MANUFACTURING NUMBERS: 9100429 MIRACLE STEAMER � L IS T ED �� AN Models MS-150 I T A T IO L IS N S T ED �� P/N 1010881 06/04 Owner ’s Manual
MIRACLE STEAMER TABLE OF CONTENTS Owner information .....................................................2 General......................................................................2 Warranty Information .................................................2 Service/Technical Assistance ....................................3 Important safety information.....................................3 Electrical Ratings.......................................................5 Specifications ..............................
MIRACLE STEAMER Service/Technical Assistance Refer to the service agency directory and fill in the information below: If you experience any problems with the installation or operation of your unit, contact your local Roundup Authorized Service Agency. They can be found in the service agency directory packaged with the equipment. Authorized Service Agency Name: Phone No.: Fill in the information below and have it handy when calling your authorized service agency for assistance.
MIRACLE STEAMER IMPORTANT SAFETY INFORMATION (continued) - In addition to the warnings and cautions in this manual, use the following guidelines for safe operation of the unit. • • Read all instructions before using equipment. • For your safety, the equipment is furnished with a properly grounded cord connector. Do not attempt to defeat the grounded connector. • Install or locate the equipment only for its intended use as described in this manual. Do not use corrosive chemicals in this equipment.
MIRACLE STEAMER SPECIFICATIONS Electrical Ratings Electrical Cord & Plug Configurations Model and Voltage Mfg. Number Watts Amps Hertz MS-150HC 9100429 3300 14.4 50/60 230 CAUTION All electrical connections must be in accordance with local electrical codes and any other applicable codes. Letter Code* Description C Commercial Cord H Harmonized Cord (H)C** CEE 7/7, 16 Amp., 250 VAC (Assembly Only).
MIRACLE STEAMER SPECIFICATIONS (continued) Dimensions MS-150 21-3/16” (53.8 cm) 17-11/32” (28.8 cm) 20-3/4” ��� (52.7 cm) 14” (35.5 cm) 8-13/32” (21.
MIRACLE STEAMER INSTALLATION Unpacking WABolt RNING 1. Remove unit and all packing materials from shipping carton. THIS APPLIANCE MUST BE EARTHED (GROUNDED) Spatula Guard 2. The unit should come with the items listed below: • Owner’s Manual • Authorized Service Agency Directory • Spatula Assembly ��� ��� ���� Handle NOTE: If any parts are missing or damaged, contact Antunes Technical Service IMMEDIATELY at 1-877-392-7854 or 1-630-784-1000.
MIRACLE STEAMER INSTALLATION (continued) Model MS-150 CAUTION Be sure to follow all safeguards and precautions in the Important Safety Instructions section of this manual. The MS-150 has a self-contained water tank. To fill the self-contained water tank: 1. Open the sliding tank cover on top of the unit (Figure 2). CAUTION All electrical connections must be in accordance with local electrical codes and any other applicable codes. NOTE: Make sure filter inside tank is installed properly. 2.
MIRACLE STEAMER OPERATION IMPORTANT: 220/240V Miracle Steamers are factory programmed for the following recommended settings: General When the Operate button (Figure 3) is pressed, power is supplied to the water pump. The pump operates and water sprays onto the heated Steam Generator. The water flashes immediately into live steam and shoots down onto the product. • Total Cycle Time (CYC) = 15 min., 00 secs. (Range: 1 seconds to 99 minutes 59 seconds) • Shot Interval Time (SHO) = 00 min., 20 secs.
MIRACLE STEAMER OPERATION (continued) 3. To change the Total Cycle Time in minutes, use the UP or DOWN arrow buttons to change the time (Item B, Figure 4). WARNING To avoid injury, use care when pulling spatula or Drawer out from unit. Allow steam to escape before putting hands or face over the steamer. 4. Press and release the Program button again, and use the UP or DOWN arrow buttons to change the Total Cycle Time in seconds (Item C, Figure 4).
MIRACLE STEAMER OPERATION (continued) 10. Press either the Start/Stop, Single Shot, or Operate buttons to store the changes, exit the PROGRAM Mode and initiate the cooking cycle. To verify or change the generator setpoint temperature, press and hold the UP and DOWN arrow buttons simultaneously for three seconds. Then, raise or lower the temperature by depressing the UP or DOWN arrow buttons. Release the buttons when the desired temperature is reached.
MIRACLE STEAMER MAINTENANCE Daily WARNING Turn the unit off, disconnect the power source and allow the unit to cool down before performing any service or maintenance on the unit. 1. Turn the Rocker Switch (power On/Off) to OFF. Unplug the power cord and allow the unit to cool down before proceeding. 2. Remove the Spatula, Liner, Drip Pan, Top Cover, and Steam Vent (Figure 9).
MIRACLE STEAMER MAINTENANCE (continued) steamer. This purges any remaining delimer residue from the generator surface. 4. With the unit cool, use a wire brush and/or scraper to loosen and remove the excessive calcium/ mineral deposits from the generator surface (Figure 8). Next, take a wire brush and clean out any build up that has accumulated in the 28 steam ports (26 vertical and 2 horizontal) of the generator (Figure 8).
MIRACLE STEAMER MAINTENANCE (continued) Top Cover Drawer Wingnut Generator Cover Diffuser Steam Vent Steam Ports (26 vertical and 2 horizontal) Steam Generator �� ���� �� Food Compartment �� Liner �� � MS-355 Shown Drip Pan Figure 9.
MIRACLE STEAMER MAINTENANCE (continued) Technical Theory of Operation The solenoid valve opens, or the water pump runs, and allows a shot of water (approximately 25ml or 3/4 oz.) to flow onto the generator surface for steaming. When the Rocker Switch (power On/Off) is ON, line voltage flows to the primary side of the step down transformer. The transformer’s secondary side supplies 12 and 24 VAC to the Control Board.
MIRACLE STEAMER TROUBLESHOOTING WARNING To avoid possible personal injury and/or damage to the unit, inspection, test and repair of electrical equipment should be performed by qualified service personnel. The unit should be unplugged when servicing, except when electrical tests are required. Problem Control Display is Blank (power On/ Off switch is On but indicator light is off). Possible Cause Corrective Action The power cord is not correctly plugged in.
MIRACLE STEAMER TROUBLESHOOTING (continued) Problem Unit heats but there is little or no steam produced and/or The product requires more steaming than usual. Possible Cause Corrective Action Filter Strainer is restricted. Check and clean the Filter Strainer as described in the Maintenance section of this manual. Unit is not being cleaned properly (daily/monthly). Clean unit daily and monthly as described in the Maintenance section of this manual.
MIRACLE STEAMER REPLACEMENT PARTS �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� � �� �� �� �� �� ��� � � �� �� �� � �� �� �� �� �� �� �� �� 18 P/N 1010881 06/04
MIRACLE STEAMER REPLACEMENT PARTS (continued) MS-150 Service Compartment �� �� � �� �� �� �� � �� �� �� �� �� �� �� �� �� �� �� �� � �� �� �� �� �� � �� �� �� �� �� �� �� �� �� �� � �� �� � �� �� ��� �� �� �� P/N 1010881 06/04 19 �� ��� �� ���
MIRACLE STEAMER REPLACEMENT PARTS (continued) MS-150 Item Part No.
MIRACLE STEAMER WIRING DIAGRAMS ����� ���� ��� ������� ��� ��� ���� ����� ��� ��� ����� ����� ��� � � � � � ���� � � ��� ��� ��� ��� �� ��� � � � ��� �� ���� �� �� ��� 21 � � � � � ��� ������� ����� �� �� ��� �� ��� ��� �� ��� ��� ��� P/N 1010881 06/04 ����� ����� ����� ��� ��� ���� ������ ������� ��� ����� ���� �� ��� �������� �� ���� � ��� ��� �� �� �� � ���� � �� ��� � �� �������� ���� � ����������� ��� � ����� ������ � ��� ��� ��� ��
MIRACLE STEAMER NOTES 22 P/N 1010881 06/04
MIRACLE STEAMER NOTES P/N 1010881 06/04 23
LIMITED WARRANTY Equipment manufactured by Roundup Food Equipment Division of A.J. Antunes & Co. has been constructed of the finest materials available and manufactured to high quality standards. These units are warranted to be free from mechanical and electrical defects for a period of one year from date of purchase or 18 months from shipment from factory, whichever occurs first, under normal use and service, and when installed in accordance with manufacturer’s recommendations.