Qixiang Electron Science & Technology Co.,Ltd. www.anytone.net A2.
ARES II Instruction Manual
CONTENTS FUNCTIONS & FEATURES ..................................................................1 STANDARD ACCESSORIE ..................................................................2 OPTIONAL ACCESSORIE ....................................................................2 INSTALLATION .....................................................................................2 GETTING ACQUAINTED ......................................................................6 HOW TO USE YOUR RADIO .......................
FUNCTIONS & FEATURES ◆ PA/FM/AM/USB/LSB mode ◆ Weather Channel 150-170MHz programmable(Optional) ◆ CTCSS/DCS Code ◆ PWR, RX RSSI S-Meter ◆ PC programmable ◆ Echo Function ◆ SQ, ASQ Function ◆ RF Gain Adjustment ◆ Mike Gain Adjustment ◆ RF PWR Adjustment ◆ Programmable RB ◆ NB/ANL Function ◆ Offset Function ◆ Beep Voice Prompt ◆ +10KHz Function ◆ TOT Function ◆ HI-CUT Function ◆ Busy channel lock ◆ Monitor ◆ LED Brightness Adjustment ◆ SWR Protection ◆ Voltage Protection ◆ VOX Function ◆◆ RX◆noise◆reduction
STANDARD ACCESSORIES Microphone Radio DC Power Cable Screws for bracket Pads for bracket Mounting Bracket Adjusting screws Microphone Hanger Spare Fuses (10A,250V) Non-slip Mat Self-tapping Screws Pads OPTIONAL ACCESSORIE USB Programming Cable External Speaker INSTALLLATON Choose the most appropriate setting from a simple and practical point of view. Your radio should not interfere with the driver or crash the driver's knee or leg when rush brake. 1.
Microphone connection 1. Plug microphone connector into jack. 2. Pull on the screw for microphone connector. 1 1 3 23 5 4 TX PWR 7 9 1 +30dB 1 3 23 5 4 TX PWR 7 9 +30dB ANTENNA INSTALLATION Before using this radio, please install a high efficent and harmonious adjusted CB antenna, suitable antenna type and correct installation will bring excellent communication.
1. Connect positive red power cable with the + terminal of the battery. 2. Connect negative black power cable with the - terminal of the battery. 3. Connect the DC power cable to the transceiver's power supply connector. ▲ We suggest not use cigar lighter as it often bring down the voltage. ▲ Locate the power cable away from high temperature, moisture, portfire and cable insulator. ▲ Use a full power cable even it is longer than need, do not take off the fuse holder from the cable.
Install Microphone Hanger Choose a ideal location which will not interfere the driver. Using supplied self-tapping screws and pads(2 sets) to fix the hanger. Install External Speaker If use an external speaker, please choose 8ohm speaker with 3.50mm mono band (doulbe cable) plug. 1. Locate the external speaker in a suitable place. 2. Plug into the speaker jack.
GETTING ACQUAINTED Front Panel 1 1 1 3 23 5 2 4 5 7 8 17 16 18 +30dB 11 10 13 12 14 15 No.
Rear Panel 22 21 20 19 ANT. PA.SP. EXT.SP. - POWER + 23 No.
HOW TO USE YOUR RADIO OFF/ON Radio 1. Turn VOL clockwise to switch on the radio, the radio emit a beep. When the LED displays frequency or channel, the radio is on. 2. Turn VOL anti-clockwise to switch off the radio, the radio is OFF when hear Ka Ta from the switch. Volume Control When the radio is turned on, turn VOL clockwise will increase the volume, turn VOL anti-clockwise will reduce the volume. Note: Adjust the volume during communication to get suitable level.
SLIDE SWTICH No. Function Position Description NB/ANL ANL OFF Trun on NB and ANL function NB/ANL 1 NB/ANL ANL OFF Turn on ANL fucntion NB/ANL ANL Turn off NB/ANL fucntion OFF Turn off NRC fucntion 2 Turn on NRC fucntion NRC NRC level set: rr for RX noise reduction level tr for TX noise reduction level.
FUNCTION MENU 1. Press the [UP] key of the microphone to enter into the radio function menu. 2. Rotate the channel switch or press the [UP/DN] key of the microphone to select the menu function options. 3. Press the [PTT] key of the microphone to enter into the menu setting. 4. Rotate the channel switch to select the desired setting. 5. Turn off to save and exit the function settings. LCD Description Display No.
ERROR CODE When the RX/TX indicator light on yellow,LED displays code,means the radio meet problem. E1: Voltage too low E2: Voltage too high E3: WX function invalid E4: Current BAND invalid E5: TX SWR too high SPECIFICATIONS GENERAL Frequency Range 28.000-29.695MHz(Programmable) Frequency Band L band: A/B/C/D/E/F Channel 40channels(programmable)in each band Frequency Control Phase-Locked-Loop Synthesizer Frequency Tolerance ± 5.
TRANSMITTER Power Output AM:1-12W(adjustable) FM:1-40W(adjustable) USB/LSB:1-35W(adjustable) Drain 8A(with modulation) Modulation FM/AM/SSB Inter-modulation Distortion SSB Carrier Suppression SSB: 3rd order, more than -25dB; 5th order, more than -35dB 55dB Unwanted Sideband Frequency Response 50dB AM/FM: 450 to 2500Hz Output Impedance 50ohms, unbalanced RECEPTION Sensitivity Selectivity AM:1.0μV for 10 dB(S+N)/N at greater than 1/2watt of audio output. FM: 1.
