Datasheet

INPUTS
P2 . . . . . . . . . . . . . . . . . . . 2 Single-Ended, 2 Balanced, 1 Relay Trigger (3.5 mm Mono Jack)
P5 . . . . . . . . . . . . . . . . . . . 5 Single-Ended, 5 Balanced, 1 Relay Trigger (3.5 mm Mono Jack)
OUTPUTS
P2 . . . . . . . . . . . . . . . . . 2 Pairs Speaker Binding Posts, 1 Relay Trigger (3.5 mm Mono Jack)
P5 . . . . . . . . . . . . . . . . . 5 Pairs Speaker Binding Posts, 1 Relay Trigger (3.5 mm Mono Jack)
SWITCHES
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power (On/Off)
Rear Panel . . . . . . . . . . . . On/Off Modes (Trigger, Manual, Auto), Inputs (RCA, XLR, XLR -6dB)
THD+N . . . . . . . . . . . . . . . . . . . . . . . . . 0.0007% at 1 kHz, 0.008% at 20 kHz (200 W into 8 Ω)
POWER OUTPUT
(Per channel, continuous RMS, 20 Hz to 20 kHz, <0.1% THD, one or all channels driven)
Impedance 8 Ω 4 Ω 2 Ω
# of Channels Driven 1 All 1 All 1 All
P2 325 W 325 W 500 W 500 W 675 W 675 W
P5 325 W 325 W 500 W 500 W 675 W 675 W
P2 and P5 amplifiers are stable into any impedance down to a short circuit at full output
IMD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.00019% (CCIF, 325 W into 8 Ω)
POWER BANDWIDTH . . . . . . . . . . . . . . . . . . . . . . 10 Hz to 150 kHz (+0 -3 dB, 325 W into 8 Ω)
FREQUENCY RESPONSE . . . . . . . . . . 20 Hz to 20 kHz (+0 -0.15 dB), 5 Hz to 100 kHz (+0 -2 dB)
INPUT SENSITIVITY (RCA and XLR 0 dB inputs) . . 1 Vrms in for 28.3 Vrms out (100 W into 8 Ω)
INPUT IMPEDANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 kΩ (RCA), 22 kΩ (XLR)
DAMPING FACTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >600 at 20 Hz, 400 at 1 kHz (ref. 8 Ω)
S/N RATIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 dB, A-weighted (ref. 325 W)
CROSSTALK (between any two channels) . . . . . . . . . . . . . . . . -140 dB (20 Hz), -80 dB (20 kHz)
VOLTAGE GAIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 dB
SLEW RATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 V/µs
POWER REQUIREMENT
Power Consumption (at maximum power) (output 8 Ω load)
P2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1800 W (140W at idle)
P5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 x 1800 W (340W at idle)
DIMENSIONS
Height . . . . . . . 9-3/8 inches (23.8 cm) including feet; rack-mounting: 5 rack units without feet
Width: Standard version . . . . . . . . . . . . . . . . . . . . . . . . . . 19-1/4 inches (49 cm)
Rack-Mount version . . . . . . . . . . . . . . . . . . . . . . . . . 19 inches (48.3 cm)
No-Handle version . . . . . . . . . . . . . . . . . . . . . . . 17-1/4 inches (43.8 cm)
Depth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-1/2 inches (57.2 cm) including handles
WEIGHT (unpacked)
P2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 lb (34 kg)
P5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 lb (59 kg)
ADVANCED LOAD MONITORING (ALM)
All Anthem
®
Statement amplifiers are designed to perform flawlessly—offering stunning musicality,
tonal neutrality and incredible dynamics while driving any speaker load reliably under real-world
conditions! The power supply is conservatively rated and the amplifiers run cool for greater
reliability, but we didn’t stop there.
These amplifiers feature our ALM (Advanced Load Monitoring) circuitry which protects
sensitive output devices by constantly monitoring temperature, current and voltage to ensure
optimum long-term performance. ALM is totally non-invasive—it is not in the signal path
and only engages in the most extreme circumstances to protect the amplifier from damage
by maintaining the safe operating area of the output devices. Buyer beware however! Not all
amplifier manufacturers have sophisticated load-monitoring provisions. Many have saved the
added cost, leaving their output devices unprotected, choosing instead to use the amplifier’s
output devices as “fuses.” At Anthem, ALM is just one of the ways in which our products
provide owners with years of reliable service.
P2 | P5
TECHNICAL SPECIFICATIONS
P2
P5