USER’S MANUAL TITAN550
The high quality of our products is assured by a continuous process of refinement of their technical features. Therefore, it is possible that your product may differ in some respect from the descriptions contained in this manual. This is not a problem – it is an improvement. All features, descriptions, and illustrations contained herein are valid as of the date of publication. Disclaimer This manual is intended only as a guide for Antec’s Computer Enclosures.
5. 6. To remove the front bezel. There are three plastic tabs on the left side of the bezel. Release them from the top down to detach the bezel from the metal chassis. Swing the bezel open to about 90º angle and gently lift it upward. The front bezel will come off easily. Set it in a safe place. Note: In case you need to remove the double hinge door, open the door to 90º, and gently press the small plastic tab on the upper hinge.
The power supply is also equipped with a 3-pin fan signal connector. Connect it to one of the fan connectors on your motherboard. You may monitor the speed of the rear power supply fan through your motherboard BIOS or through the monitoring software that’s supplied with your motherboard. Note: At low temperatures, the fan may run as slow as 950 RPM. At these speeds, some motherboards may not properly detect the fan speed and may generate false warnings of fan failure.
CONNECTING THE AUDIO PORTS There is an Intel standard 10-pin connector (with also 7 individual wires with connectors) coming out from the front panel speaker and microphone connection. If your motherboard supports Intel’s standard onboard audio connector, you can plug in the 10-pin connector directly onto the board. For non-Intel standard audio connection, you need to plug the 7 individual connectors into the motherboard. Locate the internal audio connectors from your motherboard or sound card.
To install a floppy or other external 3.5" device to the 5.25" to 3.5" Adapter: 1. 2. 3. Slide the adapter out. Place the drive in the adapter and fasten it with the screws provided. Find a 4-pin floppy power connector on the power supply and connect it to the male 4-pin connector on the devices. COOLING SYSTEM The case has one 120mm Tricool fan installed in the rear. Two optional 92mm fan mounts may be found right behind the front bezel.
TITAN550 – TECHNICAL DIAGRAMS No. 1 2 3 4 5 6 7 8 9 10 11 Description Left Side Panel Expansion Slot Cover Top Panel 5.25" EMI Shielding HDD Drive Rail 5.25" to 3.5" Adapter (Sheet Metal) I/O Port PCB Assembly Right Side Panel Front Bezel 5.25" Drive Bay Cover 5.25" to 3.5" Adapter Cover No. 12 13 14 15 16 17 18 19 20 21 22 Description 3.5" Drive Bay Cover Front Bezel Mounting Bracket Front Door Hinge 3.
TITAN550 - DIAGRAMMES TECHNIQUES No. 1 2 3 4 5 6 7 8 9 10 11 Description Panneau gauche Couvercle de logements d'extension Panneau supérieur Blindage EMI 5,25 pouces Rail de lecteur HDD Adaptateur 5,25/3,5 pouces (tôle) Carte de circuits imprimés à port E/S Panneau droit Collerette d'encastrement avant Couvercle de baie d'unité de 5.25 pouces Couvercle de l'adaptateur 5,25/3,5 pouces No.
TITAN550 - DIAGRAMMI TECNICI N. N.
Antec, Inc. 47900 Fremont Blvd. Fremont, CA 94538 Tel: 510-770-1200 Fax: 510-770-1288 Antec Europe B.V. Sydneystraat 33 3047 BP Rotterdam The Netherlands Tel: +31 (0) 10 462-2060 Fax: +31 (0) 10 437-1752 Technical Support US & Canada 1-800-22ANTEC CustomerSupport@antec.com Europe +31 (0) 10 462-2060 europe.techsupport@antec.com www.antec.com © Copyright 2005 Antec, Inc. All rights reserved. All trademarks are the property of their respective owners.
