EMIV-DUAL User Manual Application Information 01-EMIVDUAL-1_X1 June 29, 2004 AnyDATA.NET Inc. Hanvit Bank B/D 6F Byulyang-dong Kwachon KOREA Tel) 82-2-504-3360 Fax) 82-2-504-3362 EMIV-DUAL V1.0 AnyDATA.
Interface Description EMIV-DUAL Reference Manual Application Information AnyDATA.NET Inc. Hanvit Bank B/D 6F Byulyang-dong Kwachon KOREA Copyright ⓒ 2001 AnyDATA.NET Inc.. All rights reserved. Printed in the Republic Of KOREA. All data and information contained in or disclosed by this document are confidential and proprietary information of AnyDATA.NET Inc., and all rights therein are expressly reserved.
Interface Description EMIV-DUAL Reference Manual Application Information Introduction The EMIV-DUAL is designed for the test and simulation of the CDMA wireless data communications. User can connect the EMIV-DUAL to your PC or Notebook and easily test the wireless communications. User can use this to develop your applications software even before user’s own hardware is ready. It also can be used as a debugging during user’s hardware test. Disclaimer and Limitation of Liability AnyDATA.NET Inc.
Interface Description EMIV-DUAL Reference Manual Application Information FCC RF Exposure Information Warning! Read this information before using this device. In August 1996 the Federal Communications Commission (FCC) of the United States with its action in Report and Order FCC 96-326 adopted an updated safety standard for human exposure to radio frequency electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S.
Interface Description EMIV-DUAL Reference Manual Application Information Contents 1 2 3 Introduction 1.1 Purpose 1.2 Organization 1.3 Revision History Overview 2.1 Application Description 2.2 Technical Specifications 2.2.1 General Specification 2.2.2 Receive Specification 2.2.3 Transmit Specification 2.2.4 gpsOne Receiver Specification 2.2.5 Standards 2.3 Interface Diagram 2.4 EMIV-DUAL General Features 2.5 Internal Modem Features PIN Description 3.
Interface Description 4 5 6 EMIV-DUAL Reference Manual Application Information Interface Descriptions 4.1 Overview 4.2 RS232 Interface (Standard) Electrical Specifications 5.1 Absolute Maximum Ratings 5.2 Recommended Operating Conditions 5.3 Power Consumption 5.4 Serial Interface Electrical Specifications Mechanical Dimension 6.1 EMIV-DUAL Outline 7 FCC Notice 8 Installation Example EMIV-DUAL V1.0 AnyDATA.
Interface Description EMIV-DUAL Reference Manual Application Information 1. Introduction 1.1 Purpose This Manual provides hardware interface and programming information for EMIV-DUAL CDMA Wireless Data Modem. 1.2 Organization The interface and operation section is organized into the following subsections: Section 2 – Introduces users to the EMIV-DUAL CDMA Wireless Data Modem basic features and general specifications.
Interface Description EMIV-DUAL Reference Manual Application Information 2. Overview 2.1 Application Descriptions The CDMA Wireless Data Modem is a complex consumer communications instrument that relies heavily on both digital signal and embedded processor technologies. The Wireless Data Modem manufactured by AnyDATA.NET supports Code-Division-Multiple-Access (CDMA). This operates in 800MHz CDMA and 1900MHz PCS spectrum.
Interface Description EMIV-DUAL Reference Manual Application Information 2.2 Technical Specifications 2.2.1 General Specifications PARAMETERS DESCRIPTIONS External Access Code-Division-Multiple-Access (CDMA) CDMA Protocol IS-95 A/B, IS-126, IS-637A, IS-707A, IS-2000 Data Rate 153.6Kbps Transmit/Receive Frequency Interval 45MHz for Cellular and 80MHz for PCS Band Width 1.
Interface Description EMIV-DUAL Reference Manual Application Information 2.2.2 Receive Specifications PARAMETERS DESCRIPTIONS Frequency Range 869.04 ~ 893.97 MHz for 800MHz CDMA and 1931.25 ~ 1988.75MHz for 1900MHz CDMA Sensitivity Below –104dBm Interference Single tone (-30dBm @900KHz): Below –101dBm for 800MHz Single tone (-30dBm @1250KHz): Below –101dBm for 1900MHz Rejection Spurious Wave Suppression Below –80dBc Input Dynamic Range -25dBm ~ -104dBm 2.2.
Interface Description EMIV-DUAL Reference Manual Application Information 2.2.5 Standards IS-95A/B/C : Protocol Between MS & BTS IS-96A : Voice Signal Coding IS-98A : Base MS Function IS-126 : Voice Loop-Back IS-637 : Short Message Service IS-707 : Data Service Built-in TCP/IP : AnyDATA proprietary software IS-657 : packet data EMIV-DUAL V1.0 AnyDATA.
Interface Description EMIV-DUAL Reference Manual Application Information 2.3 Interface Diagram Figure 2-1 Interface Block Diagram EMIV-DUAL V1.0 AnyDATA.
Interface Description EMIV-DUAL Reference Manual Application Information 2.4 EMIV-DUAL General Features Figure 2-2 EMIV-DUAL General Features 2.5 Internal Modem Features Figure 2-3 Internal Modem General Features (DTG2000-DUAL) EMIV-DUAL V1.0 AnyDATA.
Interface Description EMIV-DUAL Reference Manual Application Information 3. PIN Description 3.1 8-Pin Male Modular Jacks (RS232 Standard) Molex (85503) RS-232 (PC) Pin 1 RI Pin 2 GND Pin 3 DTR Pin 4 CTS Pin 5 TX Pin 6 RTS Pin 7 RX Pin 8 DCD Figure 3-1 Right Angle Modular Jacks Pin Description (85503,Molex 8P) 3.2 3-Pin Connector (Debugging) GND Figure 3-2 TXD RXD Debugging Connector (5268,Molex 3P) 3.3 DC Power Connector - + DC 12V Figure 3-3 EMIV-DUAL V1.
Interface Description EMIV-DUAL Reference Manual Application Information 4. Interface Descriptions 4.1 Overview This chapter covers information required to design the EMIV-DUAL into a subscriber unit application. In addition, the internal signals that are necessary for complete understanding of the UART interfaces are described below. 4.2 RS232 Interface (Standard) The Universal Asynchronous Receiver Transmitter (UART) communicates with serial data that conforms the RS-232 Interface protocol.
Interface Description EMIV-DUAL Reference Manual Application Information 5. Electrical Specifications 5.1 Absolute Maximum Ratings Operating the modem under conditions that exceed those listed in the Absolute Maximum. The Ratings table may result in damage to the modem. Absolute Maximum Ratings may be considered as limiting values, and are considered individually.
Interface Description EMIV-DUAL Reference Manual Application Information 6. Mechanical Dimensions 6.1 EMIV-DUAL Outline EMIV-DUAL V1.0 AnyDATA.
Interface Description EMIV-DUAL Reference Manual Application Information 7. FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15, Part22 and Part24 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Interface Description EMIV-DUAL Reference Manual Application Information 8. Installation Example EMIV-DUAL V1.0 AnyDATA.
