ITEM: TL-AZEB101B TL-AZEB103B TL-AZEB105B ANZZI ELECTRIC BIDET SEAT INSTALL & OPERATION MANUAL V1.
EN byANZZI PRODUCT REGISTRATION* IMPORTANT: YOUR WARRANTY WILL NOT BE RECOGNIZED UNLESS THIS CARD IS FULIY COMPLETED AND RETURNED OR ONLINE REGISTRATION IS COMPLETED. To ensure that your warranty is registered and confirmed please do one of the following: 1. Register online at www.swcorp.com/register. You will be asked to fill out the same information you would in the registration card. Registering online is fast, secure and ensures we receive your information. 2.
PRODUCT SIZE CHART 5.1"(130mm) 15.8"(401mm) 19.9"(506mm) Thank you for choosing ENVO Electric Bidet Seat. Please read and understand this entire manual before attempting to install, assemble or operate this product.
TABLE OF CONTENTS S AFET Y P REC A UTIONS------------- PG.I COMPONENTS PG.3 ELEC TRI C BI DET S EAT INSTALLTIO N · · · · · · ····· · · · · · · ····· · · · · PG.4 GUILDINGS FO R FI RST U S E PG.8 O PERATION INSTRUCTION OF SIDE KEY PG.9 REMOTE CONTROL INSTRUCTIONS ········ ········ ························ PG.Io CLEANING&MA INTEANAN C E ···· ········ ··································· PG.13 LONG-TIME PERSERVATI ON PG.ls P RO DU CT P A R AMETER S PG.Is FUNCTION LIST · PG.
SAFETY PRECAUTIONS Please carefully read lhe safety precaulions before inslallalion. This is importanl and must be observed. LL DANGER Only connect lo a Ground-Faull Circuit-lnlerrupter(GFCI) protected grounded socket. Do not remove the ground pin or use a ground adapter. LL WARNING •Any modification to your ENVO Electric Bidet Seat will lead to warranty failure. If cables, plugs or other components need to be repaired or replaced, they need to be handled by qualified electricians.
NOTE
COMPONENTS •--fl+-- �Side� - Safety instructions ----ii'+--- Toilet lid �sassemble button Powerplug - � � Water Supply Hose Mounting bracket Adapters Rubber fixing sleeve & Screws == �� Gaskets Metal snap Remote control TOOLS AND MATERIALS Wrench Screwdriver PG.
ELECTRIC BIDET SEAT INSTALLTION STEP 1 I INSTALL THE MOUNTING PLATE Press and hold the disassembly button, pull down and take out the mounting plate. Disassemble the screws from the sleeves and insert the rubber fixing sleeves into the holes of the toilet's bowl. screws -----1► Mounting brackets The hook of the Mounting Plate is pointing forward Place the mounting plate onto the surface of bowl, following by the Mounting Brackets and Screws.
covered
STEP 2 I INSTALL THE WATER SUPPLY HOSE Slide the Electric Bidet Seat toward the mounting plate until you hear a "click" sound. Electric Bidet seat Water supply valve • Turn on the water supply valve. Check all connections at arrows for leaks.Retighten if necessary, but do not overtighten. PG.6 G)Close the water supply stop. Disconnect the water supply hose of the toilet and the supply stop; @For 3/8" compression outlet: Install compatible adapter with gasket to the outlet and secure it.
Select a smooth and even surface to ensure the control holder remains seated. Tear off the adhesive tape and press against wall. NOTE: Clean the surface prior to affixing the control holder. Apply pressure firmly and evenly. Allow 15 minutes for adhesive to cure.
Open water supply valve and check for any leaks. Make sure the plug is plugged into the socket and the light is on. Press the “Test” button: The plug light should be off. Press the “RESET” button: The light of the plug should be on. DO NOT USE IF “TEST & RESET” FAILS! CALL TECHNICAL SUPPORT FOR MORE ASSISTANCE. When the Electric Bidet Seat is powered ON, you will hear an audible beep. When the cover is lifted a small amount of water will flow to pre-wet the inner bowl.
This key will stop any currently running function. Press and hold for 3 seconds (when not sat on) to turn OFF the power. Press and hold for 3 seconds again to turn the power back ON. Press and hold for 3 seconds (while sitting) to start the dryer function. The air temperature can be preset by the Air Temp key on the remote control. While sitting, press this key to start the front wash. The runtime is 4 minutes. Press the key again to turn ON/OFF the reciprocating cleaning.
Press this key to stop any function currently active. Press and hold for 5 seconds (while NOT sitting) to turn power ON/OFF. While sitting, press this key to start the Rear Wash. The runtime is 4 minutes. When Rear Wash is active: Press this key again to turn reciprocating cleaning ON/OFF. Press the “Massage” key to turn Massage ON/OFF. Press the “Position /\ V” key to adjust the stream’s position. Press the “Water Temp” key to adjust the water temperature.
While sitting, press this key to start the “Dryer” function. The runtime is 4 minutes. When the dryer function is ON press the “Air Temp” key to adjust the air temperature. While sitting, press and hold for 2 seconds to start the “Child Wash” function. The runtime is 4 minutes. Low-level water pressure and temperature is locked to ensure a safe washing experience for the child. Press this key during rinsing to select between 3 levels of water pressure. Except for Child Wash.
Press this key to turn Energy Saving mode on. The indicator light on the side panel will turn ON. When ON, the Energy Saving mode will automatically turn OFF when the user sits on the seat. It will automatically turn ON 10 minutes after the user leaves the seat. Press and hold for 3 seconds to turn ON/OFF the Night Light. The light will remain on for 10 minutes then automatically turn OFF. Press this key to cycle between 4 different seat heating temperatures. Normal / Low / Medium/ High.
CLEANING&MAINTENANCE Precautions before maintenance: G) Make sure that the power is turned off. @ Do not allow water to enter the interior of the product during maintenance. ® Make sure that the detergent is scrubbed to avoid sticking between the body of the product and the gap of the toilet. Product surface maintenance Please wring out the soft cloth after the soaking and use it again. If the surface of the product is dirty, use a neutral detergent for the cleaning.
Clean the filter screen When the water pressure is too low to operate the toilet normally, please clean the filter screen by following steps. STEP l I Close the supply stop. STEP 2 I Remove the filter screen. Detach the Electric Bidet Seat from the mounting plate. Place the Electric Bidet Seat vertically. Remove the filter screen by a screwdriver. STEP 3 I Clean the filter screen. Note: Do not use any detergent. Clean with fresh water only.
LONG-TIME PERSERVATION \ G)Drain the water of the tank. � @'I @Disconnect the power. �I �-�i/__1_11 ®Remove the batteries from remote control. PRODUCT PARAMETERS / Product type Product model '--- Instant heating TL-AZEBlOlB TL-AZEB103B TL-AZEBlOSB Product Name Electric Bidet Seat Rated power 1080W Maximum power 1450W Rated voltage 110-120V~ Rated frequency 60Hz Range of inlet water pressure minimum necessary water pressure 0.07 MPa (when flowing), maximum water pressure 0.
FUNCTION LIST TL-AZEBlOlB TL-AZEB103B TL-AZEBIOSB () (-1 --, Deodorization Photocatalyst Cold and hot SPA Child Spray Bowl Pre-Rinsing Massaging Oscillating Spary Adjustable Position Heated Water Photosensitive night light Nieht lieht Energy saver Soft Closing lid Seat Pressure Sensor Dryer Heated Seat Self Cleaning Nozzle Front / Feminine Wash Rear Wash --- \�j CJ /� "\ '\_ ) C) "' / "\ \_) 1· \ \''-/' () {r,,\ -,_; ,-, (�) \__) () (-\ '\_ _,) (- 1 \_/ 1-1 \J (.) ()'\ 1 '\_ ) 1·
Failure to Work Make sure the outlet is powered. Make sure the plug is connected properly and making full contact. Rinsing and Washing functions not producing water Make sure the water supply isn’t cut off. Make sure the water supply valve is open. Make sure there are no kinks or bends in the supply hose. Weak Water Stream Check the plumbing’s water pressure. Check filter for dirt and debris. Make sure the nozzle isn’t blocked and free from dirt and debris.
Water Shuts-Off While Cleaning It’s normal for the cleaning functions to turn off after 4 minutes. Water is not Hot Make sure the Water Temperature is set to low or normal. Air Dryer is not Hot Make sure the Air Temperature is set to low or normal. Air Dryer Shuts Off It’s normal for the air dryer to turn off after 4 minutes. Seat is not Hot Make sure the seat heater isn’t set to low or OFF. Check to make sure if the seat isn’t in Energy Saving mode.
ENbyANZZI 7.06.07.
