ITEM: TL-MBSEL200WH TL-MBSRN201WH ® ANZZI SOFT CLOSE MANUAL BIDET SEAT INSTALL & OPERATION MANUAL V1.1 TL-MBSEL200WH TL-MBSRN201WH DON’T WAIT! REGISTER NOW! Register your product within 90 days to ensure your product is coverage. Mail in the completed registry card (Pg. 2) or register online at www.swcorp.com/register.
® PRODUCT REGISTRATION* IMPORTANT: YOUR WARRANTY WILL NOT BE RECOGNIZED UNLESS THIS CARD IS FULLY COMPLETED AND RETURNED OR ONLINE REGISTRATION IS COMPLETED. 1. Register online at www.swcorp.com/register. You will be asked to fill out the same information you would in the registration card. Registering online is fast, secure and ensures we receive your information. 2. Complete, cut-out and mail the registration card below.
TL-MBSEL200WH 2.3in ≥20.5in ≥14.6in 14.1in 14.6in 19.7 in 8.3in 2.4in 0.2in B：5.3 ～6.9 in 11.2in A=16.9～18.7in TL-MBSRN201WH 8.3in 2in 14.1in ≥19.5in ≥13.8in 18.9 in 14.6in 2.4in 0.2in B：5.3 ～6.9 in 10.7in A =16.1～17.9 in Have questions? Call us at 1-844-44-ANZZI or visit us at www.ANZZI.
Part Name General Product Drawing Left inflow Remove hipon Right inflow Toilet lid Water tank Knob Toilet seat Water supply pipe Nozzle (Lower body cleaning) Nozzle (Hip cleaning) Tee joint Angle valve Toilet base Water inlet hose 4 Have questions? Call us at 1-844-44-ANZZI or visit us at www.ANZZI.
Parts 1.Cover plate 2.Install the template 3.Fix parts Connecting bolt（2） Expansion bolt (2) or fixing plate (1) Adjusting piece (2) 4.Tee joint Nut (2) 5.Inlet hose 6.Installation Guide /User Manual Installation Guide /User Manual filter screen Note: There are two installation methods for this product. The expansion bolt is the configuration of the recommended installation method, and the hiperfly nut is the configuration of another installation method. Please choose in practice.
Installation Please read this manual carefully for correct installation. Installation considerations 1.Water pressure range: 0.07-0.8MPa(10～116PSI), please use according to the instructions. 2.The angle valve shall be close to the installation and disassembly position of this product. Installation steps Installation preparation 1.Insert the connecting bolt into the adjusting piece. Insert the connecting bolt into the hole of the adjusting piece in the direction shown in the figure. 2.
Installation steps Installation Method 1: (Recommended) 1.Remove the old cover plate. Loosen nuts linking the cover and remove the cover. 2.Install expansion bolts. Press the expansion bolts into the ceramic holes respectively as shown in the figure. Cover plate 3.Install the template. As shown in the figure, place the installation template on the ceramic. 4.Install the fixing plate and lock it.
Connecting water pipes 1. Close the angle valve and remove the water supply hose connected to the water tank. The tee joint is connected to the angle valve and ensures that the rubber sealing ring is installed therein. 2.Connect the water supply hose to the tee joint. Note: The throttle cover and throttle 0-RING in the throttle valve shall be removed in the following two cases. a.When the inflow pressure is less than or equal to 0.05 MPa dynamic pressure. (e. G., domestic water tower, etc.) b.
Operation Method Hip cleaning function Turn the knob from the vertical gear in the direction shown (clockwise). Low flow Hip cleaning tut mouth stretch out, spray water cleaning. The flow rate varies with the rotation of the knob. High flow Lower body cleaning function (for women) Turn the knob from the vertical gear in the direction shown (counterclockwise). Low flow The lower body cleaning nozzle extends out and sprays water for cleaning. The flow rate varies with the rotation of the knob.
Cleaning and Disassembly 1.Clean the external parts of the product. Use a smooth sponge or cloth with a neutral cleaner to clean the product. It is forbidden to use hydrogen chloride cleaner, diluent, benzene, sandpaper, polishing agent, perfume, pesticide and other cleaning products. Insecticides 2.Clean the nozzle. Gently pull out the nozzle and use a smooth cloth, sponge or toothbrush to remove the kitchen cleaner and wipe the nozzle. Diluent Sandpaper 3.Clean filter screen and throttle valve 4.
5 Maintenance 1.Knob replacement. 2.Nozzle replacement. 1、Turn the knob to the maximum position in the hip washing direction as shown in Figure A. 2、Pull out the old knob directly along the axis as shown in Figure B. 3、As shown in Figure C, pull out the new knob along the old knob and insert the rib into the corresponding control valve slot. After hearing the "click" sound, the installation is completed.
6 Problem Judgment and Product Specifications Problem Judgment and Troubleshooting Failure Reason Inadequate flushing water Hip washing or woman washing can't get out of water. When in use, the base leaks Solution 1.Low water pressure When washing, quickly turn the knob to the maximum gear of "washing" or "women washing" 2.Low water pressure If the water pressure is lower than the minimum water pressure of 0.
