INSTALLATION 2 05/30/2022 V1.
Order or Purchase # SKU or Model # Need help? For technical support call 305-614-4070 or visit us at www.ANZZI.
2.4”[62mm] 0.2”[5mm] B=5.3”[136mm]~6.9”[174mm] 11.2”[285mm] 14.1”[357mm] 2.3”[58mm] 8.3”[210mm] ≥14.6”[370mm] ≥20.5”[520mm] ≥14.6”[370mm] 19.7”[500mm] 10.7”[271mm] A=16.1”[410mm]~17.9”[454mm] 14.1”[357mm] 2”[52mm] 8.3”[210mm] 18.9”[480mm] ≥14.6”[370mm] ≥19.5”[490mm] ≥13.8”[350mm] B=5.3”[136mm]~6.9”[174mm] 2.4”[62mm] 0.2”[5mm] A=16.9”[430mm]~18.
Release Button Water Inlet(left) Toilet Lid Knob Toilet Seat T-Connector Hose Nozzle Supply Hose Toilet (not provided)
1.Toilet Seat 2.Template 3.Fix Components Screw (2) Adjusting Plate (2) 4.T-Connector Anchor (2) (Suitable for Top Mount) Nut (2) (Suitable for Bottom Mount) 5.Hose Base Plate (1) 6.Installation Guide /User Manual Washer Filter Note:There are two installation ways for this product. Use Anchor for the top mount installation and Nut for the bottom mount installation.
Please read and and follow the installation and operation instructions carefully to ensure the seat's long life and reliable operation. FAILURE TO DO SO COULD CAUSE PROPERTY DAMAGE AND SERIOUS INJURY. Please keep this manual for future reference. Installation Guideline 1.Water pressure range: 0.07-0.8MPa(10~116PSI). 2.Do not connect to a hot water supply. Providing water temperature above 104°F / 40°C will damage the product and void your warrnty. Installation Steps 1.Remove the old toilet seat. 2A-1.
Installation Steps 3. Slide the Toilet Seat across the Base Plate until you hear a click sound to make sure the Toilet Seat is secured. 4. Turn off the supply stop, then disconnect the supply hose from the water tank. If you are using a rigid supply line you will need to purchase a flexible supply hose to install the toilet seat. 5. Install T-Connector to the Inlet and Supply Hose as shown. Connect the other point of Supply Hose to the supply stop if you're replacing the rigid supply with a new hose.
Operation Instruction Back Wash Function Turn the knob forward from the vertical position as the figure shows. The nozzle extends. Continuing to turn the knob forward will increase the flow rate of the nozzle. Turn the knob backward to the vertical position to stop the cleaning and retract the nozzle. Low flow High flow Front Wash Function Turn the knob backward from the vertical position as the figure shows. The nozzle extends.
Cleaning and Maintenance 1.Clean the outside parts of the product. 2.Clean the nozzle Use a soft sponge or cloth with a non-abrasive cleaner to clean the product. Never use hydrogen chloride cleaner, diluent, benzene sandpaper, polishing agent, perfume, pesticide and other clenaing products. Gently pull out the nozzle and use a soft toothbrush to cleaner the nozzle. 3.Clean Filter and Flow Restrictor. 4.Remove the Toilet Seat.
Trouble Shooting Symptoms Water is too low during Front/Back wash No water comes out during Front/Back wash Water dropping from bowl when using the unit Probable Causes Recommended Action 1. Low water pressure of the unit During Front/Back wash, turn the knob to a higher setting 2. Low water pressure of water supply Raise the water supply pressure higher than 0.07 MPa (10 psi) 1. Water shut-off valve is turned off Turn on the water supply stop 2.
