A ANZZI ® Item: SD-AZFL06001 ** ANZZI GLASS SHOWER DOOR INSTALL & OPERATION MANUAL DON'T WAIT! REGISTER NOW! Register your product within 90 days to ensure your product is recognized as an official purchase and is eligible for warranty coverage. Mail in the completed registry card (Pg. 2) or register online at www.swcorp.com/register. V1 .
® ANZZI PRODUCT REGISTRATION* IMPORTANT: YOURWARRANTYW ILLNOT BE RECOGNIZEDUNLESSTHIS CARD IS FULLYCOMPLETEDAND RETURNEDOR ONLINEREGISTRNION IS COMPLETED. To ensure that your warranty is registered and confirmed please do one of the following: 1. Register online at www.swcorp.com/register. You will be asked to fill out the same information you would in the registration card. Registering online is fast, secure and ensures we receive your information. 2.
INSTALLATION GUIDE • Please check the product for transit damage, missing parts immediately. Damage reported later cannot be accepted. Please handle the product with care. Avoiding any impact on all sides and edges of the glass. • Consult your local plumbing codes prior to installation. • To reduce the risk of breakage, keep corner protectors on glass while installing.
INSTALLATION GUIDE &WARNING • Threshold must be level for proper installation. • The installation of this unit requires that you drill down into the threshold. Contact the manufacturer of the base, or threshold material with any questions regarding the drilling of holes into their product. Tools Required 1�, ii� • This product is heavy and may require two people to install. • Use cut-resistant, non-slip gloves to reduce the risk of personal injury and hold the glass frimly.
Left-hand door installation shown Right-hand door installation shown
DIMENSIONS 34"[864mm� 0 0 74"[1880mm] 0 4
PARTS [Ol]Plastic anchor X6 (Q) ll-■ @lli 1111\\11- [02]5crew STSX40mm[1-9/16"] C X6 [03]Vertical Rail Xl C [OS]Fixed Panel Xl 5 [06]Bottom Rail Xl C [04]Vertical Rail Seal Strip Xl C [07]Bottom Rail Seal Strip Xl
ASSEMBLY [QS] [01] Part [01] [02] [03] [04] [OS] [06] [07] Discription Qty. Wall Plug 6 Screw STSX40mm[l-9/16"] 6 1 Wall Jamb 1 Wall Jamb Seal 1 Fixed Panel Bottom Rail 1 1 Bottom Rail Seal [02] [03] _JQ_2] GLASS THICKNESS: 10mm / 3/8" NOTE: INSTALLATION MUST BE DONE BY A QUALIFIED, LICENSED PROFESSIONAL. &ATTENTION e To avoid personal injury or property damage, identify components and read all instructions before installing.
INSTALLATION STEPS Step 1 • This shower door must be installed into a stud. Minimum threshold space is required. IMPORTANT: Using a stud finder,ensure that the wall on both side of the enclosure has a stud in the location shown. A stud in this location must be identified to support the support bar in order to proceed with the installation. If you do not have a stud in this area shown, find a qualified person for advise. {Fig 1) 1. Place the Wall Jamb[03] to the intended position.
Step 3 1. Replace the Wall Jamb[03]. Tighten the screws by the allen key. Fig 3 Step 4 1. Position the Bottom Rail [06] on the floor, perpendicular to the Wall Jamb[03]. Both Wall Jamb[03] and Bottom Rail [06] have a 45 ° angle to ensure a perfect connection. Make sure their edges match. Measure the distance from each end of Bottom Rail [06] to the back wall to be sure the bottom rail is straight. They should be the same. 3 2.
Step 5 1. Remove the Bottom Rail [06] and drill hole into the floor where marked. Place Wall Plugs [01] inside the holes. 2.lf needed, a rubber mallet can be used to insert Wall Plugs[0l]. 3.To reduce risk of property damage, the use of metal hammers is not recommended. If needed, use drill to slightly enlarge the opening of the hole. IMPORTANT: Wall Plugs[0l] MUST be used. 3 Fig 5 Step 6 1. Replace the Bottom Rail [06]. Tighten the screws by the allen key.
Step 7 1. Clean the Fixed Panel[OS] with rubbing alcohol. Install the Wall Jamb Seal[04] to the Fixed Panel [OS]. The top end of the Wall Jamb Seal[04] should meet the top of the glass. The bottom end should leave a gap of 10mm from the bottom of the glass. 5 Fig 7 Step 8 1.
Step 9 1. Install the Fixed Panel[0S] into the Bottom Rail [06] by placing the corner of the bottom of the fixed panel inside the outside edge of the Bottom Rail [06]. Then install the rest of the Fixed Panel[0S] into the Bottom Rail [06]. 3 5 ATTENTION !The Tsunami Guard coated side of the glass panel should face into the shower while the uncoated side faces out of the shower.The Fixed Panel[S]has a sticker(s) indicating which side should face in and out. Fig 9 Step 10 1.
Step 11 1. Apply a good quality Silicone Sealant on the Wall Jamb[03] and Bottom Rail [06] along the bottom profile and wall profiles (Fig 11). 3 5 Fig 11 The sealant should be applied to the interior edge. '8\ - 24 hours .,,, / I I / \ --- .,,, Allow 24 hours for silicone to dry before use.
Care & Maintenance GLASS: To ensure long lasting life for your glass shower products: wipe them off after each use with a soft cloth. Rinse and wipe off the glass using either a soft cloth or a squeegee to prevent soap buildup and water spots (Hard water can etch the surface of the glass over time if left to dry). To prevent scratching the surface: never use abrasive cleaners or cleaning products that contain scouring agents. Never use bristle brushes or abrasive sponges that may scratch the surface.
ANZZI ®
