Owner`s manual

P/N 1010455 Rev. E 01/15 7
OPERATION
1. 1. Turn the power on and allow the
unit to preheat for approximately
20–30 minutes.
NOTE: Do NOT push any button during
warmup time. The ashing green
Ready Light indicates that the
unit is not warmed up. The green
Ready Light will become steady
when the unit is warmed up.
2. Pull out the Spatula or Drawer
Assembly and set the product to be
steamed onto the Spatula.
3. Push the Spatula or Drawer
Assembly fully into the steamer.
4. Single Shot: Press and release the
Operate
button, then wait 20 seconds for the
steam to penetrate the product.
Timed Cycle: Press the Start/Stop
button to begin the steaming cycle.
The display will count down to zero
and an audio signal will sound at the
end of the steaming cycle.
5. Remove steamed product.
Programming
CYC (Total Cycle Time) refers to the
total programmed steam time set for the
product.
SHO (Shot Interval Time) refers to the time
set between shots of steam during a com-
plete cycle.
H2O (Steam Shot Time) refers to the water
volume consumed during each water pump
activation.
The amount of steam produced by your
Miracle Steamer depends on the amount of
water sprayed onto the steam generator.
Flooding of the generator may occur if the
H2O setting is too high. To prevent ood-
ing, the Shot Interval Time (SHO) can be
increased to allow more time for generator
heat recovery. Adjustments should be made
to both values to determine the best set-
tings for your cooking needs.
To program the control, refer to Figure 6 and
follow the procedure below:
1. Turn the unit on. The unit displays
the factory programmed Total Cycle
Time in minutes and seconds (Figure
6, Item A).
2. Press and release to change
the control from OPERATION to
PROGRAM mode.
UP DOWN PRGM
START/STOP
POWER
READY
Figure 5. Operating Controls
READY LIGHT
POWER
SWITCH
OPERATE BUTTON
MESSAGE
DISPLAY
START/STOP
BUTTON
WARNING
To avoid injury, be careful when pulling
the Spatula or Drawer out from unit. Be
sure to allow steam to escape before put-
ting hands or face over the steamer.
3. To change the Total Cycle Time in
minutes, press ▲ or ▼ to change
the time (Figure 6, Item B).
4. Press and release again, and
press▲ or ▼ to change the Total
Cycle Time in seconds (Figure 6, Item
C).
5. To change the SHO factory settings,
make sure the control is in PROGRAM
mode, then press and hold both
▲ and ▼ simultaneously for 1-2
seconds and release. SHO will be
displayed (Figure 6, Item D).
6. Press and release and then press
▲ or ▼ to change the SHO in sec-
onds (Figure 6, Item E).
7. Press and release again and
press ▲ or ▼ to change the SHO in
minutes (Figure 6, Item F).
8. Press and release again and
“H2O” will be
displayed (Figure 6, Item G).
9. To change the H2O (Steam Shot
time), press and release the Program
button again to display the setting
(Figure 6, Item H). Use▲ or ▼ to
increase or decrease the time.
10. Press the Start/Stop or Operate but-
tons to store the changes, exit the
PROGRAM Mode, and initiate the
cooking cycle.
NOTE: 208V and 220/240V Miracle
Steamers are factory pro-
grammed for the following
recommended settings:
• Total Cycle Time (CYC) = 15 min.,
00 secs. (Range: 3 seconds to 99
minutes 59 seconds)
• Shot Interval Time (SHO) = 00
min., 20 secs. (Range: 3 seconds to
5 minutes 59 seconds)
• Steam Shot Time (H2O) = 0_70
(Range: 0_10 second to 2_50)
This converts approximately 3/4 oz. (25 mil-
liliters) of water to steam every 20 seconds
for a 15 minute cooking cycle.
NOTE: 120V Miracle Steamer is factory
programmed for the following
recommended settings:
• Total Cycle Time (CYC) = 2 min.,
00 secs. (Range: 3 seconds to 99
minutes 59 seconds)
• Shot Interval Time (SHO) = 00
min., 20 secs. (Range: 3 seconds to
5 minutes 59 seconds)
• Steam Shot Time (H2O) = 0_40
(Range: 0_10 seconds to 2_50)
NOTE: Units with MFG. No. 9100440 are
factory programmed for the fol-
lowing recommended settings:
• Total Cycle Time (CYC) = 0 min.,
08 secs. (Range: 3 seconds to 99
minutes 59 seconds)
• Shot Interval Time (SHO) = 00
min., 10 secs. (Range: 3 seconds to
5 minutes 59 seconds)
• Steam Shot Time (H2O) = 0_60
(Range: 0_10 seconds to 2_50)
NOTE: The Start/Stop or Operate but-
tons may be pressed at any time
during programming to store the
changes and exit the PROGRAM
Mode.
NOTE: If a change is not made within
5 seconds at any time during
the programming process, all
changes made up to that point
are stored in memory and the
control reverts to the OPERATION
Mode.