 v2_123102
Before You Operate the Monitor AOC 7F Connecting the Wires Using the Power Cord Supplied Caution: Make sure the power cord is the correct type that is required in your area. This monitor has a universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage areas (no user adjustment is required). 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws. 2. Connect the power cord into your monitor's power input socket.
Before You Operate the Monitor AOC 7F Connecting the Wires Using An Optional Power Cord (Not Supplied) Follow these steps: The power cord supplied with your monitor can only be connected to a grounded electrical wall socket or power strip. 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws.
Operating Instructions AOC 7F Front Panel Buttons Power: Press this button to put the monitor into Off mode. The power indicator will turn orange. Press and hold this button again to restore the monitor to normal operation mode. Shuttle Knob: Press this knob to open the OSD window or select a highlighted function. Rotate this knob to switch functions or adjust settings. Power Indicator: A green light indicates that the monitor is on. An orange light indicates that the monitor is in Off mode.
Operating Instructions AOC 7F Adjusting the OSD Settings 1. Press the Shuttle Knob to open the OSD window. 5. To save and exit, select the exit function or leave the monitor alone for 10 seconds. If you want to adjust any other function, repeat steps 2-4. 2. Rotate the Shuttle Knob until the desired function is highlighted. Note: When the OSD window is open, the input signal timing settings appear at the top. H: stands for horizontal frequency and V: stands for vertical frequency. 3.
Operating Instructions AOC 7F Plug & Play DDC1/2B Feature Windows INF Driver File This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The communication channel is defined in two levels, DDC1 and DDC2B. Most computers will automatically configure your monitor to work with your computer.
Technical Support (FAQ) Problem AOC 7F Possible Solution Power LED is not ON • Make sure the power cord is properly connected to a grounded power outlet and to the monitor. No Plug & Play • • • • Picture is fuzzy • Adjust the Contrast and Brightness settings. Picture bounces or a wave pattern is present in the picture • Move electrical devices away from the monitor. They may be causing electrical interference. Power LED is ON (green or orange light is ON) but there is no video or picture.
Appendix AOC 7F Specifications CRT Size Input 17.0" (43.2 cm) 11.4” (29 mm) neck 0.25mm(D), 0.21mm(H) dot pitch 90 degree deflection Viewable image size 16.0” (40.6 cm) diagonal Preset Display area 11.8” (300 mm) X 9.1” (230 mm) Dot Clock 110 MHz Maximum Resolution 1280 x 1024 pixels Plug & Play VESA DDC1/2B TM AOC 7F 12 Video Red, Green, Blue Analog Interface Separate Sync. H/V TTL H/V Sync.
Appendix AOC 7F Specifications (continued) Environmental Considerations Operating Temp: 32° to 104°F (0° to 40°C) ambient Operating Humidity: 10% to 85% relative, non-condensing Signal Cable Attached Mini D-sub 15 Male Optimal Viewing Mode: 1024 x 768 x 85 Hz AOC 7F 13 v2_123102
Appendix AOC 7F Factory Preset Timing Table Standard VGA VESA / 85 VESA / 60 AOC 7F Resolution (in pixels) Horizontal Frequency Vertical Frequency 720 × 400 31.5 KHz 70 Hz 640 × 480 31.5 KHz 60 Hz 640 × 480 43.3 KHz 85 Hz 800 × 600 53.7 KHz 85 Hz 1024 × 768 68.7 KHz 85 Hz 1280 × 1024 64.
Appendix AOC 7F Connector Pin Assignment Pin Number AOC 7F Description Pin Number Description 1 Red 9 NC 2 Green 10 Ground 3 Blue 11 Monitor Ground 4 Ground 12 DDC-Serial Data 5 Ground 13 H-Sync 6 R-Ground 14 V-Sync / *V-Clk 7 G-Ground 15 DDC-Serial Clock 8 B-Ground * For DDC 15 v2_123102
