It em: FT-AZ132* * FREESTANDING BAHTUB WITH M ETAL FEET INSTALL & OPERATION M ANUAL V1.0 06/ 03/ 2022 DON’T WAIT! REGISTER NOW! Register your product within 30 days to ensure your bathtub is coverage. Mail in the completed registry card (Pg. 2) or register online at www.ANZZI.com/register.
PRODUCT REGISTRATION* IMPORTANT: YOUR WARRANTY WILL NOT BE RECOGNIZED UNLESS THIS CARD IS FULLY COMPLETED AND RETURNED OR ONLINE REGISTRATION IS COMPLETED. 1. Register online at www.ANZZI.com/register. You will be asked to fill out the same information you would in the registration card. Registering online is fast, secure and ensures we receive your information. 2. Complete, cut-out and mail the registration card below.
Have questions? Call us at or visit us at www.ANZZI.
SAVE THIS MANUAL! READ THESE INSTRUCTIONS COMPLETELY BEFORE INSTALLING THE PRODUCTS. FAILURE TO DO SO COULD RESULT IN AN IMPROPER INSTALLATION AND COULD VOID THE WARRANTY. RESPONSIBILITY OF THE INSTALLER! THE INSTALLER MUST INSPECT AND WATER TEST THE PRODUCT PRIOR TO INSTALLATION TO ENSURE THE UNIT IS FREE OF DEFECT OR DAMAGE. IN THE EVENT OF A PROBLEM, THE UNIT MUST NOT BE INSTALLED. IF THE CRATE OR THE PRODUCT HAS BEEN DAMAGED DURING SHIPPING, PLEASE CALL US IMMEDIATELY.
IM PORTANT A) A freest anding bat ht ub is not designed t o support w eight on it s rim. Therefore, do not sit or st and on t he bat ht ub's rim. B) Please ret ain t his manual aft er inst allat ion for fut ure reference and maint enance. C) This is a t w o-person job. RECEIVE YOUR TUB Unpack and check for damage. Unpack t he bat ht ub and inspect for damage or missing part s right aw ay. Do not w ait t o do t his. Damage report ed aft er inst allat ion w ill not be covered by w arrant y.
SPARE PARTS LIST TOOLS REQUIRED Sili kon ADJUSTABLE WRENCH 6 SILICONE GUN Have questions? Call us at LEVELER RULER SCREWDRIVER or visit us at www.ANZZI.
A) FEET INSTALLATION St ep 1 1. Lay a t ow el, blanket , or carboard over t he floor. 2. Lay t he bat ht ub on t he covering t o prot ect it from scrat ches. 3. Take off t he plast ic covers of screw s and unscrew nut s and w ashers from t he t ub (t hese are pre-assembled on t he t ub). 4. Follow t he diagram below and inst all t he crossbar ont o t he bot t om of your bat ht ub. Do not t ight en yet as adjust ment s may be necessary lat er. St ep 2 1. See Pict ure ①.
B) OVERFLOW PLATE INSTALLATION Not e: The t ub is pre-built w it h int ernal overflow . Inst allat ion st eps: 1. Insert t he met al bar [Part 1] int o t he overflow hole. See Figures 1 and 2. 2. Thread t he screw t hrough t he met al bar and t he overflow plat e behind it . Tight en t he screw . See Figures 3 and 4. 3. Inst all t he overflow cover ont o t he bar and lock it in. See Figures 5 and 6.
C) POP UP DRAIN & DRAIN HOSE INSTALLATION Drain Inst allat ion Not es: 1. Apply silicone around t he drain aft er performing a successful w at er t est t o ensure no leakage. 2. Do NOT over-t ight en t he drain as t his could damage t he t ub. Have questions? Call us at or visit us at www.ANZZI.
Inst all t he drain hose See figures 1 and 2. Next , place t he w at erproof rubber w asher over t he drain hose w it h t he flat side facing upw ards. Screw t he drain hose over t he drain and t ight en. 10 Have questions? Call us at or visit us at www.ANZZI.
D) POSITION THE TUB Before placing t he t ub, make sure t he ground is complet ely flat . Next , place t he t ub over t he int ended inst allat ion area. Last ly, insert t he drain t hrough t he drain hole in t he floor. See t he Figure below . * All bathtubs are 100% water tested at the factory and certified to be free of leaks. Transportation and mishandling may cause leaks. It is necessary to test the bathtub while there is access to all sides of the bathtub.
CLEANING AND M AINTENANCE 1. To preserve t he polished surface, aft er using your t ub, clean w it h soft clot h and w arm soapy w at er t o w ash aw ay any body oils or soap residue t hat forms a ring t ide mark. 2. Do not use pow ders, past es, crème cleaners, t hinners, w indow cleaning sprays or dry cleaning liquid, et c t o clean t he t ub. 3. For overflow plat e and pop up drain, w e do NOT recommend you use any household cleaners t o clean t he product .
