AnyDATA.NET Wireless Wi-Fi Router, AWR-501L (User Manual) V 1.6 2008.11.
AWR-501L (AWR Mobile Router) AnyDATA CDMA Module Series Reference Design Specification Copyright © 2008 AnyDATA Corp. All Rights Reserved. Any part of this document may not be distributed, communicated, reproduced or transmitted in any form or by any means, electronic or mechanical or otherwise, for any purpose, without the permission of AnyDATA Corp. This document can be subjected to revision without further notice. Contact Address AnyData.Net Inc.(Korea) DaeGo Bldg, 8 th.
AWR-501L (AWR Mobile Router) Contents 1. Introduction................................................................................................................................................4 1.1 Feature.................................................................................................................................................4 1.2 Front & Back view ................................................................................................................................5 2.
AWR-501L (AWR Mobile Router) 1. Introduction 1.1 Feature - The AWR-501L CDMA 1x EV-DO IP Router supports the WLAN 802.11 b/g standard providing constant 54Mbps data rates which are proven and secure technology. - The AWR-501L combines the advanced CDMA EV-DO technique with the mature WAP technique together to provide one completely feasible, secure high-performance wireless network infrastructure.
AWR-501L (AWR Mobile Router) 1.2 Front & Back view ⑤ ⑨⑩ ⑪ 1) Power LED: A red light indicates connection to the power supply. 2) CDMA LED: A red light indicates that connection on the 1x or EV-DO or Hybrid port. 3) Wi-Fi LED: A red light indicates that the connection on the WLAN interface is available. 4) LAN LEDs: A red light indicates a connection to an Ethernet-enabled computer (ports 1-4) This LED blinks during data transmission.
AWR-501L (AWR Mobile Router) Computers. 2.
AWR-501L (AWR Mobile Router) AnyTime AnyPlace AnyWireless Data Solutions™ 7/39
AWR-501L (AWR Mobile Router) 3. Using the Configuration Menu Admin Login Once properly configured, the AWR-501L will obtain and assign IP address information automatically. Configuration settings can be done through the AWR-501L Configuration Menu. You can access this interface by performing the steps listed below: 1. Open a web-browser. Type in the IP Address of the AWR-501L (http://192.168.2.1) AWR-501L, ensure you enter the correct IP Address now.
AWR-501L (AWR Mobile Router) Setup Wizard > CDMA Dial-Up Setting The Setup Wizard screen will appear. Refer to the AWR-501L Quick Installation Guide for more information regarding the Setup Wizard. User Name Select the User Name for your EVDO connection here.
AWR-501L (AWR Mobile Router) Setup Wizard > Wireless LAN Security ESSID Security WPA You may change network name by entering new name From Authentication Type, you may select one of the following. - Open System: Non-security Mode - Shared Key (WEP) - WPA In order to use Shared Key (WEP)’s functionality, you need to enter password required for Active Key. (Password must be either 5 or 13 ASCII code.
AWR-501L (AWR Mobile Router) Setup Wizard > Password Setting Current Password Enter the current password for your connection here Password Enter the new Password to change for your connection here. Re-type password Enter your new password again for confirmation Re-type password is case sensitive to Password.
AWR-501L (AWR Mobile Router) Advanced Setup > System > System Status System Status Antenna Level: Displays current Antennal level Data rate : Display current data transfer speed WAN IP Subnet Mask INTERNET : Displays IP address provided by Internet Service Provider (ISP) : Displays Subnet Mask for the IP address provided by Internet Service Provider (ISP) DNS : Displays address of primary Domain server Secondary DNS: Displays address of secondary Domain Server.
AWR-501L (AWR Mobile Router) Advanced Setup > System > Gateway Name Config Gatewayt Name Enter the Gateway Name for AWR-501L and click “APPLY” Gateway name must include “,”.
AWR-501L (AWR Mobile Router) Advanced Setup > System > Firmware Upgrade →Firmware Update 1) Download latest firmware from AnyDATA’s web site, and save it in hard drive. 2) Click Apply to configure IP Address and to browse firmware you have saved in your hard drive. If you click “Apply”, you may encounter internet explorer security warning message twice. In this case, you are required to click “Run” 3) Upon clicking RUN twice, you will have windows as below. →From the window, enter IP address and click .
AWR-501L (AWR Mobile Router) Advanced Setup > System > Client Information Client Information Displays client list that using this ROUTER and their information.
AWR-501L (AWR Mobile Router) Advanced Setup > System > Remote Admin It must be set disable by default because of security reason. Please use more complex password, if you would like to set “Enable” this feature. If it set “Enable”, It is possible to allow remote administration from internet. Remote Admin Please use more complex password, if you want to set “Enable” this feature. Remote Administration Port Number Set the port number to access remote administration from internet.
AWR-501L (AWR Mobile Router) Advanced Setup > System > Password Settings Current Password Enter the current password for your connection here Password Enter the new Password to change for your connection here. Re-type password Enter your new password again for confirmation Re-type password is case sensitive to Password. If you lost password or want default setting, do initialization to Factory default setting. The default ID and password are “admin” and “admin” respectively.
AWR-501L (AWR Mobile Router) Advanced Setup > System > Reset Reset You may reboot AWR-501L by clicking Yes If you want to change security and CDMA dial-up setting, you may use this reset feature.
AWR-501L (AWR Mobile Router) Advanced Setup > System > Factory default Factory default You may restore the AWR-501L back to factory default setting by clicking YES AnyTime AnyPlace AnyWireless Data Solutions™ 19/39
AWR-501L (AWR Mobile Router) Advanced Setup > CDMA > Dial Up Setting User Name Select the User Name(e.q. ufon1 or ufon2) for your EVDO connection here. Password Enter the Password for your EVDO connection here. Dial Number Enter the Internet Connect Dial Number.
AWR-501L (AWR Mobile Router) Advanced Setup > CDMA > Your DNS Domain Name Server(DNS) Address Displays the DNS address given to AWR-501L Secondary DNS Address Displays the Secondary DNS address given to AWR-501L AnyTime AnyPlace AnyWireless Data Solutions™ 21/39
AWR-501L (AWR Mobile Router) Advanced Setup > CDMA > Reconnect Settings On Demand Redial Select the “Enable” When the internet disconnect, if the user uses the internet, it will again Connected. Select the “Disable” When internet disconnect, it retry connection rightly.
AWR-501L (AWR Mobile Router) Advanced Setup > CDMA > Preferred Mode Preferred Mode Digital only: Connecting automatically during 1x and EVDO: Connecting to EVDO only AnyTime AnyPlace AnyWireless Data Solutions™ EVDO communication 23/39
AWR-501L (AWR Mobile Router) Advanced Setup > LAN > LAN Setting IP Address If you want to change IP address of AWR-501L, enter new IP address and click “Apply” Subnet Mask Displays Subnet Mask address of AWR-501L By default, 255.255.255.
AWR-501L (AWR Mobile Router) Advanced Setup > Wireless LAN > Wireless Setting Wlan Radio Check whether you want wireless AP to be enabled or not. Channel ID Select appropriate channel ID to be used in wireless network.
AWR-501L (AWR Mobile Router) Advanced Setup > Wireless LAN > Security Security From Authentication Type, you may select one of the following. - Open System: Non-security Mode - Shared Key (WEP) - WPA In order to use Shared Key (WEP)’s functionality, you need to enter password required for Active Key. (Password must be either 5 or 13 ASCII code.) Once you complete configuration, then you will see the message box saying “After System Reset, Your setting value will be applied”.
AWR-501L (AWR Mobile Router) Advanced Setup > Firewall > Firewall Setting Firewall Setting Select whether you want firewall to be enabled or disabled. One you select and click Apply, the change will be effective.
AWR-501L (AWR Mobile Router) Advanced Setup > Firewall > Client Filtering Enable Client Filter This will restrict connection to certain site or application. th Enter the 4 IP address of Client PC, connected to AWR-501L Enter the TCP/UDP port to block connection and check if you need them to be enabled. Put check mark on Enable Client Filter Ex> The screen below will be displayed when you block Client PC whose IP address ranged from 192.168.2.2 to 192.168.2.
AWR-501L (AWR Mobile Router) Advanced Setup > Firewall > MAC Control MAC Address Control List This is to block certain Client PC from connecting to internet. Enter the MAC Address of PC you want to block, and put check mark beside “Block Connect to Internet” and click “Add”. The MAC address will be added and set. Put check mark below MAC Address Control.
AWR-501L (AWR Mobile Router) Advanced Setup > NAT NAT Setting Select whether use NAT function or not. In Computer Networking, the process of Network Address Translation (NAT, also known as Network Masquerading, Native Address Translation or IP Masquerading) involves re-writing the source and/or destination addresses of IP packets as they pass through a Router or firewall.
AWR-501L (AWR Mobile Router) Advanced Setup > NAT > Virtual Server Virtual Server You Can configure the Wireless Router as a virtual server so that remote users accessing services such as the Web or FTP at your local site via public IP addresses can be automatically redirected to local servers configured with private IP address.
AWR-501L (AWR Mobile Router) Advanced Setup > NAT > Port Mapping For some applications, you need to assign a set or a range of ports to a specified local machine to route the packets. Wireless Router allows the user to configure the needed port mappings to suit such applications. Port Mapping When network user try to access LAN, user need to assign and mapping the port number of application protocol to network IP and relevant port number of LAN.
AWR-501L (AWR Mobile Router) Advanced Setup > NAT > DMZ DMZ (Demilitarized Zone) If you have a local client PC that cannot run an internet application properly from behind the NAT firewall, you can open the client up to unrestricted two-way internet access by defining a virtual DMZ Host. This enable PC that has IP or MAC address can operate as WEB, FTP, Telenet or mail server without separate port forwarding, which means all port is opened. 1. Enable : To enable or disable the DMZ setting of ROUTER.
AWR-501L (AWR Mobile Router) 4. RJ11 Interface for Voice Call AWR-501L can make Voice Call with RJ11 Interface. A wire phone and RJ11 Interface of AWR-501L both enable Voice Call as follow. 1. Connect the line of the wire phone to ‘Tel port’ on the backside of AWR-501L of the wire phone. 2. When the phone is in on-hook state (put down), turn AWR-501L on, leave the phone for 10 sec during the system boot. 3. Once the system boots up, you may hear Dial Tone when you answer the phone.
AWR-501L (AWR Mobile Router) AnyTime AnyPlace AnyWireless Data Solutions™ 35/39
AWR-501L (AWR Mobile Router) 5. Troubleshooting This section provides an overview of common issues, and possible solutions for the installation and operation of the AnyDATA AWR-501L. 1. Why am I not able to obtain a wireless connection. • An Ethernet connection is required to troubleshoot the AWR-501L. If you have enabled Encryption on the AWR-501L, you must also enable encryption on all wireless clients in order to establish a wireless connection.
AWR-501L (AWR Mobile Router) 1. Double-click on the Local Area Connection icon in the taskbar. 2. Select the Support tab. The IP Address will be displayed. 3. Why am I not able to access the Configuration Menu when I use my computer to configure the router? • Ensure that the IP Address is in the same range and subnet as the AWR-501L. The IP Address of the AWR-501L is 192.168.2.1. All the computers on the network must have a unique IP Address within the same range (e.g., 192.168.0.x).
AWR-501L (AWR Mobile Router) 6. Technical Specifications Standards • IEEE 802.11b/g • IEEE 802.3 • IEEE 802.3u Advanced Firewall Features • IP Filtering • Scheduling • NAT (Network Address Translation) • MAC Filtering Operating Temperature • 0ºC to 50ºC Humidity: • 70% maximum Wireless Frequency Range: • 2.412GHz to 2.484GHz LEDs: • Power • CDMA • Wi-Fi (Wireless Connection) • LAN Physical Dimensions: • L = 120mm • W = 155mm • H = 30.5 Wireless Transmit Power: RF Output Power 802.
AWR-501L (AWR Mobile Router) Warranty: • 24 months Wireless Data Rates with Automatic Fallback: 802.11g : 54, 48, 36, 24, 18, 12, 9, 6 Mbps WLAN Data Rate 802.11b : 11, 5.
