Specifications

MIRACLE STEAMER
10
P/N 1010881 06/04
MIRACLE STEAMER
11
P/N 1010881 06/04
OPERATION (continued)
WARNING
To avoid injury, use care when pulling spatula
or Drawer out from unit. Allow steam to escape
before putting hands or face over the steamer.
U
P
D
O
W
N
P
R
G
M
S
T
A
R
T
/
S
T
O
P
R
E
A
D
Y

The amount of steam produced by your Miracle
Steamer depends on the amount of water sprayed onto
the steam generator.
Flooding of the generator may occur if the SHOT set-
ting is set too high. To prevent this from occurring, the
Shot Interval Time (RATE) may be increased to allow
more time for generator heat recovery. Adjustments
should be made to both values to determine the opti-
mum settings for your cooking needs.
To program the control, refer to Figure 4 and use the
following procedure in sequence:
1. Turn the Rocker Switch (power On/Off) to ON.
The display will show the factory programmed
Total Cycle Time in minutes and seconds (Item A,
Figure 4).
2. Press and release the Program button to change
the control from OPERATION to PROGRAM
mode.
NOTE: CYC, RATE, and SHOT are only displayed
momentarily during the programming sequence
when the Program button is pressed.
NOTE: If no change is made within 10 seconds
at any time during the programming process,
all changes made up to that point are automati-
cally stored in memory and the control reverts to
OPERATION mode.
Figure 4. Control Programming Sequence
U
P
D
O
W
N
P
R
G
M
S
T
A
R
T
/
S
T
O
P
R
E
A
D
Y

U
P
D
O
W
N
P
R
G
M
S
T
A
R
T
/
S
T
O
P
R
E
A
D
Y
��
U
P
D
O
W
N
P
R
G
M
S
T
A
R
T
/
S
T
O
P
R
E
A
D
Y

U
P
D
O
W
N
P
R
G
M
S
T
A
R
T
/
S
T
O
P
R
E
A
D
Y
��
U
P
D
O
W
N
P
R
G
M
S
T
A
R
T
/
S
T
O
P
R
E
A
D
Y

U
P
D
O
W
N
P
R
G
M
S
T
A
R
T
/
S
T
O
P
R
E
A
D
Y
A. Total Cycle Time
E. RATE Time in Seconds F. RATE Time in Minutes
H. SHOT Setting
B. Total Cycle Minutes C. Total Cycle Seconds
D. RATE Cycle
3. To change the Total Cycle Time in minutes, use
the UP or DOWN arrow buttons to change the
time (Item B, Figure 4).
4. Press and release the Program button again, and
use the UP or DOWN arrow buttons to change the
Total Cycle Time in seconds (Item C, Figure 4).
5. To change the RATE factory settings, make sure
the control is in PROGRAM mode and displaying
CYC time, then press and hold the two arrow but-
tons simultaneously for 1-2 seconds. RATE will be
displayed (Item D, Figure 4).
6. While pressing the Program button, use the UP or
DOWN arrow buttons to change the RATE (Shot
Interval Time) in seconds (Item E, Figure 4).
7. Press and release the Program button again and
use the UP or DOWN arrow buttons to change the
RATE (Shot Interval Time) in minutes
(Item F, Figure 4).
8. Press and release the Program button again and
SHOT will be displayed. When the Program but-
ton is pressed again, the unit displays the shot
time in 0.01 second increments (Item H, Figure 4).
9. To change the SHOT (Steam Shot time), press
and release the Program button again to display
the setting (Item G, Figure 4). Use the UP or
DOWN arrow buttons to increase or decrease the
time.
U
P
D
O
W
N
P
R
G
M
S
T
A
R
T
/
S
T
O
P
R
E
A
D
Y

G. SHOT Cycle